The Motorola MPC555, MPC56x and related PowerPC controllers used a burst-mode NOR flash on the external bus. The processor can also contain its own flash. EVC's BDM100 page says the on-chip array on the MPC555 to MPC565 is 448 Kbytes to 1 Mbyte and cannot be read in an EPROM programmer, which is why that tool uses the background-debug port. The external device is still present on many of those boards, and it is a different part from the five-volt Am29F400. The processor side is on Motorola Freescale MPC5xx and MPC561 and MPC562.
The devices
ST application note AN1360 describes the M58BW016B and M58BW016D as a 3 V, 16 Mbit burst flash, connected to the MPC56x without glue logic in the method the note gives. It says the MPC56x is built for automotive use, runs up to 56 MHz across the automotive temperature range, and uses a 2.6 V core supply. The M58BW016 can meet that 56 MHz burst rate. The B suffix has tuning-block protection. The D suffix has that protection disabled. The note says the same approach is a reference for other ST burst flashes and for the MPC555, with the supply levels checked again for each case.
AMD's Am29BL802C datasheet, revision C of 22 November 2002, is an 8 Mbit device organised as 512 K × 16, in a 56-pin SSOP. The supply is 3.0 V to 3.6 V. Burst is a linear 32-word sequence with wrap, and the datasheet offers that burst in a bottom-boot configuration only. It powers up in asynchronous mode so that it remains compatible with the Am29F and Am29LV command sets, and it can then be placed in burst mode. Data, address and control inputs are 5 V tolerant. Initial access times are as fast as 65 ns, with a burst access of 17 ns in the industrial range.
AMD's Am29BDD160G datasheet, revision D of 2 February 2005, is a 16 Mbit device organised as 1 M × 16 or 512 K × 32. The supply is 2.5 V to 2.75 V. It is dual-boot, with simultaneous read and write on two banks, and a configurable burst. The same edition says that for new designs the S29CD016G supersedes it. Spansion's S29CD016J datasheet describes that successor family: the S29CD-J at 2.50 V to 2.75 V and the S29CL-J at 3.00 V to 3.60 V, burst mode, simultaneous read and write, configurable as 524,288 double words, command-set compatible with Am29F and Am29LV. The datasheet text checked here says operation up to 56 MHz. Infineon's page for the orderable S29CD016J0MFAM013 states 16 Mbit, a 2.6 V burst interface, 66 MHz, and −40 °C to 125 °C. Those are two documents, and the frequency is not the same number in both. The marking on the board decides which revision was fitted.
EVC's controller table
EVC's BDM100 support table is the published list that pairs these devices with controllers. It is a tool maker's support list. A dash means EVC did not name an external flash. A question mark is EVC's unknown. The FAQ beside that table adds a hardware warning: for some rows the data lines between processor and flash are exchanged. The rows EVC marks that way are the M58BW016 on EDC16, the 28F800F3 on ME9, the 29BL802 on EDC16, and the S29CD016 on EDC16+. The table is not a wiring diagram.
| Controller, as EVC names it | Processor | External flash EVC names |
|---|---|---|
| Bosch BMS-K, BMW K1200RS | MPC562 | M58BW016 |
| Bosch EDC16, VAG, BMW, Mercedes-Benz, PSA | MPC556 | AM29BL802 |
| Bosch EDC16+, PSA and BMW | MPC562 | M58BW016 |
| Bosch EDC16+, VAG | MPC564 | M58BW016 |
| Bosch EDC7, MAN and Iveco | MPC556 | None named |
| Bosch ME9.0C, Volvo and Ford Focus ST | MPC562 | M58BW016 |
| Bosch ME9, BMW four-cylinder and V8 | MPC555 | Two 28F800F3 |
| Bosch ME9.2, BMW | MPC564 | M58BW016 |
| Bosch ME9.3, BMW | MPC564 | S29CD016 |
| Bosch ME9.7, Mercedes-Benz | MPC564 | M58BW016 |
| Bosch MED9.1, Volkswagen Group 2.0 TFSI | MPC562 | M58BW016 |
| Bosch MED9.5.20, Volkswagen Group 1.6 and 2.0 FSI | MPC562 | M58BW016 |
| Bosch MED9.6.1, Mercedes-Benz, Ferrari F12 in EVC's example | MPC562 | M58BW16, EVC's spelling |
| Bosch MED9.7, Mercedes-Benz C350 | MPC564 | M58BW32FB |
| Delphi, Isuzu D-Max | MPC561 | M58BW016 |
| Siemens MS45, BMW six-cylinder | MPC555 | AM29BL802 |
| Siemens MSS60, BMW M3 | Two MPC563 | Two AM29BDD160 |
| Siemens MSS65, BMW M5 V10 | Two MPC563 | Two AM29BDD160 |
| Siemens MSV70 and MSS70 | MPC563 | AM29BDD160 |
| Siemens PPD1.x, Volkswagen Group 2.0 TDI | MPC561 | AM29BDD160 |
| Siemens SID201, SID202, SID203, SID204, SID206 | MPC563 | M58BW016 |
| Siemens SID803, Volvo diesel | MPC555 | AM29BL802 |
| Siemens SIM266 | MPC561 | AM29BDD160 |
| Siemens SIM2K, Hyundai | MPC561 | S29CD016 |
| Siemens SIM90E | MPC561 | AM29BDD160 |
| Siemens SIM90P | MPC561 | S29CD016 |
| Siemens Simos 6.x | MPC561 | AM29BDD160 |
EVC's FAQ lists the device families the probe supports, independent of the car: M58BW016 top and bottom, M58B008, 28F800F3 top and bottom, 29BL802, Am29BDD160, S29CD016, S29CL016, S29CD032, and M58BW32 top and bottom. The 28F800F3 is an Intel device. EVC's table is the source for it on the BMW ME9, as two chips on an MPC555. The Intel 28F reference now includes the automotive 28F800F3 datasheet and voltage information.
Rows EVC leaves without an external flash still have the processor's internal array. Caterpillar, Chrysler ETC5, John Deere, one Delphi Jaguar and Ford entry, Delphi DCM3.2, Marelli MJD and TRW EMS2 are in the same BDM100 table with a dash or a question mark in the flash column. Absence from this page is not a claim that those controllers have no program memory.