This guide uses Maserati Technical Service Operations diagnostic sheet MAS002929 / BOL 24-06, dated 21 February 2024, reproduced by OEMDTC. The Maserati bulletin is also available directly through NHTSA. The bulletin's diagnosis scope is Quattroporte M139 and GranTurismo M145 with the robotised Cambiocorsa/F1 transmission. Its table discusses additional models and versions, but the diagnostic instructions below should not automatically be transferred to an M138, a Ferrari, a torque-converter Quattroporte or a dual-clutch Maserati. Confirm VIN, fitted transmission, NCR controller, software and current service information.
Construction and operating evidence
Cambiocorsa uses an electronically controlled clutch and gear-changing actuators on a mechanical transmission. The diagnostic sheet refers to an NCR gearbox control unit, clutch position, selection and engagement potentiometer positions, hydraulic actuation and solenoid leakage parameters. A driver may request shifts without operating a clutch pedal. It is not enough to identify a car by the badge: an automatic-shift mode, a twin-plate friction clutch and a dual-clutch transmission are different ideas. See F1-style gearbox overview.
GranTurismo MC Stradale example
The supplied Maserati Academy GranTurismo MC Stradale training document (local PDF page 25) identifies the M145 MC Stradale as an electrohydraulically actuated six-speed mechanical gearbox with a dry twin-plate clutch. Pages 30–31 describe a redesigned actuator compared with the earlier Quattroporte DuoSelect and GranTurismo S illustrations; service assumptions about component interchangeability are therefore unsafe without part identification.
Academy pages 32–33 describe SOFAST IV/Superfast 2 learning and a service-operation matrix for this model. This older training material must be read with the later, specifically applicable 2024 MAS002929 warning below: use the current repair information and never substitute the prohibited NCR “Self-Learning (All)” command for the separately specified gear-structure learning. The Academy document is a local source and is not published here.
Critical learning warning
For the NCR diagnostic procedure covered by MAS002929, Maserati explicitly warns not to run the active diagnosis named “Self-Learning (All)”: it states that doing so permanently damages the NCR ECU and can require ECU replacement. The bulletin distinguishes that command from the specified gear-structure self-learning and other individual procedures. Names can be similar; verify the tool screen, vehicle applicability and current manufacturer instructions before executing any active function. Do not use the full procedure as a generic reset. Maserati MAS002929, sections A and F.
The same bulletin says that the active clutch-configuration command stores the current position as the new-clutch reference and must only be performed after installing a new clutch. Its prescribed TCU replacement procedures differ and may require preserving the existing reference. A scan tool's clutch-wear percentage is calculated from stored and measured positions; an incorrect or zero reference can make the percentage nonsensical. Record the raw reference and measured values as well as the percentage, and assess mechanical condition before drawing conclusions.
PIS (Punto Incipiente Slittamento), also called the kiss point, is the start-of-slip setting. Maserati lists different values for different model/system versions and a sequenced learning process. The supplied 2006–2012 Maserati M139 Quattroporte Shop Manual (local PDF page 1094) also shows that the kiss-point routine reports a calculated point and the stored point, illustrating the need to keep the two distinct. The values and procedures are not interchangeable; use the correct factory document and diagnostic equipment rather than copying another car's setting or using calibration to conceal worn or faulty hardware. Maserati MAS002929, sections B and F.
Symptoms and diagnosis
- Wrong or refused shifts / P1770: MAS002929 gives P1770 as an example of incorrect engagement for its covered NCR application. It asks technicians to reproduce the concern, check for F1 hydraulic leaks, save dynamic parameters, examine gearbox oil condition and compare the gear-position grid with cold and warm data. The code does not uniquely identify a failed actuator.
- Heat-related changes: the bulletin asks for clutch solenoid leakage parameters with the clutch engaged and not engaged, comparing cold and warm conditions. Follow its documented measurement method and limits for the identified system; do not apply one leakage limit to all F1 gearboxes.
- DEIS “Unexpected value (6)”: the bulletin identifies clutch or thrust-bearing condition and, in some cases, hydraulic actuation as avenues for investigation. It directs inspection of the specified filters and clutch friction condition. The message alone does not establish which part needs replacement.
- Noise during slow uphill take-up: Maserati describes a particular twin-plate clutch noise in a referenced demonstration, especially when cold, and says prolonged slip and heat can intensify it. A different noise, a new symptom or mechanical damage still requires inspection; the description is not permission to dismiss every rattle.
These examples come from MAS002929, sections D–G. Record fault codes and freeze-frame information before clearing them. Check the power supply, connections, vehicle-specific input states, fluid condition and leaks, and compare requested and actual actuator position using manufacturer guidance. A fluid leak, pressure loss, failed shift or wear percentage is evidence to investigate, not a diagnosis by itself.
After repair
Do not mix the hydraulic actuator fluid with gearbox lubricant or assume a fluid specification from another model. Follow the applicable manufacturer's instructions for bleeding, configuration, the individual learning operations and verification. Capture the original complaint and parameters before and after the repair; where the bulletin calls for cold and warm gear-grid data, maintain the same conditions for comparison. The system may retain hydraulic pressure and diagnostic commands can move actuators: follow the current workshop precautions.
For the earlier M138 clutch, see M138 Cambiocorsa clutch service and diagnosis: the supplied Maserati Coupé workshop manual describes version-specific balancing and SD2 setup. Its values must not be applied to M139 or M145 merely because the systems share a name. Related: automated manual clutch and gearshift control, clutch types and operation and flywheel and clutch-area noise.
Related example: Ferrari 360 F1 diagnostics; diagnostic procedures and settings must remain vehicle-specific.