An ignition coil is a transformer that turns a primary current of a few amps at battery voltage into the 25 to 45 kV needed to break down a spark-plug gap under compression. Every design does the same electrical job. They differ in how many plugs one coil serves, whether high-tension leads are used, how the windings are insulated and cooled, and whether the switching transistor (the igniter or output stage) is inside the coil or in the engine controller. The last point matters most when a coil is reused on another engine or driven by a standalone ECU: a "dumb" coil connected straight to a logic-level ECU output does not fire, and a "smart" coil connected to a high-current driver can be destroyed.
This page classifies the designs and explains how to identify them. Individual part numbers, pinouts and published dwell figures are in the databases: European and US production ignition coils, Japanese production ignition coils and Bosch Motorsport ignition coils. How a coil is charged and timed is on ignition coils and coil-on-plug basics and ignition systems and spark plugs; the spark angle is on ignition tuning.
Common construction
All automotive inductive coils have a primary winding of a few hundred turns of heavy wire, a secondary of many thousands of turns of fine wire, a laminated iron core, and an insulating fill. BERU's technical information gives 100 to 250 primary turns of about 0.75 mm wire and 10,000 to 25,000 secondary turns of about 0.063 mm wire, primary currents of 6 to 20 A, secondary voltages of 25 to 45 kV and spark energies of 10 to 60 mJ on conventional engines (up to about 140 mJ on some direct-injection engines). Modern coils are cast in two-component epoxy resin; older canister coils were filled with oil, and Bosch later replaced the oil with asphalt compound.
Switching the primary on also induces a small secondary voltage, about 1.5 kV according to BERU, which can fire the plug early (the make spark). Each layout handles it differently: a distributor's rotor gap blocks it; in a wasted-spark coil the two plugs in series share it; a single-spark coil-on-plug needs a high-voltage diode in the secondary. Reversing the primary terminals of a diode-equipped coil can destroy that diode, and the diode also prevents the secondary resistance from being read with an ordinary ohmmeter.
Design types
| Design | Plugs per coil | HT leads | Igniter | Typical era and examples |
|---|---|---|---|---|
| Canister (can) coil | All, via distributor | Yes | Points or separate module | Points and early electronic distributor systems; now mainly classic cars |
| Epoxy block coil for a distributor | All, via distributor | Yes | Separate module, later sometimes on the coil | 1980s–1990s electronic and mapped distributor ignition; GM remote HEI E-core coil |
| Coil in or on the distributor | All | Plug leads only | Usually in the distributor | GM HEI (coil in cap); Toyota IIA (4A-FE, 7A-FE); Honda distributors with side-mounted igniter |
| Wasted-spark (double-spark) pack | Two, in series | Usually | Either | 1980s–2000s distributorless: GM C3I/DIS, Ford EDIS, Bosch and BERU 4-tower blocks, Subaru EJ |
| Coil rail or cassette | One per output | No | Either | Three- and four-cylinder engines: Opel/GM Ecotec rail, VAG Eldor rail, Saab Direct Ignition |
| Pencil (stick, rod) coil-on-plug | One | No | Either | From the mid-1990s: BMW M52/M54, VAG 1.8T and FSI, Toyota ZZ, Honda K |
| Compact (plug-top) coil-on-plug | One | No | Either | Coil body above the well: Bosch compact coils, including the Bosch Motorsport C75 and C90i |
| Coil-near-plug | One | Short lead | Either | GM LS family |
| Capacitor-discharge (CDI) coil | Depends on system | Depends | CDI box or cassette | Saab Direct Ignition, MSD-type boxes, motorcycles and small engines |
Canister coils and ballast resistors
The canister coil is a cylindrical metal can with an external high-tension tower, the windings wrapped round a central iron core inside a magnetic shell, and the space filled with oil or a casting compound. It serves every cylinder through a rotating distributor. The two low-tension terminals follow the DIN numbering used on most European diagrams: terminal 15 is the switched supply and terminal 1 is the primary switched to earth by the points or an ignition module. Hella's reference values for distributor coils are 0.5 to 2.0 Ω primary and 8 to 19 kΩ secondary.
