Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engines
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Caterpillar, Ford, Navistar

HEUI is a unit injector operated by engine oil, not a common rail of fuel. Caterpillar developed it. Ford, Navistar and others used it. Fuel is supplied to the injector at feed pressure through passages in the cylinder head. High-pressure oil, from a separate pump, acts on an intensifier piston inside the injector and that piston pressurises the fuel. There is no fuel rail at injection pressure. A test, a pressure figure or a return-quantity procedure written for a common rail does not apply.

For testing equipment and its distinction from common rail, see mechanical and unit diesel injector testing.

How the 6.0 litre injector is driven

The oil rail is the high-pressure side. A high-pressure oil pump feeds it. An injector pressure regulator, a pulse-width valve that is normally open, bleeds oil until the controller commands it towards closed. With the regulator unplugged, the rail cannot build pressure and the injectors will not fire.

Inside the injector a spool valve sits between two coils. Each coil is driven at 48 V and about 20 A by the fuel-injection control module. One coil opens the oil path. The other closes it and lets the oil drain back to the crankcase. The spool only moves about 0.017 inch. The open coil is energised for about 800 millionths of a second. Oil then pushes the intensifier piston down. The piston area is about seven times the plunger area, so fuel pressure at the nozzle is about seven times the oil pressure.

Engine conditionHigh-pressure oilFuel at the nozzle, about seven times the oil
IdleAbout 600 psiAbout 4,200 psi
Wide-open throttleUp to about 3,000 psiUp to about 21,000 psi

Fuel enters the side of the injector from the head passages, at the pressure of the fuel pump, and is only raised to injection pressure inside that injector. A fuel pump that is weak still matters, because the injector has nothing to intensify, but a normal fuel-pump pressure does not mean the injector can fire. The oil does that.

Stiction, oil and air

Stiction is the spool sticking in its bore, so the oil arrives late or not at all. The usual causes are the oil and the service interval. These engines are particular about viscosity. Oil that holds air makes foam, and foam in the injector is a pressure that is not really there, so the engine misfires. All oil foams when the pump beats it. The anti-foam package is what lets the foam collapse. Oil other than the one the engine was specified with, or oil left in too long, leaves scum that sticks the spool. The coils themselves also fail and leave a dead injector. Contribution codes on several cylinders are not a reason to replace every injector until the oil rail on that bank has been proved.

A bank that is dead, with a healthy spool time

On a 6.0 litre the scan tool can show contribution. Cylinders 1, 3, 5 and 7 are one bank. A miss on that whole bank, with plausible engine data and those four contribution codes, is not automatically four injectors. A spool-time measurement that is normal, and a cylinder-kill test that shows those four cylinders contributing nothing, moves the fault off the spool and onto the oil that was supposed to reach them.

High-pressure oil at idle should be about 600 psi and should rise as the engine is accelerated. If that pressure is present and one bank is still dead, the branch from the high-pressure oil pump to that bank is leaking. The leak may not be visible with the cover off and the engine cranking. The branch has to be inspected. Replacing the injectors on the dead bank, because the codes named the injectors, leaves the oil leak in place. The new injectors then fail to fire for the same reason.

No-start

The same two requirements apply as on any diesel: enough cranking speed to make heat, and fuel injected at the right time. About 150 rpm is the minimum cranking speed worth testing beyond. The 6.0 litre no-start measurement is injector control pressure, read as voltage. During a long crank the controller can substitute a pressure number. The sensor voltage does not get substituted.

Injectors are not pulsed until that voltage reaches about 0.8 V. A cranking voltage that sticks near 0.67 V, with a slow crank in very cold oil, is an oil rail that is not building. Combined with a circuit code for the injector pressure regulator, the regulator is the part that cannot close. On the 6.0 litre the regulator sits under the turbocharger, the degas bottle and the fuel-injection control module. The connector can be off its pins without being visible until the heat shield is looked under. A borescope is enough to see a plug that is not seated. The 7.3 litre regulator is easier to see. Do not strip the 6.0 litre to look until the voltage and the code have said the regulator circuit is the fault.

One stored code in that position is P2623, an injector-pressure-regulator circuit fault. An unplugged regulator and an open coil both set a circuit code, and both leave the normally open regulator unable to build oil pressure.

After the plug is seated, confirm at temperature. Select engine speed, injector control pressure, regulator duty and coolant temperature. The useful check is a hot idle. On a system with no high-pressure oil leak the regulator duty sits at about 23 percent at hot idle, and a restart is immediate with the duty still at that figure. A duty that has to rise far above that to hold idle pressure is the leak the injector codes were describing.

Fuel delivery into the chamber, if the oil pressure is good and the engine still will not fire, is checked by watching the exhaust while cranking. Atomised fuel should appear. A particulate filter can hide it. Pulling a glow plug and cranking shows the cloud from that cylinder. This is a last resort, and it is not an invitation to spray starting fluid into the intake.

What to log

For a HEUI no-start or miss, the useful set is the three fuel-injection-control-module voltages, engine rpm, injector-control-pressure voltage, and regulator duty. Spool time, where the tool can read it, separates a sticking spool from an oil leak. A kill test separates a cylinder that contributes from one that does not. High-pressure oil pressure at idle and as the engine is opened separates a weak oil pump from a leak. Fuel-pump pressure is the remaining check, because the intensifier cannot inject fuel that never arrived at the injector.

A common-rail injector return test or diesel rail-pressure test does not test this engine's high-pressure oil actuation system. Use the procedure for the exact engine. The pressure that makes the injection is oil.