Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Other Upgrades
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

What individual throttles do

Individual throttle bodies (ITBs) provide a separate throttle valve for each cylinder or intake runner. The valves can share a housing and linkage; “individual” describes control of each runner, not necessarily a separate casting or motor. A single throttle feeding a plenum is a different arrangement. A multiple-throttle engine can still have an airbox, a shared chamber, a central throttle or intake tuning valves.

With the throttle close to the inlet valve, the volume between them can be small. A change in opening can therefore change the pressure at the port quickly; response depends on the full intake and control system. ITBs do not eliminate tuned runner length: the trumpet, throttle, manifold and cylinder-head port all contribute to the path. Idle balance, linkage, air filtration and ECU calibration matter. See velocity stacks and intake runner tuning.

Reading the airflow path

“Before” and “after” can be confusing when a plenum sits physically above the stacks. Follow the air from filter to cylinder. These are schematic examples; parts and their order vary by engine.

LayoutTypical direction of airflowWhat the valves do
Shared throttleFilter → shared throttle → plenum → runners → intake valvesA common throttle meters air for the group.
Individual throttlesFilter / airbox → trumpet entries → individual throttles and runners → intake valvesEach cylinder has its own load-control throttle. The airbox may enclose the trumpets.
Central and individual throttlesFilter → central throttle → shared intake / runners → individual throttles → intake valvesBoth types can coexist. The central valve may be for backup rather than normal load control; its actual role and position must be checked for that engine.
Variable manifoldFilter → bank throttles → chambers → selected long or short paths → intake valvesAdditional butterflies can switch paths or connect chambers. They are not automatically individual driver-demand throttles.

Real systems may place trumpet mouths in a plenum and the individual throttle at another point in each runner. A butterfly visible in a runner is not enough to identify its purpose: follow the linkage or actuator and consult the correct service information. Two throttles in one air path can be used for different control or safety functions.

Ferrari: individual throttles and variable intake valves

The Ferrari F355 is an individual-throttle example: its illustrated Ferrari parts catalogue shows the throttle-body and accelerator assembly, and a contemporary road test describes an individual throttle for each cylinder. This does not establish an extra common throttle on every F355.

The Ferrari 360 Modena is an instructive different layout. Its workshop manual describes motor-driven inlet throttles, one for each bank. The variable intake has two chambers, short vertical ducts and longer ducts connected to the opposite bank. Electro-pneumatic valves select the intake arrangement, and another butterfly connects or separates the chambers. The manifold section identifies the runner butterflies and the separate air-compensating butterfly. Some runner valves select an alternative path rather than acting as a second load throttle in every airflow path. The manual says the manifold throttles are factory-adjusted; follow its service procedure rather than altering the settings by eye.

Consequently, seeing bank throttle bodies alongside individual trumpets and more butterflies on a Ferrari does not by itself establish two sets of pedal-controlled ITBs. Identify the model, trace each passage and separate the bank load throttles, runner-selection valves and chamber-connection valve. A valve between plenums controls their communication, not necessarily all the air entering a cylinder.

A central throttle with true individual throttles

Porsche's 2022 911 GT3 press kit, page 10, describes six individual throttle valves close to the intake valves and a retained central throttle. Porsche states that the central throttle is continuously open during normal operation and is a backup. This is a documented combination; the source does not establish its position relative to each trumpet mouth or the exact failure sequence. Do not assume the same strategy for Ferrari or another 911.

A different kind of dual-throttle system puts two valves in each individual bore. Suzuki's 2008 Hayabusa material describes primary rider-controlled butterflies and ECU-controlled secondary butterflies. That is not the same layout as one central throttle plus individual throttles.

Setting up and diagnosing ITBs

  • Synchronisation: check the condition of the linkage, return springs and vacuum leaks first. Balance individual airflow as specified for the hardware, then verify return to idle and full travel. Do not alter sealed factory stops or a factory-set variable-manifold mechanism without its instructions.
  • Load signal: a short individual runner can give a pulsing manifold-pressure signal. Some conversions use throttle position and rpm (alpha-N), a suitably damped common vacuum manifold, MAP, or a blend supported by the ECU. The correct method depends on the engine and controller; vacuum damping has its own response trade-off.
  • Ancillaries: plan for brake assistance, crankcase ventilation, idle air and purge connections as required, together with a clean, filtered air supply and a safe, unobstructed linkage. The Jenvey conversion guide discusses these integration tasks.
  • Calibration and testing: preserve the ECU's electronic throttle safety functions when present. Record the baseline, check air-fuel ratio and ignition against the appropriate limits, then compare matched dyno runs and part-load behaviour. An impressive induction sound or peak power number alone does not establish a better road setup.

Related: throttle body, throttle bodies and airflow and inlet manifolds and runner length.