The MCP is a six-speed automated manual, designed as one rather than converted from a manual gearbox the way the Sensodrive MA was. The stated capacity is 270 N·m. On the C4 with the DV6TED4, the engine’s maximum torque is given as 240 N·m, so both figures exist and the gearbox capacity is the higher one. Overall length is 390 mm and the weight is 50 kg with oil and without the clutch. It accepts a dual-mass flywheel. The shift hardware is a Magneti Marelli electro-hydraulic unit, and the stated launch application is the C4 DV6TED4. Ratio staging is 5.94.
| Gear | Teeth | Ratio |
|---|---|---|
| 1 | 13/46 | 3.538 |
| 2 | 25/48 | 1.920 |
| 3 | 31/41 | 1.323 |
| 4 | 40/39 | 0.975 |
| 5 | 46/35 | 0.761 |
| 6 | 52/31 | 0.596 |
| Reverse | 13/43 | 3.308 |
| Final drive | 19/71 | 3.737 |
The ratios are the tooth counts divided through. Staging of 5.94 is the span from 1st to 6th.
For the broader operating principle and other manufacturers’ related systems, see automated manual clutch and gearshift control and BMW SMG, Ferrari F1, Maserati Cambiocorsa and Fiat systems. Do not transfer the MCP’s measurements or procedures to those systems.
Gearbox
Two casings, a gearbox casing and a clutch casing, plus a rear cover, keep the unit short enough for the selector to fit on the front face. Internally there are two shafts and a half shaft for reverse. The reverse pinion sits between bearings to cut reverse noise. The differential is riveted and cannot be overhauled. The primary shaft, secondary shaft, reverse shaft, synchros, internal selectors, lubrication and bearings can.
Forks are mechanically welded, with moulded plastic pads. The 3rd/4th fork slides on the 1st/2nd shaft. Permaglide bushes are used on every shaft except reverse. The reverse fork is stamped, carries moulded plastic bearings, and includes the indent. Synchros are a single cone for 1st on the secondary shaft, a triple cone for 2nd on the secondary shaft, and single cones for 3rd to 6th on the primary shaft. Reverse has no synchro.
Lubrication is by splash, in a front circuit and a rear circuit. The oil is 75W80. It is drained at a drain plug and refilled through the breather, which is also the filler. There is no level check. The second fill is 1.8 litres. A first-fill quantity is not stated. This oil is not the oil in the hydraulic selector.
The input-speed sensor is inductive, two wires, on top of the gearbox, and it reads the reverse-gear teeth. Frequency and amplitude both rise with speed. Resistance is 770 to 810 ohms. The ECU needs this speed to command the shift.
The S-cam and the clutch
The selector is an electro-hydraulic S-cam on the front of the gearbox. The mechatronic block contains the valves, the ECU and the sensors. In the block are an electric hydraulic pump, a pressure sensor, two Hall position sensors on the S-cam (selection and engagement), a proportional clutch valve feeding the concentric slave cylinder, two proportional shift valves, and an on/off valve that applies the S-cam brake. Valve and pump-motor resistance is under 10 ohms. The valve measurement requires the ECU protection cover to be removed, because a metallic track joins the ECU to the valves and the pressure sensor. A test harness cannot see those parts.
A shift along the same selection axis, such as 1st to 2nd, leaves the S-cam brake released. The selector shaft moves sideways and the S-cam rotates with it. A shift across the gate, such as 2nd to 3rd, applies the brake. The shaft still moves sideways, the S-cam cannot rotate, and the pin is forced along the S-cam profile so the shaft turns. On the conical face, zero pressure is brake released and any other pressure is brake applied.
During the move, position is closed-loop. During synchronisation, the effort is open-loop.
The hydraulic fluid is Selenia CS Speed, parts reference 9979 A4, supplied in a 1 litre container. System capacity is just under 1 litre, and the concentric slave cylinder uses the same oil. The accumulator holds 37 to 49 bar. That pressure is exhausted with the diagnostic tool before the clutch bearing, the ECU, a valve, the accumulator, the pump or the electro-hydraulic assembly is opened. After refitting, the system is pressurised and bled.
The concentric slave cylinder is a composite thrust bearing with a steel guide tube and a passive position sensor. The ECU supplies a triangular signal to the primary. The secondary returns a square wave. Primary resistance is 30 to 40 ohms and secondary resistance is 20 to 30 ohms. One fixing screw holds it. The Hall sensors on the S-cam have no resistance measurement: supply is 5 V and the position signal is 0 to 5 V. The pressure sensor is the same kind of 5 V, 0 to 5 V signal.
