Tuning Wiki

Maserati describes the MC20 as using an eight-speed dual-clutch transmission. Its M240 diagnostic information is a separate application from the earlier Maserati Cambiocorsa single-clutch automated manual and the GranTurismo 6HP26 torque-converter automatic. Identify the actual car, market, model year, transmission and dual-clutch transmission module (DCTM) software before diagnosing it. Maserati: MC20 specification.

Pressure, shift and park fault examples

Maserati North America's diagnostic sheet MAS005093 / DS 26-05, 9 April 2026 addresses M240 MC20 and MC20 Cielo from model year 2022 with a transmission warning and one or more of the listed DCTM faults. It supersedes the 2025 MAS004558 DS 25-03 sheet, which had a narrower model-year restriction. Check the latest service information and actual software; neither bulletin proves that every MC20 has the fault.

Examples in MAS005093Diagnostic distinction
Type 1: P0746/P0747 pressure-control solenoid A; P0867/P0868/P0869 pressure; P2853–P2856 clutch pressure charge/dischargeThese describe different monitored conditions in the bulletin's first group. A stored code is not by itself proof of a failed solenoid or mechatronic assembly. The sheet gives a separate branch if a documented fault recurs after its specified procedure.
Type 2: P07E4 unable to engage Park; P07E6 stuck in Park; P284D–P2850 and P286A unrequested shift-fork movementThe second group also includes individual stuck-in-gear and unable-to-engage-gear codes. For recurring type 2 codes, the sheet directs a pressure-parameter recording with stated temperature, engine, gear and sampling conditions. Follow the complete applicable plan; one code does not establish which hardware is defective.

For its specified fault cases Maserati describes a DCTM Service Fast Learn routine to bleed and readapt the hydraulic system where valve sticking is suspected. It is a controlled workshop function, not a universal reset: record all codes and parameters first, confirm the exact vehicle and DCTM version, and follow current manufacturer instructions and safety conditions. For MY22 the 2026 sheet requires a software identity check; some listed versions may require an update before the routine, while unlisted versions cannot use it under that procedure. Do not assume all MY22 cars can run the function or program a module based solely on model year.

Oil leak and separate software campaigns

Maserati's circular MAS004426 / MCL 24-56 reports a small number of MC20 transmission-oil leaks at the differential cover, potentially involving a pinched O-ring or damaged internal oil tubes. It describes a parts-level service option for that particular leak; inspect and identify the actual source rather than assuming every transmission fluid leak has the same cause or requires a complete gearbox. Consult the current manufacturer procedure, correct parts and service support.

In service campaign 468 / MAS002970, Maserati identifies a limited listed group of MC20 cars whose DCTM adaptive parameters could produce erroneous gearbox or poor-performance warning lights. The diagnostic command named “Replace Gearbox” in that historical campaign was used to write identification data; the document explicitly says the gearbox was not physically replaced. The command name is not an instruction to run it for other faults.

Separately, service campaign 522 / MAS003188 describes a possible stuck-on gear selection and engine or transmission warning lights on a listed MC20 population, addressed by updating DCTM diagnosis calibration. These were model- and VIN-scoped service campaigns, not proof that a particular car is affected or that every warning has a software cause. Check VIN, completed actions and current manufacturer instructions before programming.

Evidence-led workshop sequence

  1. Record VIN, market, model year, DCTM software and previous service work. Preserve complete vehicle faults, freeze-frame data, warnings, requested and indicated gear, temperature and conditions before clearing.
  2. Differentiate an interlock or selector request, pressure-feedback concern, actual external leak, clutch or gear engagement issue, and software configuration using the specific fault plan. Use the correct diagnostic equipment and record measured states under the conditions the manufacturer specifies.
  3. Where the applicable sheet calls for programming, an active learning operation, oil and filter work, or manufacturer technical support, use current official instructions. A learned value, warning lamp or DTC alone is not a replacement-parts verdict.
  4. Secure the vehicle and follow the model-specific workshop and road-test precautions. Verify the original complaint and fault status after the prescribed repair.

See Maserati MC20 models and engine, Ferrari California dual-clutch gearbox and the electronic gearbox index. Fault codes and service functions should not be transferred between these applications.