What a velocity stack does
A velocity stack, inlet trumpet or bellmouth is the shaped entrance to an intake runner. Its rounded mouth guides air into the bore with less entry separation than a sharp edge and forms part of the runner geometry. It does not create energy or guarantee a fixed airflow increase. The opening also forms an acoustic boundary where pressure waves reflect; stack length, mouth shape, nearby surfaces, taper and the connected intake all affect the result.
In a firing engine, induction produces pressure waves as well as a mean airflow. In the simple open-runner example discussed in SAE paper 2007-01-0382, an expansion wave travels toward the mouth and is partly reflected as a compression wave. If a favourable pressure wave arrives at the valve while it is open, it can help cylinder filling. The phase and strength change with speed and configuration; a gain at one speed can accompany a loss elsewhere. This wave effect is distinct from air-column inertia, even though both influence filling.
Measure the whole path
The length of the removable trumpet alone is not the tuned tract length. Measure the approximate centreline from the trumpet mouth, through any throttle and manifold, into the cylinder-head port to the intake valve. Follow bends rather than measuring straight across the engine bay. Record where the bellmouth radius starts and ends, and whether the stated dimension includes it; suppliers do not all measure stack length in the same way.
Effective acoustic length is a model quantity, not simply the tape measurement. The mouth's end correction, an airbox or plenum, nearby walls, a tapered or branching port and valve timing affect the reflection. Jenvey describes tract length from valve to trumpet mouth and recommends testing for the engine and application. On a plenum system the runner mouth is often inside the plenum: the air filter or common throttle upstream is not automatically the end of each individual runner.
Length and engine speed
As a first trend, for the same geometry and a comparable resonance order, a longer effective runner generally moves a tuning feature toward lower rpm; shortening it moves that feature higher. It does not mean that longer always gives more low-speed torque or that one peak describes the whole curve. Different resonance orders can appear, and cam phasing, intake temperature, airbox, exhaust and load can move or reshape the result. The SAE study reviews tests showing the length trend and then measures how taper and entry radius affect a particular single-cylinder engine.
Worked illustration, not a cutting dimension
A simplified quarter-wave comparison in SAE 2007-01-0382 uses N ≈ 30c / (L × q), where N is rpm, c is sound speed in m/s, L is effective runner length in metres, and q is the selected frequency ratio; the paper discusses q = 3, 4 or 5 for the idealised model. For illustration only, set c = 343 m/s and q = 4:
| Assumed effective length | Illustrative predicted speed |
|---|---|
| 0.40 m | About 6,430 rpm |
| 0.48 m | About 5,360 rpm |
The calculation shows direction and scale for those assumptions, not the rpm at which a particular engine will make peak torque. Sound speed changes with temperature; effective length, valve events, plenum and wave order are not known accurately from a stack catalogue. Do not cut a stack to the calculated length without measurement and testing. The separate inlet-manifold page discusses a different, lumped Helmholtz approximation. Its volume, area and correction assumptions are not interchangeable with this pipe model.
Mouth shape, bore and clearance
A radiused mouth reduces entry loss; it also changes the boundary at which a wave reflects. In the cited SAE experiment, researchers compared 12 entry and taper configurations on one four-valve single-cylinder engine, at full throttle and specified conditions. The results show that mouth radius and taper can change volumetric efficiency and the shape of tuning peaks. Their best results and dimensions should not be treated as a universal bellmouth rule.
Stack diameter and taper must fit the entire system. An oversized passage is not a substitute for a correctly shaped port, throttle, cam and manifold; low-speed flow and control matter as well as peak restriction. When trumpets are enclosed, allow room around each mouth and test with the intended filter, lid and duct fitted. There is no universal clearance that guarantees the same result for every mouth and airbox. A filtered air supply protects the engine; an exposed open trumpet is not a street filtration strategy.
Fixed and variable trumpets
A fixed trumpet is a compromise across the operating range. Variable-length intakes change the effective path or switch paths so different pressure-wave behaviour can be used at different speeds and loads. Moving telescopic trumpets, switching between long and short passages, and opening a valve between plenum chambers are different mechanisms. Do not assume a plenum flap physically changes trumpet length.
The Ferrari 360 workshop manual describes short and longer intake paths selected by electro-pneumatic valves and a separate chamber-connection butterfly. Its layout is explained in individual throttle bodies and dual-throttle systems. Variable intake operation and calibration are specific to the engine.
Testing a change
- Set a target operating range and establish the existing configuration: complete tract length, bore, trumpet shape, cam timing, airbox, filter and ECU calibration.
- Measure repeatable baseline torque and power over the useful rpm range, with intake-air temperature, pressure and fuel mixture recorded. Check for faults, leaks and consistent throttle operation first.
- Compare interchangeable stack lengths while keeping other parts and test conditions as consistent as practical. Check fit and clearance across engine movement. Do not run without filtration or with unsecured parts near the intake.
- Compare the whole curve, repeat the baseline where practical, and verify fuelling, ignition and part-load behaviour after a hardware change. A shifted torque peak, a different temperature, or a changed filter can account for an apparent gain.
Related: inlet manifolds and runner length, individual throttle bodies, camshafts and valve timing and exhaust system tuning.