Tuning Wiki

Browse these projects from Modded Cars: Volkswagen PD builds.

Scope and how to read the figures

These are documented examples of Volkswagen Group 1.9-litre eight-valve PD (unit-injector) builds, not guaranteed stage recipes. The figures and component lists are reported by the builders; dyno method, correction and wheel-versus-crank basis are not established consistently by the project pages. A car may have changed since it was photographed. Nitrous-assisted results are marked separately from the reported diesel-only results.

Identify the actual engine, injector body and ECU before ordering parts. For injector numbers, nozzle references, delivery and timing checks, see PD injection and nozzle identification.

Around 250 bhp: Ibiza ATD

Rear view of the red Darkside Ibiza ATD project

Image: Darkside Developments, Ibiza ATD project gallery. Reproduced with user-stated permission.

Reported: 249.8 bhp and 430 lb ft (584 Nm); 1.9 PD ATD, HDS 02M six-speed. Darkside lists its Hybrid Killer turbo, PD injectors with Firad 50% nozzles, SeatSport intercooler and pipework, PD150 inlet and head bolts, and custom calibration. The project also lists a single-mass flywheel, sintered clutch and Quaife limited-slip differential. Rods and bottom-end specification are not stated. Builder's specification.

Approaching 300 bhp: Ibiza ASZ

Grey Ibiza ASZ on the Darkside dynamometer

Image: Darkside Developments, Ibiza ASZ project gallery. Reproduced with user-stated permission.

Reported: 287 bhp and 430 lb ft (584 Nm); 1.9 PD ASZ and FSM 02M six-speed. The listed combination includes a GTB2260VK turbo kit, PD injectors with Firad 100% nozzles, race cam, PD150 head bolts, custom intake, front-mounted intercooler and custom remap. Transmission work includes a single-mass flywheel and organic clutch, Quaife differential and selector reinforcement. The page does not establish a complete bottom-end specification. Builder's specification.

300–450 bhp: Bora ASZ, diesel-only and nitrous

Bora ASZ project engine on a stand during assembly

Image: Darkside Developments, Bora ASZ project gallery. Reproduced with user-stated permission. The build-stage image does not establish the configuration at every recorded run.

Reported: 326 bhp and 420 lb ft (570 Nm) diesel-only; 449 bhp and 580 lb ft (787 Nm) with nitrous. Darkside identifies an ASZ-based 1.9 PD with GTD2872VRK billet hybrid turbo, Firad +160% PD nozzles, ported head, oversized valves, race cam, head and main studs, Rosten H-beam rods and machined BHW pistons. It also lists an intercooler, FASS lift-pump kit, oil cooling, water injection, a dry nitrous kit and custom remap. This is a highly modified example, not evidence that the same result is available without nitrous. Builder's current project page.

340–450 bhp: Ibiza BLT drag build

Engine bay of the Ibiza BLT PD drag project

Image: Darkside Developments, Ibiza BLT project gallery. Reproduced with user-stated permission. The photo may show a different build stage.

Reported: 343.7 bhp and 405 lb ft (550 Nm) without nitrous; 451.1 bhp and 560 lb ft (760 Nm) with nitrous. The listed BLT-based build uses a Holset HX turbo, Firad +160% PD nozzles, ported head, oversize valves, uprated springs, race cam, head studs and machined coated pistons, plus intercooling, water injection and custom mapping. The 02M transmission has a solid input shaft, sintered clutch, plated differential and reinforcement. Darkside reports a 10.64-second quarter mile; it is a drag-oriented build and does not document con-rod specification on this project page. Builder's project and previous specifications.

260 bhp: Golf Mk5 BKC owner build

Owner-reported: 260 bhp and 425 lb ft from a 1.9 PD105 BKC. The owner lists a GTB2260VK with billet compressor, tubular manifold, Firad +80% race PD injectors, S3 intercooler, PD150 head bolts and custom ECU calibration. The build also includes an 02Q six-speed conversion, reinforced selector forks, Quaife differential and uprated organic clutch. The forum post does not establish dyno conditions or a complete bottom-end specification. Owner's build thread.

369–427 bhp: Golf Mk4 ARL 4Motion

Engine bay and front intercoolers of the Golf Mk4 ARL 4Motion project

Image: Darkside Developments, Golf 4Motion project gallery. Reproduced with user-stated permission; photo may show a different build stage.

Builder-reported: 368.6 bhp and 475 lb ft without nitrous; 426.7 bhp and 560 lb ft with nitrous. This ARL PD has a compound GTB1749V high-pressure and Holset HX35W low-pressure arrangement, dual intercoolers, Firad +120% injectors, ported head, oversize valves, race cam, Rosten rods and 2.0 BHW pistons. The 4Motion driveline has front and rear limited-slip differentials, a sintered clutch and modified Haldex. The builder reports a 12.3-second quarter mile. Builder's specification.

350–425 bhp: Fabia vRS ASZ

Red Fabia vRS ASZ project at a motorsport venue

Image: Darkside Developments, Fabia project gallery. Reproduced with user-stated permission; photo may show a different build stage.

