Tuning Wiki

This page is a database of production ignition coils from Japanese makers (Toyota, Honda, Nissan, Mitsubishi, Subaru, Mazda), with a short section on Korean coils and motorcycle coils used in car conversions. For each coil it records the design, whether the igniter is inside the coil ("smart") or in a separate igniter or power transistor ("dumb"), the pinout, the trigger edge an ECU must use, and dwell where an ECU maker publishes one in text. Design types are explained on ignition coil types and designs; European and US coils are on European and US production ignition coils.

Application data comes mainly from Hitachi Astemo's 2024 replacement-coil catalogue, which lists Hitachi replacement numbers against Toyota, Honda, Nissan, Mitsubishi, Subaru and Mazda part numbers. A listing in that catalogue does not show that Hitachi made the original coil. Pinouts and ECU settings come mainly from Haltech's engine pages. Haltech publishes most of its dwell tables as images, so most coils here have no text dwell figure.

Many Japanese installations use a separate igniter or power transistor even with coil-on-plug, so a coil-on-plug layout is not proof of a smart coil. Haltech warns on several engines that selecting the wrong edge or charge mode will damage the coil or the ECU.

Summary

Part number (Hitachi replacement)EngineDesignIgniterPinsEdge
Toyota 90919-022052JZ-GTE, 2JZ-GE non-VVT-i (Supra JZA80, 1993–98)COP, six per engineExternal3Falling
Toyota 90919-02216 (U22T01)1JZ, 2JZ VVT-iCOP plus lead to partner, three per engineExternal2Falling
Toyota 90919-02197 (U12T02)3S-GE, 3S-GTE (SW20); early JZDistributor coilExternal2Falling
Toyota 90919-02239, -02240, -02243, -022621ZZ-FE, 3S-GE (Altezza), 3S-GTE gen 4/5, othersPencil COPIntegrated4 (IGT/IGF)Falling
Toyota 2ZZ-GE coil2ZZ-GEPencil COPIntegrated4 (IGT/IGF)Falling
Honda 30520-PNA-007, -RRA-007, -PCX-007 (U14H01)K20A, K24A, F20CPencil COPIntegrated3Falling
Honda 30510-PT2-006 (U12H06) and B/D-series unitsH22A, B and D seriesCoil and igniter in distributorIn distributorDistributor plugRising
Nissan 22448-50F01, -52F00/01SR20DET S13/S14Pencil COPExternal power transistor3Falling
Nissan 22448-91F00 (U09123)SR20DET S15Pencil COPIntegrated3Falling
Nissan 22448-02U10/11 (U09122)RB20DET, RB26DETT (R32), RB25DET to 1995COPExternal six-channel3Falling
Nissan 22448-25U00 (U09105)RB25DET S2, RB26DETT R33/R34COPIntegrated3Falling
Nissan 22448-AA100/101 (U09108)RB25DET NEOCOPNot established
Nissan 22448-8J11x (U16N01), -AL61x (U08105)VQ35DEPencil COPIntegrated3Falling
Nissan 22448-JF00B (U18N02)VR38DETT (R35 GT-R)Pencil COPIntegrated3Falling
Mitsubishi early 4G63 coilsGalant VR-4, Evo I–III, EclipseWasted-spark two-postExternalIgniter
Mitsubishi MD321461, MD363552 (U12C03)4G63 Evo IV–IXPlug-top coil plus lead to partnerIntegrated3Falling (owner reports)
Mitsubishi 1832A016 (U18C02)4B11 Evo XPencil COPNot established3
Subaru 22433AA430 (U13F03)EJ20K (WRX MY99–00)Wasted-spark blockExternal two-channel3
Subaru 22433AA561, AA451/550/551, AA640/641EJ205, EJ207, EJ255, EJ257Pencil COPIntegrated3
Mazda B61P, BPE8-18-10XMX-5 NA (B6-ZE, BP)Wasted-spark two-post, two packsExternalIgniterGoing low (MegaSquirt)
Mazda BP4W-18-10XMX-5 NB1 (BP-4W)Wasted-spark two-post, two packsIntegrated4Falling
Mazda N3A1/N3A3-18-10013B-REW (RX-7 FD3S)Leading and trailing coilsExternal three-channelIgniterFalling
Mazda N3H1-18-100 (U15M01)13B-MSP (RX-8)COPIntegrated3Falling

Toyota

IGT and IGF

Toyota's ignition interface uses two signals. IGT is the ECU's 5 V trigger: high before the spark, falling at the ignition point. IGF is the igniter's confirmation, generated from the primary back-EMF; the ECU holds a shared IGF line at 5 V and each igniter pulls it low when its coil fires. If IGF is missing, the factory ECU sets a fault in the P1300 family and stops injection to protect the catalyst. Good IGT and IGF signals are 4.5 to 5.0 V square waves. On older external igniters a dwell-control circuit in the igniter decides when the primary current starts, so the IGT pulse width is not necessarily the coil's on-time (Motor magazine, quoting Toyota service text). Haltech leaves IGF unconnected on its JZ and 3S installations.

