Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engines
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

The Bosch CP3 R110 is a family of three-plunger radial common-rail diesel high-pressure pumps. It is relevant when identifying original Volvo and Hyundai applications or considering a higher-capacity fuel-system build. R110 is a type designation, not a complete part number, an automatic M57 fitment or a guaranteed horsepower rating. Start with the exact Bosch number and type suffix.

Operation and identification

CP3 pumps use three radial pumping elements and suction-side metering to regulate fuel delivered to the high-pressure circuit. Actual output changes with pump shaft speed, rail pressure, inlet conditions, fuel temperature, metering command and condition. Compare test-bench flow reports at matching conditions rather than treating R110, R90 and R70 names as measured flow figures. Bosch common-rail catalogue.

Bosch number and typeDocumented application or descriptionIdentification limit 0 445 010 110; CR/CP3S3/R110/30-8911SBosch catalogue lists a Volvo XC90 I D5 AWD 2.4, 120 kW, January 2003–July 2006; it also lists a specified XC60 2.4D AWD.Catalogue examples, not every Volvo D5. Verify VIN and installed number. Bosch catalogue. 0 445 010 111; CR/CP3S3/R110/30-8911SBosch CP3 training lists a Volvo application; a diesel specialist lists it with the 110 as a related pump.Confirm exact replacement and current supersession for the vehicle. Bosch training list; diesel specialist listing. 0 445 010 043; CR/CP3S3/R110/30-789SBosch training lists a Volvo R110 variant with a different suffix.Different suffixes and metering components require part-specific checks. Bosch training list. 0 445 010 342; CR/CP3S3/R110/30-89SBosch catalogue lists Hyundai Santa Fe 2.2 CRDi 4x4, 110 kW, March 2006–November 2009.Check fitment by VIN and actual number rather than by vehicle name alone. Bosch catalogue.

Audi L110 is a separate designation

Bosch 0 445 010 119 is listed as CR/CP3S3/L110/30-789S, not R110. A diesel specialist lists it for specified Audi A8/Q7 4.2 TDI BMC, BVN and BTR applications. Do not ignore the L/R character or assume the same drive direction, flange, control or interchangeability. Verify the exact Audi engine, VIN, installed pump and supersession. CP3 test-plan list; Audi 4.2 TDI specialist listing. Audi 2.7/3.0 V6 examples include different CP3 R90 numbers.

Considering R110 for an M57 or dual-pump build

A pump from a larger-capacity family may be considered if the existing fuel system cannot maintain rail pressure at the required delivery. The sources here establish donor pump identities, not a proven direct-fit R110 conversion for the BMW M57 twin-turbo. A kit accepting R70/R90 pumps does not automatically accept an R110. Do not infer a gain, pressure rating, safe engine limit or supported power from the label alone.

Compare flange and pump body clearance, shaft, coupling or pulley, drive rotation and speed, and mounting and belt loads.Check low-pressure inlet and return, metering-valve type and control, electrical connector, high-pressure outlet and suitable lines, pressure regulator and sensor compatibility.On a second-pump setup, verify the bracket, pulley ratio, belt, dedicated control and fail-safe, sufficient low-side feed and rail-pressure stability across operating conditions.Obtain a bench report for the exact pump at relevant speed and pressure. Log requested and actual rail pressure and low-side supply, then assess injector delivery, turbo airflow, charge cooling, temperatures and transmission capacity as a complete system.

More pump delivery does not by itself increase injector flow or permit a higher rail pressure. Rail, sensor, injectors, lines and controls must all remain within their specified ratings. See the M57 hybrid and dual CP3 guide and CP3 family guide.

Diagnosis and safe service

Before condemning a pump for low rail pressure, check the filter and low-pressure supply under load, air entry, electrical and metering control, rail-pressure sensor and regulator, and injector return leakage. Compare requested and actual pressure under the specified test conditions. An individual fault code or pressure drop does not identify the failed part on its own.

Common-rail fuel can remain at very high pressure after shutdown. Follow the manufacturer’s depressurisation and clean-work procedures; never loosen a live high-pressure connection or use a hand to locate a leak. Use specified replacement lines and fittings. If a pump has failed internally, inspect and clean the complete fuel system in accordance with the manufacturer’s repair procedure. See fuelling faults.

