Secondary air injection (SAI), also called an air-injection or air-injection reaction (AIR) system, supplies fresh air to the exhaust on certain petrol engines. In workshop language the pump is often called a smog pump or anti-smog pump. The added oxygen helps oxidise carbon monoxide (CO) and unburned hydrocarbons (HC) in hot exhaust and, on suitable catalyst-equipped systems, helps the catalyst warm up after a cold start. The parts, controls and operating schedule vary with the engine; not every petrol engine has this system.
This page explains the equipment and diagnosis. See also petrol and diesel emissions, lambda sensors and emissions testing equipment.
What secondary air does
A cold petrol engine and cold catalytic converter can produce relatively high HC and CO emissions. Supplying oxygen to sufficiently hot exhaust permits further oxidation of CO and HC to carbon dioxide and water; the heat released can help a catalyst reach its effective operating temperature sooner. Secondary air is added to the exhaust, rather than being the air metered into the engine for combustion. The actual effect depends on temperature, mixing, exhaust composition and the vehicle's calibration. HELLA: secondary air system; MIT: effects of secondary air during cold start.
A modern electric-pump installation commonly operates for a short period following a qualifying cold start. Pump duration, temperature thresholds and valve timing are vehicle-specific; a warm engine or a recently run pump may not meet the conditions for operation. Some monitored systems also activate the pump with a warm engine to test system response. A silent pump outside its commanded operating window is not proof of failure. Motorservice gives a warm-engine diagnostic-monitor example; do not assume the same monitor sequence applies to all vehicles. Motorservice: design and troubleshooting.
Typical layout and components
A common electrically driven arrangement can be represented as:
Filtered fresh air → electric air pump → air hose → secondary-air / combination valve → exhaust port or manifold → catalyst.
The ECU controls the pump through a relay or other power stage and controls the air valve according to the vehicle's design. A vacuum-operated version may use a solenoid switching valve and a vacuum line to operate the combination valve. Another design may use an electrically actuated valve. The diagram is a typical path, not a wiring or hose diagram for a particular model. HELLA: active-system construction.
| Part | Purpose | Typical fault to investigate |
|---|---|---|
| Air pump and inlet filter | Supply clean fresh air at sufficient pressure and flow when commanded. | Seized or noisy pump; water damage; blocked inlet; electrical supply or drive fault. |
| Relay, fuse, wiring or electronic power stage | Allow the control unit to energise the pump as required. | Open fuse, damaged wiring, corroded connection or relay stuck on/off. A continuously energised pump may overheat. |
| Secondary-air or combination valve | Admit air when commanded and prevent hot exhaust flowing back toward the pump. | Sticking, leakage, failed actuator or carbon fouling; check the actual valve arrangement. |
| Vacuum solenoid, reservoir and hoses, where fitted | Apply or release vacuum to operate a pneumatic valve. | Leaking hose, failed solenoid, poor vacuum supply or leaking valve diaphragm. |
| Air pipes, injection passages and exhaust connection | Carry and distribute air to the exhaust. | Split hose, exhaust leak, corroded pipe or blocked port. |
Loss of non-return function is important: exhaust gas and its condensate can travel back into the air pump, corroding or damaging it. Finding water or deposits on the pump side calls for investigation of the valve and air inlet as well as the pump. Replacing only the pump can leave the original cause in place. Motorservice: pump and valve faults.
Older belt-driven and passive systems
Older air-injection reaction systems can use an engine belt-driven pump, air distribution pipes to exhaust ports and a one-way check valve. A diverter or anti-backfire valve on some older systems redirects pump output during deceleration; some use a different gulp-valve arrangement. Pump operation and routing need not follow the short cold-start schedule of a modern electrically controlled pump. Inspect the correct vehicle service information, belt and hose routing before drawing conclusions. The US EPA training guide on historic AIR systems illustrates one family of belt-driven pumps and valves.
Some other systems use exhaust pressure pulses and an appropriate valve to draw in secondary air without an electrically driven pump. An absent pump is therefore not by itself evidence of missing equipment. HELLA describes active and passive arrangements in its secondary-air overview.
How it differs from other emissions systems
- EGR recirculates a controlled portion of exhaust into the intake to influence combustion and reduce NOx formation; secondary air supplies fresh air to the exhaust.
- EVAP stores and purges fuel vapour; it is not the exhaust-air pump circuit.