2JZ-GTE and 2JZ-GE, non-VVT-i (90919-02205)

The 1993–98 Supra (JZA80) uses six coil-on-plug units fired individually through an external igniter. Toyota's 1997 Supra repair manual gives the primary resistance as 0.54 to 0.84 Ω cold (−10 to 50 °C) and 0.68 to 0.98 Ω hot (50 to 100 °C); no secondary figure is published. Haltech specifies constant charge, falling edge, and warns that dwell above 2.2 ms at 14 V can make the ignition break up near 6000 rpm on the coil-on-plug JZ engines. Haltech shows the igniter pins only as an image.

1JZ and 2JZ VVT-i (90919-02216)

The VVT-i JZ engines have three coils, each mounted on one plug and feeding its partner cylinder through a lead, run as wasted spark. Hitachi lists 90919-02216 for the JZX100 1JZ-GE and 1JZ-GTE (from September 1996), the JZX110 1JZ-GTE, the JZA80 2JZ-GTE from September 1997, the JZS161 2JZ-GTE and the JZS155 and JZS157 2JZ-GE. Haltech states these coils need the external VVT-i igniter, contrary to the common assumption that they are smart. Igniter pins (Haltech): C1, C2 and C3 coil negatives for pairs 1/6, 2/5 and 3/4; +B 12 V; TAC tacho; GND to the head; T1, T2, T3 ECU ignition outputs 1 to 3; IGF, left unconnected. Haltech specifies constant charge and falling edge, warning that other settings will damage the ignition system. One parts retailer also lists this coil for the US 2JZ-GE Supra from 1993, which conflicts with the Toyota dealer catalogue's 90919-02205 for those cars; the retailer's entry is probably the 1998 US VVT-i car but this is not confirmed.

3S-GE and 3S-GTE

Haltech groups the 3S-GTE generations 1 to 3 (1986–1999) as distributor engines with one coil, 90919-02197 on the SW20 MR2, fed through an external igniter. Igniter pins: C coil negative, B coil positive, T IGT from the ECU, F IGF (left unconnected), EXT tacho. Generation 4 and 5 3S-GTE engines (for example the ST246W Caldina from 2002) use direct-fire coils with internal igniters, listed by Hitachi as 90919-02239.

Four-pin smart coil-on-plug (1ZZ, 2ZZ and related)

Toyota's later four-pin coils, including 90919-02239, -02240, -02243 and -02262, are smart pencil coils with current limiting. Hitachi lists -02239 for the 1ZZ-FE in the Celica (ZZT230/231), Corolla (ZZE12x) and MR-S (ZZW30), the 3S-GE in the Altezza (SXE10) and the generation 4/5 3S-GTE. Pinout, numbered as Haltech does for the 2ZZ-GE: 1 +B 12 V, 2 IGF, 3 IGT, 4 earth. Some owners number the same physical pins from the other end ("earth, trigger, feedback, power" looking into the plug), so the earth and supply pins should be confirmed by continuity to the body before connection. They trigger from 0–5 V logic on a falling edge, and aftermarket ECUs do not need IGF.

No ECU-maker dwell is published in text. An HP Academy tutor posted a scoped table for an unidentified 1ZZ coil, with a warning that these coils are damaged by over-dwelling:

Supply8 V10 V12 V13 V14 V15 V
Dwell, ms6.34.43.22.72.42.2

That table is an owner-grade figure; another MR2 owners' club table gave 2.0 ms at 14 V and noted that more than one 1ZZ coil exists.

Honda

K-series and F20C coil-on-plug

Hitachi maps 30520-PNA-007, -RRA-007, -PCX-007, -PNC-004 and -RWC-A01 to one replacement, U14H01. Applications include the F20C in the AP1 S2000 (1998–2005, -PCX-007), the K20A in the DC5, EP3, FD2 and FN2 Type R and the K24A in the Accord and CR-V. They are smart pencil coils on a three-pin connector: 1 ECU signal, 2 earth to head, 3 switched 12 V (Haltech). Haltech specifies direct fire, constant charge, falling edge, and warns that wrong settings will damage the coil and possibly the ECU. ECUs that ask for the dwell-start edge (an HP Academy tutor gives Autronic as an example) need the opposite setting.

