Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

Scope: This guide concerns the illustrated EA888 Gen 3 CHHB/CHHA engine and its Simos 18.1 management, not every engine with a Simos 18 ECU. Pump design, switches and software vary by engine code. Calibration examples below are from the community SC8S5031_C_OEM reference; match the target software, function, units, axes and operating conditions. Volkswagen SSP 522 and community ENLU oil-setpoint reference.

Two-stage oil pressure control

In SSP 522's example, the engine-driven external-gear oil pump uses a hydraulically moved slide and the ECU-controlled N428 valve to select low or high delivery stages. Load and engine speed participate in switching; warm-up, faults and other states can also affect the request. The physical pressure produced depends on the engine, oil condition, temperature, speed and mechanical system, not just the requested stage. Volkswagen describes N428's failed closed condition as high-stage operation for this example. Do not generalize that failure behavior or pump type to all EA888 variants. SSP 522, oil circuit.

F22 and F378 are pressure switches in the illustrated system; a switch state indicates whether its switching condition is met, not a continuous, calibrated oil pressure measurement. Stage request, actuator command and actual gallery pressure must be treated separately. F447 concerns the separate piston-cooling gallery: see piston cooling jet control.

Example control definitions

The following SC8S5031 ENLU setpoint definitions identify stage selection and conditions, not universal pressure targets in bar:

  • id_poil_h_pump_oil_el_maf_sp, id_poil_h_pump_oil_el_maf_sp_2 and id_poil_h_pump_oil_el_maf_sp_3 are high-stage request maps against n_32 engine speed and requested air mass maf_stk_sp_tqi in mg/stroke. Each has a 0–1 output in this reference. The active map and other logic require verification.
  • id_poil_h_pump_oil_el_maf_grd is another high-stage request map against requested air mass and its gradient; it is not an oil pressure sensor curve.
  • c_n_32_poil_h_pump_oil_el and c_n_32_poil_l_pump_oil_el are speed thresholds for switching high and low stages. c_t_pump_oil_h_max and c_t_pump_oil_l_max are hold-time calibrations; verify the full selector and timing logic.
  • lc_toil_pump_el_swi selects measured versus modelled oil temperature; lc_state_tco_toil_pump_oil_sp selects coolant versus oil temperature for the high-stage map-selection path. Their descriptions do not specify a general-purpose pressure increase.

Warnings and fault responses

The oil-pressure diagnostic definitions list ip_t_dly_err_poil_n_toil_clc_h and ip_t_dly_err_poil_n_toil_clc_l: delays in seconds before the high- and low-switch error symptoms are activated while the respective diagnostic condition is active, against calculated oil temperature and engine speed. These are not delays that enable the diagnostic itself. The separate ip_t_dly_poil_n_toil_clc_h and ip_t_dly_poil_n_toil_clc_l are labelled warning and diagnostic-result debounce delays in the same reference. These are diagnostic timing maps, not pressure-control maps. The TQSP reference describes ip_tq_pow_max_poil_plaus as a torque-limit curve versus speed for an implausible oil-pressure stage. A request for a stage or an absence of a fault does not establish adequate lubrication. Maintain fault monitoring and protective limits.

Practical diagnosis and tuning context

  1. Record exact engine, ECU software, oil specification and condition, fault codes, freeze-frame data and temperature. Check the correct service information and baseline before assessing calibration changes.
  2. Compare available stage request and pressure-switch states with speed, load and oil temperature. Switch state and request are not continuous pressure readings, and channel availability or polarity depends on the tool and software.
  3. If actual pressure is in doubt, use the manufacturer-specified test port, gauge, oil temperature and rpm procedure, and compare with specifications for the exact engine. Investigate oil level, oil condition, electrical or hydraulic faults, restrictions and mechanical wear before attributing a problem to the ECU map.
  4. A low oil-pressure warning calls for stopping the engine and following the vehicle's service procedure. Do not suppress the warning or assume a higher stage request repairs a worn or obstructed oil system.

Related: piston cooling jet control · turbocharger protection · tuning and log diagnosis.

For phaser movement-control maps, holding PWM and deviation-learning diagnostics, see Simos 18 cam phaser control and holding PWM adaptation.

For measured, modelled and substituted oil-temperature signals and their calibration examples, see Simos 18 oil temperature sensing and modelling.