Tuning Wiki
Browse Ford

These examples concern two different turbocharged Ford EcoBoost ST models: the 2015 Focus ST 2.0 and 2016 Fiesta ST 1.6. Their engines, gearboxes, controllers and calibration strategies are not interchangeable. Check the actual market, vehicle, controller, operating system, installed parts and available VCM Suite parameters before applying a procedure.

Engine, gearbox and support identification

Ford's North American 2015 Focus ST supplement identifies a 2.0-litre EcoBoost and the Getrag-Ford MMT6 six-speed manual. The 2016 North American Fiesta ST supplement identifies a 1.6-litre gasoline turbocharged direct-injection four-cylinder and Ford B6 six-speed manual; it also describes an original factory overboost feature. These are specifications for those particular markets and years, not a specification for all Focus or Fiesta STs. Ford: 2015 Focus ST supplement; Ford: 2016 Fiesta ST supplement.

HP Tuners lists 2013–18 Focus ST 2.0 EcoBoost, 2013–17 Fiesta ST 1.6 and a separate 2013–18 non-US Fiesta ST 1.6 MED17.0.1 application. Check the vehicle, market, device-generation legend and exact ECU against HP Tuners' current Ford support list; do not assume every ST has that Fiesta ECU or that all parameters are exposed in every calibration. These examples have manual gearboxes and do not establish support for an automatic transmission controller.

2015 Focus ST: camshaft and speed-density modelling

Calibrating a Focus ST with aftermarket camshafts, turbo and intercooler is not fully documented. In a High Performance Academy discussion by a 2015 Focus ST owner, a tutor noted that changed cams affect volumetric efficiency at different cam positions, and the owner reported using the speed-density calculator and seeing multiple mapped points. The thread provides no validated cam numbers, no complete tuning procedure and no proven way to lock a particular mapped point; its attached screenshots were not publicly accessible.

For background, an HP Tuners Ford strategy explanation describes mapped points associated with pairs of intake and exhaust cam positions and a Speed Density Calculator that presents model data as a VE surface on supported files. Its Mustang illustration and point counts do not establish the number or exact table definitions in this Focus calibration. Confirm what is actually present in the file; camshaft hardware changes can affect airflow and torque over more than one operating point. Obtain cam and injector data for the exact hardware, and check mechanical cam timing and clearance before calibration.

Where the vehicle provides them, log engine speed, MAP, intake and exhaust cam position, commanded and measured lambda, fuel pressure, knock-related channels and mapped-point weights. Select only the available channels and check units, operating conditions and data rate. Review VCM Scanner histograms against the actual table axes and operating state, rather than applying a single average correction to every mapped point. Validate changes with a fresh log and appropriate independent mixture measurement. HP Tuners: scanning configuration.

The airflow-vs-period table used in a truck example could not be found in a Focus ST HP Tuners file, and a separate Focus ST discussion did not establish why. The transferable lesson is to identify the strategy and available definitions in the vehicle's own file; the thread does not establish that all Focus STs lack a MAF table, or that short-term fuel trim alone is an appropriate high-load correction.

2016 Fiesta ST: boost deviation during third gear

One owner report describes a boost deviation on a modified Fiesta ST. A 2026 Fiesta ST180 discussion concerns a 2016 car tuned with HP Tuners, with an MRX hybrid turbo, larger injectors and intercooler. Boost in third gear at high rpm reportedly exceeded the stated target and triggered a cut, and changes to requested torque and wastegate duty tables had not resolved it. Actuator authority and control-response explanations were proposed. These are unverified observations and hypotheses for one modified car: the post does not prove the cause or a successful repair, and its pressures are not recommended targets.

For a similar complaint, first check trouble codes and the physical boost-control system, including the actuator, linkage, hoses, solenoid and sensor calibration, against the correct hardware and Ford service information. In VCM Scanner compare requested and measured pressure, barometric pressure, engine speed, throttle, gear and available wastegate control and intervention channels on the same timeline. Verify whether each pressure is absolute or gauge and where it is measured. Compare like-for-like conditions and stop a loaded test if pressure exceeds the safe calibrated limit or an intervention occurs. A recorded duty command alone does not demonstrate actual wastegate position; investigate the mechanical system as well as the calibration. Do not defeat protection or copy another car's PID, preload or duty-cycle values.

Preparation and related pages

Record faults before reading: HP Tuners cautions that a vehicle read clears diagnostic trouble codes. Save the vehicle's original supported calibration, record the modifications and fuel, and check the logging channel list before changing a file. HP Tuners: getting started with VCM Editor.

See also Ford Fiesta: generations and engines, VCM Scanner and HP Tuners MPVI4.

Continue the conversation

If this topic interests you, consider joining the following forums. They host material referenced in this article.