K-series dwell is disputed. A table attributed to MoTeC and reposted on ECUMaster and Link forums gives 4.8 ms at 8 V, 3.0 at 10 V, 2.5 at 11 V, 2.1 at 12 V, 1.7 at 14 V and about 1.5 at 15 V; a Link forum reply suggests 1.8 to 2.0 ms at 14 V, and an ECUMaster reply calls the table too short. A Link forum thread reports coils failing at 4.0 ms. No first-hand MoTeC or Honda document has been found, so none of these is better than owner grade. An owner also reports that K20 and K24 coil pinouts differ, while Hitachi maps both to one replacement; the difference may be in the harness rather than the coil.

B, D and H-series distributors

On the B, D and H-series the coil and igniter are both inside the distributor. Haltech's B-series pinout uses distributor pin 1 as the ignition input (yellow/black) and pin 9 as switched 12 V, and specifies constant charge with a rising edge, unlike most coils. The H22A coil is 30510-PT2-006 (Hitachi U12H06), used in the BB1 and BB6 Prelude and CD6 and CL1 Accord. Honda's Civic specifications give 0.63 to 0.77 Ω primary and 12.8 to 19.2 kΩ secondary for the TEC distributor coil, and 0.45 to 0.55 Ω and 22.4 to 33.6 kΩ for the Hitachi-type coil (from a reproduction of the Honda data); which coil a particular B18C carries is not established. Reported failures are cracked igniter solder joints from heat cycling and worn distributor bearings.

Nissan

CoilIgniterCoil pinsNotes
SR20DET S13/S14 (22448-50F01; 22448-52F00/01)External four-channel power transistor− igniter output, + 12 V, E earthIgniter: i1–i4 ECU outputs, G earth, e1–e4 coil negatives. An owner reports the S13 power transistor does not work with S14/S15 coils
SR20DET S15 (22448-91F00)IntegratedIB ECU output, G earth, + 12 VS15 Silvia 1999–2002, four per engine
RB20DET, RB26DETT R32, RB25DET to 1995 (22448-02U10/11; coil body 22433-60U01/02)External six-channel on the coil cover− igniter signal, + 12 V, E earthHaltech: cannot be wired directly to the ECU. Igniter: 1–6 ECU inputs, 11–16 coil signals, 17 earth
RB25DET Series 2, RB26DETT R33/R34 (22448-25U00)IntegratedIB ECU output, G earth, + 12 VConstant charge, falling edge. A vendor names Hanshin as maker
RB25DET NEO (22448-AA100/101)Not establishedER34, ENR34 1998–2001; Haltech's R35 coil kit excludes NEO engines
VQ35DE (22448-8J11x; 22448-AL61x on CPV35)Integrated1 ECU output, 2 earth, 3 12 VVQ35HR (22448-JA10C) uses the same three-pin connection as the R35 coil
VR38DETT "R35" (22448-JF00B)Integrated1 ECU output, 2 earth, 3 switched 12 V (harness side)Hitachi pencil coil. See below

The R35 coil is widely reused on RB and JZ engines. Haltech's information sheet for its R35 coil kit requires falling edge and constant charge to be set before the coils are connected, and states that the coil must always have an earthed plug when firing. Haltech's dwell table is the only ECU-maker text figure found for a Japanese coil:

Supply, V910111213141516
Dwell, ms3.303.233.163.093.012.942.872.80

A conversion-kit maker gives 4.1 ms at 14 V; the Haltech figure is preferred as ECU-maker documentation. The same kit maker advises resistor plugs and sequential (not wasted-spark) firing.

Mitsubishi

  • Early 4G63 (Galant VR-4, Evo I–III, first-generation Eclipse): dual-post wasted-spark coils driven by an external igniter. Igniter pins (Haltech): OC1 and OC2 coil negatives, IB1 and IB2 ECU outputs, VB 12 V, TAC tacho, GND.
  • 4G63 Evo IV–IX (MD321461 for Evo IV–VI, MD363552 for Evo VII–IX; Hitachi U12C03): two plug-top coils, each also feeding its opposite cylinder through a lead, with internal igniters. Pins: 1 switched 12 V, 2 earth, 3 ECU signal. The Evo 6.5 swaps the ECU's ignition outputs for pairs 1+4 and 2+3 (Haltech). Owners report falling-edge triggering. That Mitsubishi Electric (Diamond) made the original coils is not established.
  • 4B11 Evo X (1832A016; Hitachi U18C02): three-pin pencil coils. A vendor cross-reference to H6T 11471 suggests Mitsubishi Electric manufacture. Pinout, igniter location and dwell are not established.