Some coils for points ignition are designed for a lower running voltage and are fed through a ballast resistor, which is bypassed while cranking so the spark survives a sagging battery. No manufacturer description of the ballast values was found; workshop and owner reports put the running voltage at about 6 to 7 V and the coil primary at roughly 1 to 1.5 Ω. A ballast coil fed directly from 12 V overheats; a full-voltage coil left behind a ballast resistor gives a weak spark. Matching the coil to the resistor actually fitted is covered on ignition systems and spark plugs.
Epoxy block coils for distributors
Electronic and mapped distributor systems moved to dry, epoxy-cast coils with a closed or segmented core, smaller and better at shedding heat than a can. The switching stage was at first a separate module on the body or in the distributor; later units carry the output stage on the coil itself. BERU lists what an integrated stage allows: diagnosis, current limiting, thermal cut-off, short-circuit detection and, in some designs, an ion-current signal. The core geometry ("E-core") is described in parts catalogues but was not found in a manufacturer text.
Coils built into the distributor
Some systems put the coil in the distributor itself. GM's High Energy Ignition, used on North American GM engines from 1975 into the mid-1980s, mostly carried the coil in the distributor cap, with the module and pickup inside the distributor. Toyota's Integrated Ignition Assembly (IIA) combines the igniter and an open coil in the distributor on engines such as the 4A-FE and 7A-FE. Honda distributors of the D, B, F and H series bolt the igniter to the distributor body so that it sheds heat into the housing. Reported failures are the igniter's output transistor joints cracking from heat cycling, worn distributor bearings letting the rotor or reluctor rub, and a worn cap carbon button. Hondata's coil-pack retrofit for these distributors replaces the stock coil and igniter with an external coil.
Wasted-spark packs
A wasted-spark (double-spark) coil has one secondary winding with both ends brought out, feeding two plugs in series on cylinders 360 degrees apart. One plug fires on compression, the other on the exhaust stroke. The design needs no camshaft signal and only suits engines with an even number of cylinders. Because the plugs are in series, one fires with negative centre-electrode polarity and the other reversed; the reversed plug needs more voltage and wears on the opposite electrode. Trade sources disagree on how much more: Motor Age (2020) gives up to about 30 percent, while Motor (1999), followed on ignition systems and spark plugs, gives up to about 45 percent. Both are upper bounds that depend on gap, electrode wear and cylinder pressure, and no manufacturer figure settles the difference; either way, the reversed plug of each pair has the smaller voltage reserve. A broken lead can misfire both cylinders of the pair.
Wasted-spark hardware comes in several forms:
- Four-tower blocks. Two double-spark coils in one epoxy block, fired by two primary circuits. Bosch, BERU and Delphi made these for VAG, GM/Opel, PSA and Fiat four-cylinder engines. Hella also describes a "four-spark" coil with two primaries, one secondary and diode cascades.
- Modular packs on a base. GM's C3I/DIS (from the 1984 Buick 3.8 turbo) mounts coils on an ignition control module. On Type 1 the three coils are moulded into one housing with towers on both sides; on Type 2 all towers are on one side and each coil can be replaced on its own.
- Coil packs with a separate module. Ford EDIS uses a four-post pack (four cylinders), a six-post pack (V6) or two four-post packs (V8), driven by an EDIS module that holds the coil drivers and sets dwell.
- Hybrid coil-on-plug wasted spark. Some engines put one double-spark coil directly on one plug of a pair and run a lead to its partner; BERU gives the Mercedes M104 as an example. The Toyota 1JZ and 2JZ VVT-i engines (three coils, external igniter) and the Mitsubishi 4G63 in the Lancer Evolution IV to IX (two coils, internal igniters) use the same arrangement.
A wasted-spark coil fires once every crank revolution, twice as often as a sequential coil-on-plug, so a dwell table copied from a sequential coil overheats it. Converting a wasted-spark engine to sequential coil-on-plug also needs a camshaft reference.
