Tuning Wiki
Browse Maserati

The supplied Maserati Coupé Workshop Manual describes manual GT and Cambiocorsa clutch variants and identifies the automated gearbox diagnostic application as M138 Marelli Gearbox. This page extracts selected service and diagnostic distinctions from that local document, PDF pp. 693–697 and 710–733. It does not establish the same clutch, values, balancing method or service functions for M139, M145 or every M138 revision. Verify the VIN, clutch component revision, gearbox and controller software against current Maserati repair information. The supplied manual is a local source and is not published here.

An assembly, not just a friction disc

The workshop manual's removal section instructs technicians to record the relative positions of the clutch pack and associated engine/flywheel components. In the illustrated assembly, it identifies particular clutch screws and spacers as counterweights. Its refitting section also identifies marked maximum-unbalance points and a required relationship between a replacement clutch disc and flywheel. These instructions show why hardware orientation, existing marks and the exact balancing method matter: do not assume every fastener is interchangeable or independently zero-balance the assembly. Source: supplied Maserati Coupé Workshop Manual, PDF pp. 693–697.

The same manual gives different procedures for different clutch-component generations and includes dedicated balancing equipment and the SD2 diagnostic system. Check the component version and prescribed workshop procedure rather than transferring a balancing method from another Maserati or a conventional single-mass replacement. Source: PDF pp. 710–720 and 722–731.

Cambiocorsa clutch reference and engagement

For the specific clutch replacement/setup examples, the manual selects the M138 Marelli gearbox on SD2, records an auto-set closed-clutch position and stores a new-clutch reference. It identifies different clutch-disc or software combinations in separate procedure sections. The manual also describes setting and evaluating the PIS or touch point and checking clutch-solenoid leakage after the specified conditions. Source: PDF pp. 721 and 731. The stored new-clutch reference, current measured position, PIS and calculated wear are related but different pieces of information.

Record the existing values and service history before replacing parts or starting a diagnostic function. Do not initialise a new-clutch reference on a worn clutch merely to alter its displayed wear, or copy a touch-point value from a different car, clutch revision or controller. Maserati's later MAS002929 bulletin explicitly limits its new-clutch reference instruction and prohibits a particular NCR “Self-Learning (All)” command for its covered M139/M145 diagnostic procedure. That bulletin is not an M138 procedure; use it to understand why similarly named functions and vehicle scope must be checked, not as a universal menu map.

If take-up or shifts deteriorate

  1. Record the control unit and software identification, clutch part and installation history, complaint, selected mode, temperature, gear and whether it occurs only during pull-away or during a particular shift. Preserve faults before clearing them.
  2. With a compatible tool, compare the reported clutch reference and position with command, engine and gearbox speeds, selected gear and the applicable actuator states. Consider wear or contamination, incorrect reference, clutch release or position feedback, hydraulic pressure and power supply; no one displayed number proves the cause.
  3. Inspect the hardware and hydraulic system according to the applicable factory diagnostic plan. The local manual describes a clutch-bleed program using the SD2 after relevant component work, with a separate reservoir-level check; use the current procedure and specified fluid, and do not reuse expelled fluid. Source: PDF pp. 732–733.
  4. After an identified repair, follow the correct version-specific balancing, setup, bleeding and verification procedures and test the reported condition. The hydraulic system can remain pressurised and diagnostic operations can move actuators; follow current isolation and depressurisation instructions.

When the hydraulic pump does not run

The Maserati 4200 workshop manual's Cambiocorsa wiring key identifies a dedicated F1 pump relay (N005), pump motor (P030), pump earth (C018), gearbox-controller earth (C014) and solenoid-valve earth (C019). With a pump-running or pressure complaint, use the correct diagram for the vehicle to trace the pump command, loaded electrical supply and earth, relay and pump circuit; also investigate hydraulic leakage and pressure feedback as the applicable diagnostic plan directs. These identifiers locate circuit elements in that manual, not universal fuse positions or a diagnosis of a failed part. Maserati 4200 workshop manual, Cambiocorsa electrical component key.

See M139/M145 Cambiocorsa diagnosis, flywheel and clutch fitment and balance, clutch types and the F1-style gearbox index.