Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Dynamometers
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

A dyno graph plots a vehicle or engine's output against engine speed, road speed or time. It can show where power and torque rise, peak and fall, and help compare a change made under repeatable conditions. The lines are produced from sensor readings and calculations: what the dyno measures directly, and what it estimates, depends on the machine and the test.

Illustrative torque and power curves against engine speed, with separate vertical scales and an example at 5000 rpm
Illustrative data, not a vehicle test: 350 N·m at 5,000 rpm corresponds to about 183 kW. Each curve uses its own labelled vertical scale. Original graph created for Tuning Wiki, CC BY 4.0.

How to read the graph

  1. Start with the axes. The horizontal axis is often engine speed in rpm, but it may instead show roller speed, road speed or time. Vertical axes can use different scales: one may be power in kW, hp or PS, while the other is torque in N·m or lb·ft. Check the label and units for each line.
  2. Identify the output. Is the result engine-dyno shaft power, chassis-dyno wheel power, hub power or estimated crankshaft power? Is it corrected to a standard atmosphere or uncorrected? They are different labels for different things.
  3. Read values at the same speed. Follow a chosen rpm up to each curve, then across to its own vertical scale. Note peak values and where they occur, but inspect the whole useful operating range. A wider useful curve and a higher peak answer different questions.
  4. Check the test information. Look for the machine and test type, gear, engine-rpm source, date, atmospheric conditions, correction standard, smoothing and run identifier. Some graphs omit information needed to compare them fairly.

Multiple runs can be overlaid for a before-and-after comparison. Check that both traces use the same axes, units, correction, smoothing and rpm range before deciding a difference is real. Graph zoom and independent scales can make a change appear larger or smaller. Dynojet's graph documentation describes selectable axes, conditions and the area under a curve.

Torque, power and horsepower

Torque is a turning moment. Power is the rate of doing work: at any instant it is torque multiplied by angular speed. For torque and speed at the same shaft, the relationships are:

  • Power (kW) = torque (N·m) × speed (rpm) ÷ 9,549.3.
  • Power (mechanical hp) = torque (lb·ft) × speed (rpm) ÷ 5,252, approximately.
  • 1 kW ≈ 1.341 mechanical hp; 1 kW ≈ 1.360 metric horsepower (PS). A printed “hp” label should be checked for its intended unit.

Worked example: at 4,000 rpm, 400 N·m gives 400 × 4,000 ÷ 9,549.3 = 167.6 kW, approximately 224.7 mechanical hp or 227.8 PS. These are different units describing the same power. The calculation is valid only when the torque and rpm refer to the same shaft and instant. US engine-test procedures describe determining power from synchronised speed and brake torque: 40 CFR 1065.15.

Power can continue to rise after peak torque because rpm is still increasing. At 5,252 rpm, the numerical values of mechanical hp and lb·ft are equal if they describe the same shaft and use the same basis. That does not guarantee the lines visibly cross there: the power and torque axes may have different scales. The 5,252 rule does not apply directly to kW and N·m or to PS.

What does a dyno actually measure?

SystemTypical direct signalsWhat the graph derives or reports
Brake/load-cell dynoBrake reaction force through a known arm, or shaft-transducer torque, plus rotational speed. Additional channels depend on installed sensors.Torque and power at the applicable measurement boundary. A transient sweep can require compensation for accelerating inertia; measured brake reaction alone is not necessarily total input torque.
Inertia-only rollerRoller speed and its change over time; engine rpm and atmospheric channels may also be recorded.Software uses known effective roller inertia and acceleration to infer net torque and power, with the dyno's treatment of losses and other rotating components. It does not need a brake load cell for an inertia sweep.
Hub dynamometerHub unit speed and its force, torque or hydraulic signals, according to design.Hub output and, if software offers it, a separate estimate of engine output. The gearbox and final drive are still between engine and hubs.
Engine test cellEngine/absorber shaft speed and torque or brake reaction, plus installed test-cell channels.Engine-shaft brake power under the stated test conditions. Accessories, exhaust, correction and engine configuration affect comparison with a published vehicle rating.
On-road calculatorVehicle speed/acceleration and sometimes GPS, slope or other logged signals.An estimate using vehicle mass, road gradient, drag and other assumptions; it is not necessarily a physical dyno brake measurement.

During a sweep, some torque accelerates the engine and test equipment. A simple inertia term is torque = moment of inertia × angular acceleration, referred to the same shaft. Some systems compensate; others report a different quantity or convention. Test method and compensation can therefore change the graph. SuperFlow: acceleration effects; engine and dynamometer inertia.

Wheel, hub and crankshaft power

Wheel power on a rolling road is the output measured or inferred at the tyre-and-roller interface, according to the dyno's method. It includes the effect of transmitting power through the gearbox and final drive and the tyre/roller contact. Hub power removes that tyre/roller interface but retains the drivetrain between the engine and hub. Engine or crankshaft power from an engine dyno is measured at the engine's test shaft under its specified setup.