Coil rails and cassettes
A rail or cassette houses several independent single-spark coils in one moulding that plugs directly onto a row of spark plugs, with one connector for the set. BERU notes they are common on three- and four-cylinder engines; BorgWarner supplies them in both single-spark and double-spark forms. Examples are the Opel/GM Ecotec 16-valve cassette (four dumb channels on a six-wire connector), the Eldor rail on VAG 06A 905 097/104 (four smart channels) and the Saab cassette on the 1.8 XE/Z18XE family. A rail is replaced as a unit when one channel fails, unless the coils inside are individually serviceable.
Coil-on-plug: pencil and compact coils
Coil-on-plug puts one coil directly on each plug with no lead. Bosch distinguishes the pencil coil, whose transformer sits inside the slim body down the plug well, from the compact coil, whose transformer sits in the head above the well. BERU also uses the names plug-shaft, rod and plug-top coil. Each coil fires once per engine cycle, so the controller needs a camshaft reference to know which cylinder is on compression, and dwell and timing can be trimmed per cylinder.
The parts that fail are mostly in the well rather than in the windings: heat cracking the body, the boot fusing to the plug insulator, carbon tracking down the boot, and water or oil in the well. BERU notes bodies cracked by over-tightening (15 N·m used where 6 N·m was specified). Swapping a coil to another cylinder and seeing whether the misfire follows it is the standard check.
Coil-near-plug
Where a head leaves no room for a coil in the well, a coil per cylinder is mounted nearby and connected to its plug by a short lead. The GM LS engines are the best-known example: their coils sit on brackets on the valve covers, and Haltech requires plug leads with a ferrule, without which the spark can arc to the coil bracket. The Toyota JZ engines are sometimes described as coil-near-plug, but Haltech's documentation separates them: the non-VVT-i 2JZ-GTE has six coil-on-plug units fired individually, while the VVT-i 1JZ and 2JZ have three coil-on-plug units, each also feeding its partner cylinder through a lead.
Capacitor-discharge coils
In an inductive coil the energy is stored in the coil's magnetic field during dwell (E = ½LI²; a 3.2 mH coil at 7 A holds about 78 mJ). In a capacitor-discharge system a converter charges a capacitor to several hundred volts, and the stored charge is dumped into a low-inductance coil primary at the firing point, so the coil carries significant current only during the discharge. Charge voltages quoted by makers are about 400 V for the Saab Direct Ignition cassette and 520 to 535 V for the MSD 6AL-2. A 2014 bench study by Goulart and co-authors measured a much shorter delay to breakdown and a far higher peak secondary current from CDI than from an inductive coil, using purpose-built low-inductance coils. CDI coils are not interchangeable with inductive coils of the same appearance.
Ion-sensing coils
An ion-sensing system uses the spark plug itself as a combustion sensor between sparks. Saab's Direct Ignition cassette on Trionic 7 applies about 80 V across the plug gap except during the spark; ionised combustion gas lets current flow, and detectors for cylinders 1+2 and 3+4 pass pulses to the ECU, which uses them for cam-phase recognition, misfire detection and knock detection. Trionic 8 coils apply about 120 V and return the ion signal on a dedicated pin to a separate detection module. Saab Direct Ignition was in series production from the 1988 Saab 9000, with the electronics in an oil-filled cassette. More on the plug as an ion sensor is on ignition systems and spark plugs.
Smart and dumb coils
A dumb (passive) coil has only windings. Something else, the ECU's internal driver, a separate igniter or a module, must switch the full primary current of several amps and absorb the 300 to 600 V flyback. A smart (active) coil has an integrated output stage, usually an IGBT or a dedicated ignition IC such as Bosch's BIP373 or BIP385, and is triggered by a logic-level signal of a few milliamps. Many smart coils also limit current and protect against overheating.
Getting this wrong is the most common coil fault on standalone conversions. A logic output of 10 to 20 mA cannot charge a dumb coil, so it does not spark. A high-current driver connected to a smart coil's logic input can overload the coil's input stage. Some smart coils, the GM LS family for example, can draw close to 10 A each, so the supply and fusing must be sized for the set. Bosch's own numbering appears to follow the pattern 0 221 504 xxx for coils without igniter and 0 221 604 xxx for the integrated-igniter versions (P35/P35-T, P65/P65-T), but that pattern is inferred from a few parts and is not a documented Bosch rule.
