Gasoline direct injection (GDI, also called petrol direct injection) delivers fuel into the cylinder rather than into the inlet port. The ECU coordinates injection, air supply and ignition, while a high-pressure system supplies the direct injectors. Designs and operating modes differ considerably; direct injection alone does not tell you which combustion modes a particular engine supports. Bosch: gasoline direct injection

Fuel supply and injection
A low-pressure supply feeds a high-pressure pump, which supplies a rail and the direct injectors. The ECU monitors and regulates pressure using components specific to the system. Injector spray pattern, timing, number of events and pressure are calibrated together with combustion-chamber geometry and air motion. The pressure range shown in a supplier's description is not a diagnostic acceptance limit for another vehicle.
Some engines also have port injectors. Their controller can use either system or combine them, but the available modes and transitions must be established for the exact engine and software. The Audi EA837 evo example illustrates one such implementation.
Toyota's Japanese-market launch information identifies the naturally aspirated Lexus IS F 2UR-GSE V8 as a D-4S engine with both direct and port injection. Lexus describes the 2010 US-market IS F's port injectors as contributing at light and medium loads. This establishes the two fuel paths for those applications; it does not establish that every GDI combustion mode operates on them. The later RC F also uses a 2UR-GSE designation, but Lexus describes substantial changes including its intake, cylinder heads and dual-injection system. Identify model, market, year and ECU before transferring parts or calibration assumptions. Lexus: 2010 IS F; Lexus: RC F engine. Toyota: IS F launch and engine specifications.
Planning a conversion or engine swap
A conversion from port injection to direct injection is a whole-engine and control-system project. It needs a cylinder head and combustion chamber designed for the injector's position, seal and spray, a compatible high-pressure pump and drive, rail, lines, pressure measurement and regulation, as well as suitable injector drivers and calibration. A port-injection ECU or low-pressure fuel system cannot be assumed to provide these functions. Bosch's GDI system overview shows the pump, rail, injectors and coordinated engine-control functions.
For an engine already equipped with direct injection, a complete donor engine and matched control hardware can avoid inventing the combustion hardware, but still requires vehicle integration and validation. Check compatibility of the engine, pump, injectors, ECU, wiring, immobiliser, transmission and emissions equipment for the actual combination. If adding port injection to an existing GDI engine, retain or replace the direct-injection control and its safety functions with a documented compatible strategy; do not assume an auxiliary port system can operate the original high-pressure system by itself. See planning an EFI engine swap.
Injector sealing and high-pressure components require the correct service tools and application-specific procedures. Bosch describes dedicated sealing-ring service for its high-pressure injectors; this does not establish interchangeability with a different engine. Assess applicable registration and emissions requirements before planning a road-vehicle conversion.
Homogeneous and stratified mixtures
In a broadly homogeneous charge, fuel and air have time to mix across much of the cylinder before ignition. In a stratified charge, the mixture is deliberately less uniform: a region suitable for ignition is established near the spark plug while the overall cylinder mixture may be leaner. Injection timing, spray and in-cylinder motion all affect that preparation. The US Department of Energy describes both premixed and stratified approaches to dilute gasoline combustion. US DOE: advanced combustion strategies
Do not assume that every GDI engine runs a lean stratified mode. A particular engine may primarily use homogeneous, near-stoichiometric operation, and its usable modes depend on the calibration, hardware and emissions system. An exhaust lambda reading reports a result from exhaust gases; it does not reveal the mixture at every point in the cylinder.
Implications for diagnosis and tuning
- Compare requested and actual low- and high-pressure values using correctly identified channels, units and operating conditions. Pressure tracking alone does not confirm injector spray, timing or actual mixture.
- Injection duration must fit the available crank-angle window. Higher engine speed and changes in fuel demand can reduce the available time; raising a requested quantity does not prove the system can deliver it.
- Pressure, injection timing, injector data, air charge and ignition interact. Follow the applicable ECU and engine documentation and validate with appropriate instrumentation and controlled testing; avoid transferring settings from another engine or software version.
- Fuel vaporisation can cool the charge, but its effect depends on the injection and engine design. It does not remove the need to control knock and component temperatures.
Service: Direct-injection systems can retain hazardous high pressure. Use the vehicle manufacturer's depressurisation procedure and specified tools before opening any part of the fuel circuit. Delphi: removing and refitting GDI injectors.
Related reading: Petrol fuel-delivery layouts, Mixture tuning: AFR and lambda and MED9.1 injector calibration and injection windows.