Some chassis dynos also display estimated crank or flywheel power. Depending on the system, the software may use a coastdown, a model or an assumed loss to estimate what was lost between engine and rollers. This can be a useful estimate, but it is not a direct crankshaft torque measurement. Losses measured during deceleration do not necessarily equal losses under power, and there is no fixed percentage that accurately describes every vehicle, gear, speed and temperature. Ask how the figure was produced. MAHA's MSR 500/1 lists wheel power, drag power and calculated engine power as distinct outputs.

A graph may show torque against engine rpm even though the physical sensor is at the roller or hub. Software can derive an engine-speed-referenced torque from power and engine rpm; that is not necessarily directly measured crankshaft torque. Actual wheel torque is different because gearing changes torque and speed. Confirm what each torque axis represents.

Why can the same vehicle produce different results?

CauseEffect to investigate
Measurement boundary and softwareWheel, hub, direct engine-shaft and estimated crank output are different. Dynos can use different loss models, inertia compensation, calculation and correction settings. Compare like with like.
Calibration and conditionLoad cells, speed pickups, roller inertia and environmental sensors need correct setup and verification. Mechanical faults, tyre slip or a bad rpm signal can distort results. Repeatability is not the same as traceable accuracy.
Test mode and rampAn inertia pull, controlled ramp and steady-state test can exercise the engine differently. Acceleration rate, turbo response, load control and rotating inertia affect the result; faster does not imply a universally higher or lower reported figure on every system.
Gear and transmissionGear ratio changes roller acceleration and test duration; automatic shift, converter slip, driveline temperature and electronic torque management can affect a run. Use a suitable, consistent gear and vehicle-specific procedure.
Tyres and setupOn rollers, tyre construction, pressure, temperature, alignment, restraint and slip influence the contact and losses. A hub dyno has no driven-tyre-to-roller contact, but has its own adapters and measurement path.
Air and temperaturesAmbient pressure, temperature and humidity affect combustion; coolant, oil, inlet and charge-air temperatures, cooling airflow and heat soak also matter. A correction factor cannot restore an overheated intercooler or undo ECU intervention.
Fuel, state and settingsFuel, boost, ignition, vehicle condition, test mode, aids and ECU adaptation can change output. For hybrid or electric vehicles, record battery state of charge, temperature and applicable power limits.
PresentationDifferent hp units, correction standards, smoothing, graph scaling or a result shown at the wheels versus estimated at the crank can make two charts appear to disagree. Smoothing changes the displayed trace and can hide or alter narrow peaks.

SuperFlow's testing guidance discusses repeatable test setup and the limitations of atmospheric corrections. A correction adjusts output to a stated reference atmosphere; it is not a guarantee that every engine, environment or test method becomes directly comparable. Dynojet documents selectable SAE, DIN and other corrections. Record the exact standard and factor, and compare uncorrected data as well when available.

What a graph cannot tell you on its own

  • A power curve alone does not show air–fuel ratio, exhaust temperature, knock, boost or fuel pressure. These need suitable sensors and logs, and even then must be interpreted in context.
  • It does not prove a tune is safe, road-legal, durable or optimal in every gear and condition. A short power pull does not reproduce every road, transient or sustained-load situation.
  • A peak number does not tell you the entire acceleration result. Vehicle mass, gearing, traction, aerodynamic drag, shift strategy and the power available through the relevant rpm range all matter.
  • A smooth curve does not prove the engine is healthy or the measurement accurate; smoothing can conceal spikes. A single unusual run needs investigation rather than an immediate conclusion.

Making a useful before-and-after comparison

  1. Record the vehicle specification, fuel, dyno, measurement boundary, calibration and test mode. Keep tyre and restraint setup, gear, rpm source, cooling and safety procedure consistent.
  2. Warm the vehicle consistently and record ambient conditions, intake, coolant and oil temperatures where available. Avoid comparing a cold baseline with a heat-soaked later run.
  3. Make repeat baseline runs where safe, then make the change and repeat under the same conditions. Note intervention, wheel slip, shift or aborted runs instead of averaging them blindly.
  4. Overlay traces in the same units and correction, with the same smoothing and rpm range. Compare values at several matching speeds and report the range of repeat runs as well as the peak.
  5. For a small improvement near the normal run-to-run variation, repeat or revert to the original setup if practical before attributing the difference to the change.

See dynamometer measurement and interpreting results, calibration and verification and test setup and safety.

Agreeing a dyno session

Before booking, explain the vehicle’s hardware, fuel, existing faults and the result sought. Agree whether the session is a measurement only, diagnosis or calibration, which operating conditions and sensors are included, and what happens if a mechanical problem or unsafe reading stops the test. A provider should identify the equipment and its suitability for the vehicle and driveline.

Ask for the test boundary and units, correction standard, baseline and final curves, relevant logs, fuel and setup notes, and a record of any changes or unresolved faults. These details make a later comparison more useful; a peak number alone cannot document the whole job. SuperFlow’s test guidance discusses consistent conditions and equipment calibration. Ask the provider how original and final calibration files are retained and what recovery is supported for the particular ECU.