Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

Petrol engines have used several ways to meter fuel and mix it with incoming air. Identifying the layout is the first step in choosing a diagnostic or tuning method: a carburettor, a mechanical injection system and an electronically controlled injector do not respond to the same adjustments.

Where the fuel enters

LayoutFuel deliveryWhat controls metering CarburettorFuel enters the airflow upstream of the inlet ports.Pressure differences and calibrated fuel circuits respond to airflow; individual designs use different enrichment and idle devices. Mechanical injectionDepends on the design; some systems deliver fuel continuously near the inlet valves.Mechanical metering responds to engine operating conditions. Some versions add electronic correction. Throttle-body injectionOne or more electronically operated injectors supply fuel centrally, upstream of the inlet runners.The controller commands injection using its sensors and calibration; the manifold distributes the mixture. Port injectionInjectors deliver fuel into the inlet ports, upstream of the inlet valves.An ECU controls injector operation using its programmed strategy and sensor inputs. Direct injectionInjectors deliver fuel into the combustion chamber.An ECU controls injection and high-pressure fuel delivery; injection timing and pressure are system-dependent. Combined port and directThe engine has both port and direct injectors.The ECU selects or combines delivery according to its particular strategy and operating conditions.

Bosch describes port injection as forming the mixture in the intake manifold before the inlet valve, and documents combined port/direct systems as a separate arrangement. Direct injection uses a high-pressure pump and rail; the actual hardware and pressure ranges are application-specific. Bosch: petrol port injection and combined systems; Bosch: direct-injection fuel rail.

What changes when tuning

A carburettor has physical circuits and components such as jets, needles and accelerator pumps. On electronic injection, injector flow, fuel pressure, measured or modelled air charge and ECU calibration all affect delivery. Mechanical injection has its own system-specific adjustments. None guarantees correct distribution, mixture or performance simply because of its type; engine condition, parts, calibration and validation matter.

Electronic control permits the ECU to adjust operation in response to sensors and may use exhaust feedback, but operating modes and sensor coverage differ. A throttle-body injector feeds a shared manifold, whereas port injectors meter fuel at individual ports. Even with port injectors, differences in airflow and component condition can still produce cylinder-to-cylinder variation.

Before modifying a system

Identify the actual fuel system and ECU, including any previous conversion. Verify wiring and part numbers against the applicable documentation.Establish a sound baseline: check for fuel and air leaks, ignition and mechanical faults, and measure fuel pressure using the correct procedure for the system.Plan fuel delivery, control hardware, sensors and calibration together. For a conversion, also check packaging, fuel compatibility, return arrangements and vehicle-system integration.Validate mixture and operating behaviour with suitable instruments and controlled testing. Direct-injection systems can retain hazardous fuel pressure: follow the manufacturer's depressurisation and service instructions.

Further reading

Carburettor tuning, jetting and setup Bosch K-Jetronic and Bosch D-Jetronic Petrol direct injection and combustion modesPetrol port injector calibration Standalone ECU fuel tuning guide Mixture tuning: AFR and lambdaCarburettor tuning, jetting and setup Bosch K-Jetronic and Bosch D-Jetronic Petrol port injector calibration Standalone ECU fuel tuning guide Mixture tuning: AFR and lambda

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Petrol fuel delivery: carburettors and injection layouts

Petrol engines have used several ways to meter fuel and mix it with incoming air. Identifying the layout is the first step in choosing a diagnostic or tuning method: a carburettor, a mechanical injection system and an electronically controlled injector do not respond to the same adjustments.

Where the fuel enters

LayoutFuel deliveryWhat controls metering
CarburettorFuel enters the airflow upstream of the inlet ports.Pressure differences and calibrated fuel circuits respond to airflow; individual designs use different enrichment and idle devices.
Mechanical injectionDepends on the design; some systems deliver fuel continuously near the inlet valves.Mechanical metering responds to engine operating conditions. Some versions add electronic correction.
Throttle-body injectionOne or more electronically operated injectors supply fuel centrally, upstream of the inlet runners.The controller commands injection using its sensors and calibration; the manifold distributes the mixture.
Port injectionInjectors deliver fuel into the inlet ports, upstream of the inlet valves.An ECU controls injector operation using its programmed strategy and sensor inputs.
Direct injectionInjectors deliver fuel into the combustion chamber.An ECU controls injection and high-pressure fuel delivery; injection timing and pressure are system-dependent.
Combined port and directThe engine has both port and direct injectors.The ECU selects or combines delivery according to its particular strategy and operating conditions.