The shift and the laws
The driver has manual and automatic. In automatic a shift can be forced for one change. The sequence is: the request is accepted, the ECU takes engine control and starts to open the clutch, engine torque is reduced as the clutch opens, and with the clutch open the selector disengages, selects, synchronises and engages. The clutch then closes and torque is restored against a comfort target. When the clutch is shut, engine control goes back to the driver.
Hyper-shift is the sports shift in manual, and it can skip gears. A standing-start mode, with a sprint start and a high-performance mode, is provided. The thresholds sit in the calibration. The gearbox also contributes to an anti-roll-back function. Hill assist, a later vehicle function, has the ESP hold brake pressure for 2 seconds after the driver releases the brake to press the accelerator on an uphill stop.
Automatic gear choice uses load, urban driving, a slippery surface, warm-up, an economical style, a sportier style and kick-down. The laws are Eco for urban economy, Norm as four laws from the conditions and the style, Snow as four laws, and Vsr for cruise control and the speed limiter. The sport button is read in the BSI, not on the gearbox-ECU parameter screen.
ECU
The ECU is the CFC300P. The calibration is downloaded. The gate and the bite point are initialised rather than edited. Diagnostics are on CAN. Two supplies are fitted: one direct from the battery and one from a relay controlled by the BSM. The ECU earths through the metallic link that also joins it to the valves. Two connectors are fitted, one towards the vehicle and one towards the hydraulic block. The labels 28V NR and 12V appear against those connectors and are connector identities, not supply voltages.
Starting is authorised by the ECU pulling a start-lock line to the BSM down to 0 V. The BSI and the engine ECU diagnose that line. The gearbox ECU stores no fault code for it. The main brake signal arrives by wire and a redundant brake signal arrives on CAN. A remote wake-up comes from the BSI.
The steering-wheel paddles are resistance switches of the Sensodrive type. Released resistance is 900 ohms to 1.3 kΩ. Active resistance is 150 to 250 ohms. The gear selector is the full-CAN Sensodrive type, externally supplied, so its resistance cannot be measured. Actuator position is Hall-effect.
In the fault lists, CO is an open circuit, CC+ is a short to positive and CC− is a short to earth. A few codes are used for two different faults. The parameter that is implausible is what separates them.
| Item | Codes | Check |
|---|---|---|
| Paddles | P1752 CC−, P1750 open or CC+, P1837 coherence | 900 Ω–1.3 kΩ released, 150–250 Ω active |
| Gear selector | P1708 CC−, P1716 open or CC+, P1718 and P1719 coherence | Voltage against the reference curve. Resistance cannot be measured. P1708 is also used as a brake-signal coherence code. |
| Input speed | P1738 open, CC+ or CC−, P1739 no signal, P1705 coherence | 770–810 Ω, sinusoidal voltage |
| Clutch-sensor primary | P1711 open or CC+, P1713 CC− | 30–40 Ω |
| Clutch-sensor secondary | P0808 open or CC+, P0807 CC− | 20–30 Ω |
| Shift-axis position | P1724 open or CC+, P1726 CC−, P1731 coherence | 5 V supply, 0–5 V signal. P1726 is also used for a vehicle-speed coherence fault. |
| Selection-axis position | P1732 open or CC+, P1734 CC−, P1733 coherence | Same 5 V signal |
| Position-sensor supply | P1587 CC+, P1586 CC− | Shared supply |
| Shift valve 1 | P0926 CC−, P0925 open or CC+, P0927 CC+, P0924 open | Under 10 Ω. P0925 is also used when a gear does not engage. |
| Shift valve 2 | P0922 CC−, P0921 open or CC+, P0928 CC+, P0920 open | Under 10 Ω |
| S-cam brake valve | P1764 CC−, P1772 open or CC+, P1765 CC+, P1766 open | Under 10 Ω |
| Clutch valve | P0902 CC−, P0901 open or CC+, P0900 open, P0903 CC+ | Under 10 Ω |
| Oil pressure | P0840 open or CC+, P0842 CC−, P0841 coherence. Supply P1590 CC+, P1589 CC− | 5 V, 0–5 V |
| Pump motor | P0947, P0948, P0945 CC+ | Under 10 Ω |
| Brake signal | P0573 open, plus P1708, P0556, P0559 as coherence | Brake-lamp switch, its link through the BSI and the engine ECU, and the switch fuses |
| Wake-up | U2000 to U2003 | Line state, and whether the ECU is awake |
| ECU supply | P0561 and P0563 open, P0562 | Supply voltage |
| Initialisation | P1800 gearbox, P0949 clutch | Investigate why initialisation failed or was incomplete, then use the applicable repair and setup procedure. |
| Power-latch | P1702 | ECU shutdown |
| ECU internal | P0603, P0604, P0605, P0606, P0608, P0609, P0613, P0634, P1621 | |
| Network | U1113 ABS, U1118 BSI, U1108 engine, U1003 CAN, U1000 communication among the other ECUs | |
| Clutch over-temperature | P0811 | Calculated temperature. No degree threshold is given. |
| Pump over-temperature | P0942, P0943 | Calculated |
| Oil-pressure leak | P0868, P2712 | |
| Accumulator discharged | P0944 | |
| Selection | P0896, P1767 selection problem, P1749 gear will not stay engaged, P0919 will not disengage, P0925 will not engage, P1701 incorrect gear | |
| Vehicle-speed coherence | P1726, P1830 |
C4 MCP clutch-position check faults: The reproduced Citroën C4 I MCP repair and diagnosis information lists P1712 for a clutch-actuator position signal fault and P1755 / P2785 for clutch-actuator position checking. It separately lists P1711 / P1713 for the primary sensor circuit and P0807 / P0808 for the secondary circuit. Save the full fault descriptions and available operating context, including supply voltage and requested and reported gear, before testing the applicable feedback and actuator circuits. None of these labels proves that the actuator, sensor or clutch requires replacement. Confirm the actual C4 gearbox, controller and current diagnostic tree before applying the example.