Builder-reported: 350 bhp and 460 lb ft diesel-only; approximately 425 bhp and 600 lb ft with nitrous. The ASZ-based build lists a GTB2566VK turbo, Firad +160% PD injectors, Rosten H-beam rods, ported head, oversized valves, race cam, piston valve cut-outs and head studs. The builder also lists intercooling, water/methanol injection, a 02M six-speed with limited-slip differential and gearbox reinforcement, and an 11.6-second quarter mile. The assisted figure is approximate. Builder's specification.

300+ hp: Golf Mk4 ARL owner listing

Silver Golf Mk4 ARL PD150 described in the 300 hp owner listing

Photo: leewhitehouse's 2018 Swapz vehicle listing; photographer not specified. Reproduced with user-stated permission. The listing is a historical account.

Owner-reported: 300+ hp and 384 lb ft, with dyno printouts said to be available; the printouts and measurement basis have not been independently checked. The owner identifies a 1.9 ARL PD150, Firad +80% nozzles, front-mounted intercooler with alloy boost piping, 4 bar MAP sensor, custom 2.5-inch exhaust and rebuilt DRW six-speed. The owner describes a water-cooled ball-bearing turbo with vacuum conversion: the prose calls it GTB2660VKLR while the detailed list calls it GTB2260VKLR, so the exact model is unconfirmed. Bottom-end modifications are not specified. Owner's description and photographs.

Estimated 450 hp: Corrado PD130 4Motion swap

VAGbuilders Corrado with PD130 engine swap

Photo: Engine Swap Depot's VAGbuilders Corrado feature; the feature credits VAGbuilders and Officially Gassed. Photographer not specified. Reproduced with user-stated permission.

Estimated, not a verified dyno result: approximately 450 hp as reported by Engine Swap Depot from VAGbuilders' account; torque, measurement basis and whether the figure involved assistance are not established in the feature. Its 1990 Corrado has a 1.9 PD130 swap, forged rods, ported head, a 272 cam specification, custom exhaust manifold, water-to-air intercooler and Skillaturbo 2971 turbo; the six-speed and first-generation Haldex 4Motion system were upgraded. The source does not give the precise engine code or injector/nozzle specification. Engine Swap Depot feature; linked project video.

S-Tune Golf Mk4 ARL: 343 bhp

S-Tune Golf Mk4 ARL on a dynamometer

Photo: S-Tune project gallery; photographer not specified. Reproduced with user-stated permission.

Builder-reported: 343 bhp and 651 Nm. The 2025 project identifies a 1.9 PD150 ARL, GTB2872bb turbo, Firad 120% injectors, 272 camshaft, custom intercooler and remap, PD150 head bolts, and Sachs SRE paddle clutch. A Snow Performance methanol-injection system is listed; the project does not say whether it was operating for the quoted figure. S-Tune describes a full engine and gearbox build and nitrous as future plans, not proven features of this recorded configuration. Dyno method and measurement basis are not specified. S-Tune build specification.

AR Performance Golf Mk4: 449 bhp diesel / 590 bhp with nitrous

AR Performance Golf Mk4 PD engine bay with green rocker cover

Photo: AR Performance customer builds gallery; photographer not specified. Reproduced with user-stated permission; photographs can represent a different build stage.

Builder-reported: 449 bhp on diesel, 828 Nm, and 590 bhp with nitrous. AR Performance describes its Mk4 Anniversary demo as a built 1.9 TDI with machined ARL pistons, Pro Race Engineering rods, ported head, 272° dBilas cam, Firad 120% injectors, ceramic-coated custom GTD30 turbo, S3 intercooler, Sachs SRE paddle clutch, custom calibration and a two-stage ZEX nitrous kit. The builder labels the 449 bhp result diesel-only with no additives; it does not clearly specify which run produced 828 Nm, the original engine code, or the measurement basis. These reported numbers have not been independently verified. AR Performance project specification.

What the examples do and do not prove

  • Air and fuel work together. The listed builds combine turbo, charge cooling, injector/nozzle selection and calibration. A nozzle percentage is a supplier designation, not a guaranteed gain or a universal duration setting.
  • Inspect the baseline. Check compression, oil supply and condition, cam lobes, injector bores, fuel delivery and cooling before relying on upgraded hardware; investigate existing faults first.
  • Engine and drivetrain are a system. The examples show different head, bottom-end, clutch, differential and gearbox choices. The presence of a part on one car does not prove it is mandatory or durable at the same output on another.
  • Use measured evidence. Retain injector bench sheets, dyno graphs and test conditions, and log relevant pressure, temperature and fueling channels for the actual ECU. Compare diesel-only and assisted runs separately; torque and its rpm range matter alongside peak power.
  • Fitment and use: application differences, emissions equipment and local road rules matter. Follow the relevant repair procedures and validate the whole vehicle for its intended use.

Photographs and build accounts are credited individually above. Image reuse permission was stated by the user; no separate licence terms were supplied. Research reviewed 18 November 2026.