Subaru

  • EJ20G (WRX MY93–97): coil-on-plug with an external four-channel igniter (Haltech).
  • EJ20K (WRX MY99–00, 22433AA430): one block holding two dual-post wasted-spark coils, with an external two-channel igniter. Coil pins: 1 to igniter pin 5 (cylinders 1+2), 2 12 V, 3 to igniter pin 6 (cylinders 3+4). Igniter pins: 1 and 2 ECU outputs, 3 earth, 4 not connected, 5 and 6 coil negatives.
  • EJ205, EJ207 and later turbo EJ: smart pencil coils wired directly to the ECU. Pins: 1 (nearest the latch) ECU signal, 2 earth, 3 12 V. Hitachi lists 22433AA561 for GD/GG turbo 2000–02, 22433AA451, AA550 and AA551 for 2002–07, and 22433AA640 and AA641 for the GRB, GVB, GRF and VAB turbo.
  • Later naturally aspirated EJ20 (22433AA500/AA580, GH6/GH7 2007–11): single wasted-spark block; igniter location not established.

Haltech's EJ20 page describes the EJ207 as wasted spark in one section and coil-on-plug in another; the Hitachi listings for GD-chassis coils support coil-on-plug for that period.

Mazda

  • MX-5 NA (B6-ZE and BP 1.8): two dual-post wasted-spark packs with an external igniter. Igniter pins (Haltech): OC1, OC2 coil negatives; IB1, IB2 ECU outputs; VB; TAC; IGf; GND. MegaSquirt drives the stock igniter with the spark output set to "going low". Vendor part numbers include B61P-18-10X (1.6) and BPE8-18-10XA (1.8).
  • MX-5 NB1 (BP-4W, 1999–2000): two dual-post packs with internal igniters on a four-pin connector: A 12 V, B not used, C earth, D ECU signal. Haltech: wasted spark, constant charge, falling edge. Vendor part numbers BP4W-18-10X; BP6D-18-100A is listed by vendors for either 1999–2000 or 2000–05.
  • RX-7 FD3S 13B-REW: a dual-post leading coil and two trailing coils, driven by a three-channel igniter. Igniter pins (Haltech): 1 not connected, 2 leading coil negative, 3 leading ECU signal, 4 trailing 2 coil negative, 5 12 V (black/white), 6 trailing 2 signal, 7 trailing 1 coil negative, 8 trailing 1 signal. Wasted spark, constant charge, falling edge. Coil numbers N3A3-18-100 (leading) and N3A1-18-100 (trailing) and trailing igniter N3A1-18-251 are given by parts sellers, who swap N3A1, N3A2 and N3A3 between roles. On the FC3S the trailing igniter uses a toggle signal: Haltech runs it in distributor mode at 5.0 ms and states its Elite ECUs cannot drive it.
  • RX-8 13B-MSP (N3H1-18-100 with suffixes; Hitachi U15M01): four smart coils, described in Mazda's service manual as an "ignition coil with built-in power switch" with terminals A, B and C, checked for continuity only. Pins (Haltech): A signal, B earth to rotor housing, C 12 V; direct fire, constant charge, falling edge. Coil failure and misfire are among the most widely reported RX-8 problems.

An AMP EFI bench comparison at 13.5 V found a Mazda MZR coil saturating at 4.0 ms with 97 mJ, and a Mazda "Miata pencil" coil at 2.0 ms with 38 mJ (part numbers not given).

Korean and motorcycle coils

The Hyundai Theta 2.0T (Genesis Coupe) coil 27300-2G000, superseded by 27300-3F100, is listed by a dealer with a two-pin connector. Its igniter arrangement and dwell are not established.

Yamaha R6 stick coils are popular on small conversions. An EVO Fuel Injection document for Performance Electronics PE3 ECUs gives charge times; a Link forum post calls them dumb coils needing an external igniter.

Coil16 V14 V12 V10 V8 V
Yamaha R6 2008 on (13S/BN6), ms1.201.501.902.403.00
Yamaha R6 2006–07 (6T558/5Z26), ms1.602.002.905.007.00

The same document gives 1.95 ms at 14 V for the Honda CBR600RR coil 129700-4510.

Not established

  • ECU-maker text dwell figures for SR20, RB, VQ, 4G63, EJ, 13B and MX-5 NB coils (Haltech publishes them as images).
  • Secondary resistance for any Toyota coil-on-plug.
  • The original makers (Denso, Hitachi, Mitsubishi Electric, Hanshin) of most coils, which replacement catalogues do not show.
  • Igniter location on the RB25DET NEO, 4B11 and later naturally aspirated EJ coils, and a manufacturer specification for Hyundai and Kia coils.

Sources

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.