Identifying by pin count
| Pins | Usual meaning | Reliability |
|---|---|---|
| 2 | Dumb: battery supply and the switched primary earth | Reliable; Haltech states a 2-pin coil has no igniter |
| 3 (dumb) | Supply, switched primary, and a separate secondary or chassis earth | Common on Nissan S13/S14, BMW and early VAG 1.8T (058 905 105) coils |
| 3 (smart) | Supply, earth, logic trigger | Bosch P35-T and P65-T, PSA 1.6 THP. Three pins alone does not identify a smart coil |
| 4 | Smart: supply, power earth, signal earth or feedback, trigger | GM LS (A power earth, B signal earth, C trigger, D +12 V); VAG 06E/07K (1 +12 V, 2 earth, 3 trigger, 4 earth); Toyota (+B, IGT, IGF, earth). Haltech knows of no 4-pin single coil without an igniter |
| 4–6 on a pack or rail | Supply, earth and one trigger or primary per channel | Depends entirely on the part; check whether the channels are dumb or smart |
A resistance check helps. A dumb coil's primary measures a fraction of an ohm to about 1 Ω across its two primary pins; a smart coil's primary is not reachable, and Bosch lists the P65-T resistances as not measurable. Where the pin functions are not documented, the coil should be identified by part number before it is powered.
Toyota IGT and IGF
Toyota smart coils and external igniters use two signals. IGT is the ECU's 5 V trigger pulse: the coil charges while it is high and fires on the falling edge. IGF is the confirmation: the ECU holds a shared IGF line at 5 V and each igniter pulls it low when its coil has fired. A missing IGF pulse sets a misfire or igniter code and, on many Toyotas, the ECU cuts fuel to that cylinder. A standalone ECU that does not read IGF can ignore it, but a factory ECU used with a non-Toyota coil will see a missing IGF. On older Toyota external igniters a dwell-control circuit inside the igniter decides when primary current starts, so the IGT pulse width is not necessarily the coil's on-time (Motor magazine, quoting Toyota service text). Details by engine are on Japanese production ignition coils.
Resistance reference values
These are general reference ranges from maker technical texts; the figure for a particular coil is in its own data or service manual.
| Coil type | Primary | Secondary | Source |
|---|---|---|---|
| Distributor (cylinder) coils, transistor or mapped ignition | 0.5–2.0 Ω | 8–19 kΩ | Hella |
| Single- and double-spark coils, distributorless | 0.3–1.0 Ω | 8–15 kΩ | Hella |
| Current production coils (general) | 0.3–0.6 Ω | 5–20 kΩ | BERU |
| BERU 2×2 block (ZSE 003 example), each output pair | 4.0–6.0 kΩ at 20 °C | BERU | |
| GM C3I/DIS Type 1 / Type 2 | 0.35–1.50 Ω | 10–14 kΩ / 5–7 kΩ | Motor Age |
| Passive coil-on-plug (general) | 0.4–1.1 Ω | Import Service | |
| Smart coils | Not measurable through the connector | Bosch Motorsport, Toyota | |
A coil can pass a resistance check and still break down under cylinder pressure, so a resistance test only rules out an open or shorted winding. A running misfire test, a secondary waveform or swapping the coil is the stronger check; see spark and ignition testers and oscilloscopes.
Reusing coils on another engine
- Identify the drive type first. Confirm smart or dumb from the part number, not from appearance or pin count alone.
- Match the ignition mode. A wasted-spark ECU setting with sequential coils, or the reverse, fires the wrong cylinders or overworks the coils. Sequential needs a cam reference.
- Use the coil's own dwell. Published dwell figures depend on supply voltage and are specific to the coil; ECU makers' figures for the same coil sometimes differ, and the database pages note where they do.
- Check the trigger edge. Most smart coils charge while the input is high and fire on the falling edge. There are exceptions: Haltech specifies a rising edge for the Honda B-series igniter in the distributor, and MegaSquirt drives Ford EDIS with an inverted output. Haltech warns that the wrong edge setting can damage coils and the ECU.
- Size the supply. High-energy smart coils can draw up to about 10 A each; Haltech recommends separate fusing for each pair on VAG FSI coils at high power.
