Tuning Wiki

The five-volt boot-block NOR devices are the external program memories of the generation after the socketed EPROM. AMD's Am29F400B is the part the datasheets describe in full here, because it is the 4 Mbit device, 512 Kbytes, that tool listings and the NefMoto ME7 notes both name. The 2, 8 and 16 Mbit siblings use the same command set and the same boot-block idea. Micron's M29F family is the later automotive continuation of that set. How this generation sits between EPROM and burst flash is on Automotive external flash.

Am29F400B

AMD's Am29F400B datasheet describes a 4 Mbit device organised as 524,288 bytes or 262,144 words. Read, program and erase use a single 5.0 V supply. A 12 V programming pin is not required. The packages are a 44-pin small-outline package and a 48-pin TSOP. One ordering edition also distinguishes a standard TSOP pinout from a reverse TSOP pinout, so a replacement has to match the pinout letter and not only the package size. Access times in the editions checked start at 45 ns or 55 ns depending on the process revision. The later distinctive-characteristics list gives a minimum of 1,000,000 program and erase cycles per sector, and one edition states 20-year data retention at 125 °C.

The sector map in byte mode is one 16 Kbyte sector, two 8 Kbyte sectors, one 32 Kbyte sector and seven 64 Kbyte sectors. Word mode is the same split in 16-bit words. The ordering letter T puts the small sectors at the top of the map. B puts them at the bottom. On the top-boot device the datasheet's address table runs the seven 64 Kbyte sectors from 00000h, then 32 Kbytes at 70000h, two 8 Kbyte sectors, and the 16 Kbyte boot sector at 7C000h–7FFFFh. Temperature letters in that datasheet include industrial, −40 °C to +85 °C, and extended, −55 °C to +125 °C.

The device is command-set compatible with the JEDEC single-supply flash standard. The datasheet's embedded algorithms time the program and erase pulses internally. Sector protection can be set in a programmer, with a temporary unprotect for later changes. Those are the features a programmer is using when it offers an Am29F400BB or Am29F400BT algorithm. The bottom-boot and top-boot algorithms are not interchangeable.

The rest of the boot-block family

Micron's technical note TN-13-22, revision A of February 2013, lines the family up by sector count. The columns are 64 Kbyte, 32 Kbyte, 16 Kbyte and 8 Kbyte blocks.

AMD device in TN-13-2264 Kbyte blocks32 Kbyte16 Kbyte8 KbyteCapacity that count produces
Am29F200, listed as Am29F200B in the introduction and Am29F200D in the sector table31122 Mbit, 256 Kbytes
Am29F400B71124 Mbit, 512 Kbytes
Am29F800B151128 Mbit, 1 Mbyte
Am29F160D3111216 Mbit, 2 Mbytes

The same note says the Micron M29F200, M29F400 and M29F800 match the AMD signal names and the package pinout, and that the 16 Mbit pair does not match completely. It also says the M29F has no write-protect pin. The packages it names for the comparison are TSOP48 and SO44, with the M29F160F not offered in SO44. A board built for the AMD write-protect pin cannot be assumed to ignore that difference.

Micron M29F automotive parts

Micron's M29F datasheet, the 2 Mbit to 16 Mbit edition copyrighted 2013, keeps AMD's manufacturer code. The electronic signature is manufacturer code 01h. The device codes are split by boot location.

DeviceTop-boot codeBottom-boot code
M29F200F2251h2257h
M29F400F2223h22ABh
M29F800F22D6h2258h
M29F160F22D2h22D8h

A programmer that reports manufacturer 01h is reporting this signature. It is the code AMD used, and Micron kept it so the devices would identify as the parts they replace. The datasheet states 100,000 program and erase cycles per block, packages TSOP48 and SO44, with the 16 Mbit device not available in SO44, and AEC-Q100 automotive grades. Grade 3 in that sheet is −40 °C to +125 °C. Grade 6 is −40 °C to +85 °C. The suffix on these Micron parts is FT or FB, where AMD used BT or BB for the same top and bottom choice.

Where they are reported on controllers

Two independent trade sources name the 29F400 and 29F800 on Bosch ME7, and they do not claim the same device for every hardware number.

The NefMoto open-source project says that for ME7.x most flash chips are a 29F800BB, which it equates to 1 Mbyte, or a 29F400BB, which it equates to 512 Kbytes. Those are the bottom-boot suffixes. The project is a tuning tool's hardware notes, not a Bosch parts list, and it is the clearest public statement that both densities were fitted and that the bottom-boot variant is the one the authors were reading.

A parts seller, epic.net.ar, offers an AM29F400 in SOP44 and lists the controllers it claims that package fits: Bosch ME7.4.4, ME7.5.10, ME7.9.6 and ME7.9.20, EDC15C3, EDC15C2, EDC15C7 and EDC15C13, EDC MS6.3, Magneti Marelli IAW 4LV and IAW 48P2, a Mercedes PLD, Siemens SID901 and Siemens EMS3134. A seller's fitment list is a claim about the boards that seller stocks. Where it overlaps NefMoto, the overlap is ME7 and the 29F400 in the 44-pin package. It does not settle which hardware number inside ME7.5 carries 512 Kbytes and which carries 1 Mbyte. That is still a reading of the marking on the board.

EVC's OLS300 is sold with a PSOP44 adapter, which is the tool name for this 44-pin outline, alongside the DIP and PLCC adapters for the EPROMs. The OLS300 page has the adapter list. The processor on the ME7 side of this generation is the C167 family, which is outside the memory section and is not catalogued on this page.

Siemens Sirius32 and EMS3132 example

An Immo-Tools manual identifies an external AM29F200BB, 256 KiB, for its Sirius32, Sirius32N and EMS3132 application alongside a C167 processor. It describes a 16 KiB EEPROM-emulated area within the flash. A partial emulated-EEPROM read is therefore not the same thing as the full flash image. The manual also warns that Sirius32 and Sirius32N use different data layouts; identify the exact ECU and operation. VF2 application notes independently list AM29F200BB for Sirius32 and EMS3132.

Sources