An adapted CP4.2 is another M57 upgrade path; see the M57 twin-turbo guide for supplier examples and fitment checks.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Bosch CP3 R110 high-pressure fuel pumps

The Bosch CP3 R110 is a family of three-plunger radial common-rail diesel high-pressure pumps. It is relevant when identifying original Volvo and Hyundai applications or considering a higher-capacity fuel-system build. R110 is a type designation, not a complete part number, an automatic M57 fitment or a guaranteed horsepower rating. Start with the exact Bosch number and type suffix.

Operation and identification

CP3 pumps use three radial pumping elements and suction-side metering to regulate fuel delivered to the high-pressure circuit. Actual output changes with pump shaft speed, rail pressure, inlet conditions, fuel temperature, metering command and condition. Compare test-bench flow reports at matching conditions rather than treating R110, R90 and R70 names as measured flow figures. Bosch common-rail catalogue.

Bosch number and typeDocumented application or descriptionIdentification limit
0 445 010 110; CR/CP3S3/R110/30-8911SBosch catalogue lists a Volvo XC90 I D5 AWD 2.4, 120 kW, January 2003–July 2006; it also lists a specified XC60 2.4D AWD.Catalogue examples, not every Volvo D5. Verify VIN and installed number. Bosch catalogue.
0 445 010 111; CR/CP3S3/R110/30-8911SBosch CP3 training lists a Volvo application; a diesel specialist lists it with the 110 as a related pump.Confirm exact replacement and current supersession for the vehicle. Bosch training list; diesel specialist listing.
0 445 010 043; CR/CP3S3/R110/30-789SBosch training lists a Volvo R110 variant with a different suffix.Different suffixes and metering components require part-specific checks. Bosch training list.
0 445 010 342; CR/CP3S3/R110/30-89SBosch catalogue lists Hyundai Santa Fe 2.2 CRDi 4x4, 110 kW, March 2006–November 2009.Check fitment by VIN and actual number rather than by vehicle name alone. Bosch catalogue.

Audi L110 is a separate designation

Bosch 0 445 010 119 is listed as CR/CP3S3/L110/30-789S, not R110. A diesel specialist lists it for specified Audi A8/Q7 4.2 TDI BMC, BVN and BTR applications. Do not ignore the L/R character or assume the same drive direction, flange, control or interchangeability. Verify the exact Audi engine, VIN, installed pump and supersession. CP3 test-plan list; Audi 4.2 TDI specialist listing. Audi 2.7/3.0 V6 examples include different CP3 R90 numbers.

Considering R110 for an M57 or dual-pump build

A pump from a larger-capacity family may be considered if the existing fuel system cannot maintain rail pressure at the required delivery. The sources here establish donor pump identities, not a proven direct-fit R110 conversion for the BMW M57 twin-turbo. A kit accepting R70/R90 pumps does not automatically accept an R110. Do not infer a gain, pressure rating, safe engine limit or supported power from the label alone.

  • Compare flange and pump body clearance, shaft, coupling or pulley, drive rotation and speed, and mounting and belt loads.
  • Check low-pressure inlet and return, metering-valve type and control, electrical connector, high-pressure outlet and suitable lines, pressure regulator and sensor compatibility.
  • On a second-pump setup, verify the bracket, pulley ratio, belt, dedicated control and fail-safe, sufficient low-side feed and rail-pressure stability across operating conditions.
  • Obtain a bench report for the exact pump at relevant speed and pressure. Log requested and actual rail pressure and low-side supply, then assess injector delivery, turbo airflow, charge cooling, temperatures and transmission capacity as a complete system.

More pump delivery does not by itself increase injector flow or permit a higher rail pressure. Rail, sensor, injectors, lines and controls must all remain within their specified ratings. See the M57 hybrid and dual CP3 guide and CP3 family guide.

Diagnosis and safe service

Before condemning a pump for low rail pressure, check the filter and low-pressure supply under load, air entry, electrical and metering control, rail-pressure sensor and regulator, and injector return leakage. Compare requested and actual pressure under the specified test conditions. An individual fault code or pressure drop does not identify the failed part on its own.

Common-rail fuel can remain at very high pressure after shutdown. Follow the manufacturer’s depressurisation and clean-work procedures; never loosen a live high-pressure connection or use a hand to locate a leak. Use specified replacement lines and fittings. If a pump has failed internally, inspect and clean the complete fuel system in accordance with the manufacturer’s repair procedure. See fuelling faults.