- Keep the secondary earth. Coils with a separate earth to the cylinder head must have it, or the spark finds its own path.
Not established
- A manufacturer description of E-core geometry, and of ballast-resistor coil values.
- Concrete production examples of leaded single-spark four-tower blocks (one coil per output, each fired separately).
- Production ion-sensing coils outside Saab.
Sources
- BERU (Federal-Mogul), Technical Information No. 07: All about ignition coils, printed 2 September 2013. Construction, winding figures, make spark, design types, resistance and fitting faults. Manufacturer technical text. Accessed 2026-11-19.
- Bosch Automotive Aftermarket, Ignition coils, modules, leads and spark plugs, brochure, about 2015. Canister, pencil and compact coils; asphalt fill. Manufacturer catalogue. Accessed 2026-11-19.
- Hella TechWorld, Ignition coil: checking, measuring, faults, undated, and Hella, Brief information: ignition coils, February 2022. Reference resistances, four-spark coil, integrated output stages. Manufacturer technical text. Accessed 2026-11-19.
- BorgWarner Aftermarket, Ignition coils, undated. Rails, pencil and plug-top coils with or without electronics. Manufacturer page. Accessed 2026-11-19.
- NGK Australia, Ignition coil: spark technology, undated. Manufacturer page. Accessed 2026-11-19.
- Bosch Motorsport, Basic information: ignition coils, 17 September 2018, and data sheets for the P65 and P65-T, January 2026. Naming, integrated stages, non-measurable resistance. Manufacturer documentation. Accessed 2026-11-19.
- Haltech, Do I need an external igniter module? and LS1 ignition coil, undated. Pin-count rules, LS pinout and lead ferrule. ECU-maker documentation. Accessed 2026-11-19.
- C. Nangle, GM DIS, Part I, FenderBender (originally Motor Age), 1 January 2020. C3I Type 1 and Type 2, resistances, polarity. Trade technical article. Accessed 2026-11-19.
- Motor, July 1999, distributorless ignition. Wasted-spark pairs and the higher reversed-polarity figure. Trade technical article. Accessed 2026-11-19.
- J. Linfert, Modifying a GM DIS ignition module for direct coil control, DIYAutoTune, December 2009. Module connections and applications. Tuning-vendor article. Accessed 2026-11-19.
- MSExtra, MS1/Extra ignition hardware manual, undated. Ford EDIS packs. Community ECU documentation. Accessed 2026-11-19.
- Automotive Tech Info, How to find Toyota ignition system faults fast, July 2021; J. Woods, Coil-on-plug ignition, Import Service, July 2000; J. Woods, "Conventional" Honda ignition, Import Service, December 1999. IGT/IGF, passive COP resistance, Honda igniters and failures. Trade technical articles. Accessed 2026-11-19.
- M. Warren, Driveability corner, MOTOR magazine, February 2007. IGT/IGF operation and igniter dwell control, quoting Toyota service text. Trade technical article. Accessed 2026-11-19.
- Haltech knowledge base, Honda/Acura B series engine, 2JZ/1JZ engine and VW/Audi FSI ignition coil, undated. Trigger edge, JZ coil layouts and supply current. ECU-maker documentation. Accessed 2026-11-19.
- Saab WIS, 9-3 Trionic T7 ignition discharge module; 9-3 Trionic T8 ionisation current measurement; 9-3 1.8 XE ignition coil unit. Manufacturer service text. Accessed 2026-11-19.
- L. Carley, How to diagnose and test an ignition coil, AA1Car, 2022. Failure modes. Technical article. Accessed 2026-11-19.
- B. S. Goulart et al., Technical evaluation of vehicle ignition systems, Acta Scientiarum Technology 36(4), 2014. Inductive and CDI bench comparison. Peer-reviewed. Accessed 2026-11-19.
- MSD, 6AL-2 ignition control installation instructions, part 6421, undated. CDI charge voltage and multi-spark. Manufacturer instructions. Accessed 2026-11-19.
- Hondata, Coil pack retrofit, undated. Vendor page. Accessed 2026-11-19.
- Wikipedia, High energy ignition and Saab Direct Ignition. Used for dates only. Accessed 2026-11-19.