Fault-code comparisons on other MCP vehicles
Codes are controller-specific. A reproduced Citroën C5 II MCP diagnostic table describes P1755 as a clutch-actuator position coherence fault; it does not identify a failed part. Separately, a Peugeot 3008 I MCP variant 2 table lists P1843 for excessive gearbox-ECU supply-voltage drop during restart. These examples are not proof that either definition applies to the C4 controller discussed here. Record the full code description and conditions and use the current fault tree for the identified vehicle.
Downgraded modes
The safety aim is to stop an unexpected pull-away. Gears are disengaged if the clutch might re-engage during a hydraulic failure. Pull-away is forbidden when the intended direction cannot be determined. The engine can be stopped as an emergency measure. The exact clutch-detection condition for that stop is ambiguous, so it is not a procedure to copy. Availability is kept where it can be. Failed sensors put the actuators into open loop, so a gear can still be selected and the shift takes longer. The engine can still be started in almost every downgraded mode, so the cabin can still be heated or cooled. The highest gear is limited to 3rd, which is deliberate. If the lever fails, shifts, neutral and reverse remain available from the paddles. The pump has thermal protection if the gearbox is abused.
Error mode prohibits every new shift and finishes a shift already in progress if it can. Stationary in 3rd, 4th, 5th or 6th, pull-away is forbidden until the ignition has been cycled, or until the fault has gone and a shift is requested. In 1st or 2nd, a request for neutral or reverse from the lever forbids pull-away until the fault has gone and a shift is requested. With the engine stopped, the brake applied, a gear engaged and no shift in progress, a neutral request from the selector opens the clutch and forces a mechanical neutral.
Limp-home forces manual mode, allows every downshift, limits the highest gear to 3rd, and still allows neutral and reverse. Prohibited-shift mode blocks new shifts, finishes one already in progress, and at idle, while creeping or when pulling away, opens the clutch and imposes neutral. The gearbox lamp, the malfunction indicator, or both, may light.
If a controlling actuator has failed and the car has stalled in gear, there is no external way to select neutral. The recovery is to lift the front wheels. On Sensodrive the selector can still be put in N.
Initialisation and removal
The diagnostic tool initialises the gate and the clutch bite point, bleeds the slave-cylinder circuit, depressurises and repressurises the accumulator, and reads and writes counters for clutch cycles, gear engagements, paddle commands, the selector, the pump motor and the shifts made in the performance mode. A fault naming an initialisation does not prove that repeating it will repair the cause. Record faults and conditions first, check the vehicle-specific prerequisites and underlying mechanical, hydraulic and electrical faults, then complete the prescribed setup after repair.
If the tool cannot talk to the ECU, the supply is checked first: fuses, earths, battery and wiring. Faults are then read. Actuator tests and parameters are used to confirm them. Under the valve cover, the metallic track between the ECU and the valves is checked before the sensor. The rest of the system is then the harness, the resistances and the 5 V signals above, and the ECU supply and earth.
The joint between the ECU and the valves will accept the ECU being removed and refitted once. After that the ECU is replaced. Four M6 threaded studs, made up as guides, are used because the fit of the terminals is tight enough to bend a pin. An electrovalve-terminal checking tool is used before the ECU is refitted. The gearbox itself comes out with the front subframe and the subframe extension. A support handle is used, because the fluid reservoir is not strong enough to hold the gearbox, and because sitting the electro-pump on the floor damages it.
For separate city-car examples, see Peugeot 108 and Citroën C1 ETG operation and diagnosis. The handbook examples do not establish interchangeable actuator, fluid or learning procedures with this gearbox.