Tuning Wiki

After the five-volt boot-block parts, external program flash moved to a 3 V page-mode bus and, later, to a serial NOR device on SPI. The five-volt catalogue is Am29F and M29F. The burst parts that share the PowerPC years with the early 3 V devices are on Burst flash on PowerPC controllers. This page is the catalogue that followed, from the datasheets and cross-references. A part number printed on a board is still the identification. The tables are the families those datasheets offer for automotive temperature, not a fitment list for a named ECU.

Spansion and Cypress S29GL-N

The S29GL-N family is 3.0 V single-supply flash on 110 nm MirrorBit technology. Cypress's datasheet for the smaller pair, document 001-98525, gives the organisations. The S29GL032N is 32 Mbit, 2,097,152 words or 4,194,304 bytes. The S29GL064N is 64 Mbit, 4,194,304 words or 8,388,608 bytes. Depending on the model the bus is 16-bit only, or 16-bit with a BYTE# pin that selects an 8-bit bus. Access times as fast as 90 ns are listed, and each speed has its own supply window in the selector guide. Packages include 48-pin TSOP, 56-pin TSOP, 48-ball BGA and 64-ball BGA, depending on the model. The command set is the JEDEC single-supply set, and the datasheet says the devices can be programmed in a standard EPROM programmer.

The ordering block for the S29GL032N uses the letter A for automotive, AEC-Q100 Grade 3, −40 °C to +85 °C, and I for industrial over the same temperatures. Model numbers in that block select uniform sectors or a top or bottom boot, and which end a write-protect pin locks. Grade 3 on this datasheet is −40 °C to +85 °C. Micron's M29F datasheet uses grade 3 for −40 °C to +125 °C. The digit is not a shared temperature code.

The 3 V boot-block parts in the SST cross-reference

SST's base-memory cross-reference is the list that puts the smaller 3 V devices next to each other. These are the x16 rows, at 2.7 V to 3.6 V or 3.0 V to 3.6 V depending on the column the table is using.

DensitySSTAMDSTIntel names in the same row
8 MbitSST39VF800A, SST39LF800AAM29LV800M29W80028F800B3, 28F800C3, and further 28F800 suffixes in that cell
16 MbitSST39VF160AM29LV160M29W16028F160S3, 28F160B3, 28F160C3

The same table's byte-wide 3 V rows run from SST39VF512, SST39VF010, SST39VF020 and SST39VF040 up through SST39VF080 and SST39VF016, opposite AM29LV and M29W numbers of the same density. Elnec's device list adds a pair of suffixes the cross-reference collapses: SST39VF1601 and SST39VF1602, and the same 1 and 2 suffixes on the 320 and 640 devices, in TSOP48 and BGA. Which of those two suffixes is the top boot block is set by the SST datasheet for that device, and it is not assigned on this page.

Serial NOR

Winbond's 2025 code-storage selection guide is the manufacturer statement for the serial generation. The automotive NOR families it names are W25H-JV, W25Q-JV, W25Q-RV, W25Q-JW, W25Q-EW and W25H-NW, with octal NOR W35T-NW and serial NAND families beside them. The guide states 125 °C operation and AEC-Q100 for those automotive lines. The applications it prints for them are domain and zonal controllers, instrument clusters, ADAS and driver monitoring, gateway and domain controllers, eCockpit, infotainment and cameras. That is a different job from the execute-in-place parallel NOR on an ME7 or an EDC16. A W25Q device on a cluster or a gateway is the serial generation. The guide does not assign a density to a named engine controller.

The parallel page-mode parts above remain the ones a 3 V address and data bus can boot from directly. Serial NOR is fetched by the processor or by a companion. Which of those two arrangements a later controller uses is a property of that controller, on the microcontroller pages.

Sources