- Three-way catalyst and lambda sensors treat and monitor exhaust chemistry. Secondary air supports cold-start emissions control on applicable vehicles but does not replace the catalyst or its normal mixture-control system.
- DPF or OPF/GPF captures particulate matter. It has a different job from an air-injection system.
“Anti-smog” is used loosely for several emissions-control systems, so identify the actual components rather than assuming the term means the same hardware on every vehicle.
Symptoms, codes and likely causes
Symptoms can include a warning lamp, a stored secondary-air fault, unusual pump noise at a qualifying start or a pump that runs when it should not. Increased cold-start HC and CO can occur even where there is little obvious drivability complaint. A warm idle emissions test is only a snapshot and cannot establish correct cold-start operation. HELLA: symptoms and causes.
Generic code P0410 denotes a secondary-air system malfunction and P0411 indicates incorrect flow; Motorservice describes an insufficient-flow example. Codes and descriptions vary with the diagnostic system. A flow fault does not identify which part failed: a pump may run but deliver insufficient flow because of a restriction, leaking hose, stuck valve or blocked exhaust passage. An electrical fault can involve a fuse, relay, power, ground, wiring, actuator or control. Check model-specific fault criteria and freeze-frame conditions. Motorservice: OBD and troubleshooting examples.
Some systems monitor an expected oxygen-sensor response when air is introduced. That is a system-level test: a bad sensor, leak or flow fault can affect the result, and an actuator test showing a running pump does not by itself prove air reaches the exhaust. A valve leaking when it should be closed can also affect exhaust oxygen readings in some layouts. Confirm the design and test conditions before interpreting a lambda trace. Motorservice: OBD monitoring and valve checks.
Workshop diagnosis
- Identify the system. Confirm the engine, equipment, air path, electrical and vacuum diagrams, fault codes and recorded conditions. Determine whether the vehicle uses an electric pump, a mechanical pump or passive air supply.
- Inspect with the engine off and components cool. Look for damaged or disconnected air and vacuum hoses, a blocked inlet, heat damage, damaged wiring, fuses, relay condition and leaks around the exhaust connection. On belt-driven systems check the belt and drive as specified.
- Confirm the commanded conditions. If suitable, observe a genuinely cold start or use the manufacturer's supported scan-tool actuator test. Compare command with pump operation and valve operation. Pump running time and monitor conditions depend on the vehicle; avoid repeated or prolonged pump operation outside its specified duty cycle.
- Separate electrical supply from the pump. When commanded, check voltage supply, ground and relay or control operation using the correct wiring diagram and test method. A good fuse alone does not prove correct voltage under load. Do not apply external power or bridge terminals without the manufacturer's procedure.
- Check the valve and delivery path. On vacuum-operated designs use the specified hand-vacuum test to check the actuator and its ability to hold vacuum. Check the solenoid and vacuum supply separately. Inspect for moisture or exhaust deposits on the pump side, restricted pipes and blocked ports. On electric valves use the applicable electrical and actuator tests. Do not force compressed air through components.
- Repair the cause and verify. Restore damaged components and the reason for their failure, then check commanded operation and run the specified monitor or drive cycle. Clear fault codes when appropriate and recheck for recurrence and leaks.
These checks follow the principles in HELLA's diagnostic guide and Motorservice's service instruction. They are not a substitute for the exact vehicle procedure. Keep clear of moving belts and hot exhaust parts and use suitable exhaust extraction; see HSE vehicle exhaust guidance.
MOT and equipment condition
The DVSA MOT inspection manual, section 8 defines the applicable checks for manufacturer-fitted emission-control equipment, exhaust leaks and malfunction indicators. Consult the current manual for the vehicle being tested. A normal reading on a warm tailpipe test does not by itself demonstrate that a cold-start secondary-air system works.
Sources and further reading
- HELLA Tech World: secondary air injection — active and passive systems, valve operation, symptoms and checks.
- Motorservice / Pierburg: secondary-air system design and troubleshooting — components, monitor examples, valve and vacuum tests.
- Motorservice: troubleshooting the secondary-air system — relay, moisture and return-valve faults.
- US EPA: Motor Vehicle Emissions Control, Book Three, Air Injection Reaction Systems — historic belt-driven pump, air manifold, diverter and check valves.
- D. Lee, MIT, Effects of secondary air injection during cold start of SI engines — experimental cold-start oxidation and catalyst warm-up.
- DVSA MOT inspection manual: emissions and HSE: vehicle exhaust emissions.