Revision 2: Bosch CP3 R110 high-pressure fuel pumps

The Bosch CP3 R110 is a family of three-plunger radial common-rail diesel high-pressure pumps. It is relevant when identifying original Volvo and Hyundai applications or considering a higher-capacity fuel-system build. R110 is a type designation, not a complete part number, an automatic M57 fitment or a guaranteed horsepower rating. Start with the exact Bosch number and type suffix.

Operation and identification

CP3 pumps use three radial pumping elements and suction-side metering to regulate fuel delivered to the high-pressure circuit. Actual output changes with pump shaft speed, rail pressure, inlet conditions, fuel temperature, metering command and condition. Compare test-bench flow reports at matching conditions rather than treating R110, R90 and R70 names as measured flow figures. Bosch common-rail catalogue.

Bosch number and typeDocumented application or descriptionIdentification limit
0 445 010 110; CR/CP3S3/R110/30-8911SBosch catalogue lists a Volvo XC90 I D5 AWD 2.4, 120 kW, January 2003–July 2006; it also lists a specified XC60 2.4D AWD.Catalogue examples, not every Volvo D5. Verify VIN and installed number. Bosch catalogue.
0 445 010 111; CR/CP3S3/R110/30-8911SBosch CP3 training lists a Volvo application; a diesel specialist lists it with the 110 as a related pump.Confirm exact replacement and current supersession for the vehicle. Bosch training list; diesel specialist listing.
0 445 010 043; CR/CP3S3/R110/30-789SBosch training lists a Volvo R110 variant with a different suffix.Different suffixes and metering components require part-specific checks. Bosch training list.
0 445 010 342; CR/CP3S3/R110/30-89SBosch catalogue lists Hyundai Santa Fe 2.2 CRDi 4x4, 110 kW, March 2006–November 2009.Check fitment by VIN and actual number rather than by vehicle name alone. Bosch catalogue.

Audi L110 is a separate designation

Bosch 0 445 010 119 is listed as CR/CP3S3/L110/30-789S, not R110. A diesel specialist lists it for specified Audi A8/Q7 4.2 TDI BMC, BVN and BTR applications. Do not ignore the L/R character or assume the same drive direction, flange, control or interchangeability. Verify the exact Audi engine, VIN, installed pump and supersession. CP3 test-plan list; Audi 4.2 TDI specialist listing. Audi 2.7/3.0 V6 examples include different CP3 R90 numbers.

Considering R110 for an M57 or dual-pump build

A pump from a larger-capacity family may be considered if the existing fuel system cannot maintain rail pressure at the required delivery. The sources here establish donor pump identities, not a proven direct-fit R110 conversion for the BMW M57 twin-turbo. A kit accepting R70/R90 pumps does not automatically accept an R110. Do not infer a gain, pressure rating, safe engine limit or supported power from the label alone.

  • Compare flange and pump body clearance, shaft, coupling or pulley, drive rotation and speed, and mounting and belt loads.
  • Check low-pressure inlet and return, metering-valve type and control, electrical connector, high-pressure outlet and suitable lines, pressure regulator and sensor compatibility.
  • On a second-pump setup, verify the bracket, pulley ratio, belt, dedicated control and fail-safe, sufficient low-side feed and rail-pressure stability across operating conditions.
  • Obtain a bench report for the exact pump at relevant speed and pressure. Log requested and actual rail pressure and low-side supply, then assess injector delivery, turbo airflow, charge cooling, temperatures and transmission capacity as a complete system.

More pump delivery does not by itself increase injector flow or permit a higher rail pressure. Rail, sensor, injectors, lines and controls must all remain within their specified ratings. See the M57 hybrid and dual CP3 guide and CP3 family guide.

Diagnosis and safe service

Before condemning a pump for low rail pressure, check the filter and low-pressure supply under load, air entry, electrical and metering control, rail-pressure sensor and regulator, and injector return leakage. Compare requested and actual pressure under the specified test conditions. An individual fault code or pressure drop does not identify the failed part on its own.

Common-rail fuel can remain at very high pressure after shutdown. Follow the manufacturer’s depressurisation and clean-work procedures; never loosen a live high-pressure connection or use a hand to locate a leak. Use specified replacement lines and fittings. If a pump has failed internally, inspect and clean the complete fuel system in accordance with the manufacturer’s repair procedure. See fuelling faults.

An adapted CP4.2 is another M57 upgrade path; see the M57 twin-turbo guide for supplier examples and fitment checks.