Bosch describes port injection as forming the mixture in the intake manifold before the inlet valve, and documents combined port/direct systems as a separate arrangement. Direct injection uses a high-pressure pump and rail; the actual hardware and pressure ranges are application-specific. Bosch: petrol port injection and combined systems; Bosch: direct-injection fuel rail.

What changes when tuning

A carburettor has physical circuits and components such as jets, needles and accelerator pumps. On electronic injection, injector flow, fuel pressure, measured or modelled air charge and ECU calibration all affect delivery. Mechanical injection has its own system-specific adjustments. None guarantees correct distribution, mixture or performance simply because of its type; engine condition, parts, calibration and validation matter.

Electronic control permits the ECU to adjust operation in response to sensors and may use exhaust feedback, but operating modes and sensor coverage differ. A throttle-body injector feeds a shared manifold, whereas port injectors meter fuel at individual ports. Even with port injectors, differences in airflow and component condition can still produce cylinder-to-cylinder variation.

Before modifying a system

  1. Identify the actual fuel system and ECU, including any previous conversion. Verify wiring and part numbers against the applicable documentation.
  2. Establish a sound baseline: check for fuel and air leaks, ignition and mechanical faults, and measure fuel pressure using the correct procedure for the system.
  3. Plan fuel delivery, control hardware, sensors and calibration together. For a conversion, also check packaging, fuel compatibility, return arrangements and vehicle-system integration.
  4. Validate mixture and operating behaviour with suitable instruments and controlled testing. Direct-injection systems can retain hazardous fuel pressure: follow the manufacturer's depressurisation and service instructions.

Further reading

Revision 2: Petrol fuel delivery: carburettors and injection layouts

Petrol engines have used several ways to meter fuel and mix it with incoming air. Identifying the layout is the first step in choosing a diagnostic or tuning method: a carburettor, a mechanical injection system and an electronically controlled injector do not respond to the same adjustments.

Where the fuel enters

LayoutFuel deliveryWhat controls metering
CarburettorFuel enters the airflow upstream of the inlet ports.Pressure differences and calibrated fuel circuits respond to airflow; individual designs use different enrichment and idle devices.
Mechanical injectionDepends on the design; some systems deliver fuel continuously near the inlet valves.Mechanical metering responds to engine operating conditions. Some versions add electronic correction.
Throttle-body injectionOne or more electronically operated injectors supply fuel centrally, upstream of the inlet runners.The controller commands injection using its sensors and calibration; the manifold distributes the mixture.
Port injectionInjectors deliver fuel into the inlet ports, upstream of the inlet valves.An ECU controls injector operation using its programmed strategy and sensor inputs.
Direct injectionInjectors deliver fuel into the combustion chamber.An ECU controls injection and high-pressure fuel delivery; injection timing and pressure are system-dependent.
Combined port and directThe engine has both port and direct injectors.The ECU selects or combines delivery according to its particular strategy and operating conditions.

Bosch describes port injection as forming the mixture in the intake manifold before the inlet valve, and documents combined port/direct systems as a separate arrangement. Direct injection uses a high-pressure pump and rail; the actual hardware and pressure ranges are application-specific. Bosch: petrol port injection and combined systems; Bosch: direct-injection fuel rail.

What changes when tuning

A carburettor has physical circuits and components such as jets, needles and accelerator pumps. On electronic injection, injector flow, fuel pressure, measured or modelled air charge and ECU calibration all affect delivery. Mechanical injection has its own system-specific adjustments. None guarantees correct distribution, mixture or performance simply because of its type; engine condition, parts, calibration and validation matter.

Electronic control permits the ECU to adjust operation in response to sensors and may use exhaust feedback, but operating modes and sensor coverage differ. A throttle-body injector feeds a shared manifold, whereas port injectors meter fuel at individual ports. Even with port injectors, differences in airflow and component condition can still produce cylinder-to-cylinder variation.

Before modifying a system

  1. Identify the actual fuel system and ECU, including any previous conversion. Verify wiring and part numbers against the applicable documentation.
  2. Establish a sound baseline: check for fuel and air leaks, ignition and mechanical faults, and measure fuel pressure using the correct procedure for the system.
  3. Plan fuel delivery, control hardware, sensors and calibration together. For a conversion, also check packaging, fuel compatibility, return arrangements and vehicle-system integration.
  4. Validate mixture and operating behaviour with suitable instruments and controlled testing. Direct-injection systems can retain hazardous fuel pressure: follow the manufacturer's depressurisation and service instructions.

Further reading