Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Remapping
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Land Rover

The 2.5-litre five-cylinder Td5 in the classic Defender and Discovery Series II uses electronically controlled, cam-driven unit injectors. Its fuel maps, ECU hardware and turbo control must be identified for the particular vehicle. This guide explains the map relationships described in Td5 specialist research, common upgrade choices and a workshop validation process. It does not provide a universal file, boost setting or safe torque figure. Land Rover Discovery Series II Td5 training manual.

Identify the engine, ECU and vehicle

Record VIN, model and year, market, engine code, manual or automatic transmission, ECU part number, software and tune identification, injector codes and all modifications. A vehicle can have a replacement engine or ECU, so check what is actually installed. The terms 10P/EU2 and 15P/EU3 are useful identifiers in the specialist material below, but do not establish that an arbitrary file will work in a particular vehicle. Defender and Discovery, manual and automatic, and emissions variants can use different calibrations.

  • MSB ECU: Nanocom describes the earlier MSB family as non-flash-programmable through its normal diagnostic functions. Physical memory work may be needed for tuning; determine whether a previous owner has already modified the unit.
  • NNN ECU: Nanocom describes the later NNN family as flash-programmable. Use a supported tool and a file matched to the ECU, engine, vehicle and configuration. Alive lists diagnostic-port remapping for selected NNN units; tool and software support must be checked for the actual unit.
  • Injector codes and security: retain the cylinder-specific injector settings and verify them when injectors are replaced or moved. ECU replacement may require configuration and immobiliser relearn. Do not assume a copied map or a donor ECU carries the right settings. Land Rover bulletin LT303-002 describes replacement and security-code checks for specific Discovery II Td5 cases.

Sources: Nanocom Lucas Td5 diagnostic guide; Alive Discovery Td5 remapping; Land Rover bulletin LT303-002.

How the main Td5 maps interact

DiscoTD5's analysis of Td5 files describes a fuel-quantity based path: driver demand is checked against smoke and torque limits; other corrections and limits then act before injection duration is determined. The following is a working model of that published analysis, not a factory description of every software version. Map names, axes, scale factors and selection logic depend on the exact file and definition. DiscoTD5: three core map groups; limiter stacking and version differences.

Map or functionRole in the researched Td5 filesPractical interpretation
Driver demandPedal demand and engine speed select a requested injection quantity, commonly displayed in mg per stroke. High- and low-range demand maps are described.A sharper pedal map can change response without necessarily increasing the maximum available fuel. Check the active range and full-load request as well as part-throttle drivability. Driver demand maps.
Smoke / air limitLimits fuel quantity against the available air and engine speed. The specialist describes a primary 10P smoke map and multiple 15P maps for different conditions.Air and fuel must be considered together; an inflated smoke limit cannot create air. Verify air calculation and active map for the exact software and driving condition. Smoke limiter maps.
Torque limitThe researched tables use engine speed to select a maximum requested fuel quantity; this is a quantity limit associated with torque, not a direct measurement of actual torque.More low-speed fuel can increase driveline loading. A raised limit has no effect wherever demand or another limit is lower. Torque limiters.
Fuel density correctionThe specialist describes fuel temperature, quantity and speed dependent correction before the duration calculation, with a limiting effect in some regions.Preserve the intended temperature compensation and assess its effect before interpreting a requested quantity. It should not be treated as a hidden general-purpose power control. Fuel density compensation.
Injection timing and durationFor the researched EU2 and EU3 calibrations, duration tables relate requested quantity and rpm to injector open time, with interpolation across timing/advance tables.Changing duration at a given displayed quantity can alter actual delivered fuel without changing the quantity the ECU believes it requested. This can undermine the interpretation of other limits; different injectors require matched, validated calibration. Injector duration discussion.
Target boost and wastegate controlDiscoTD5 describes a target table indexed by fuel quantity and rpm, plus duty and feedback functions for the Discovery wastegate modulator in the files examined.A boost target is not proof of measured pressure or compressor safety. Confirm the hardware is fitted and log actual behaviour. A standard Defender does not necessarily have Discovery's electronic modulator. Wastegate modulator control; Alive Defender modulator retrofit.

Illustrative limit example: at one operating point, if demand is 50 mg/stroke, the smoke limit is 46 and the torque limit is 44, the core comparison selects 44 before later corrections. Raising only the torque limit to 48 would leave 46 as the limiting value. These are invented numbers to explain the interaction, not Td5 settings. In real operation use the active maps and interpolated values, not just their largest cells.

Air calculation varies with strategy. DiscoTD5's reverse engineering describes EU2 fuel-demand calculations based on manifold pressure and intake temperature, and an EU3 strategy using mass-airflow information with a pressure/temperature fallback under certain fault conditions. Treat this as a finding for the researched files and verify the actual strategy and sensors. It also documents additional EU3 limiters, including a modelled turbo-speed limit; that is not a measured turbo shaft speed. DiscoTD5: airmass; EU3-specific limiters.

Reading and editing a calibration

  1. Identify the original hardware and software and read the file using a supported procedure. Save the original read and a separate copy of identifiers and configuration; determine whether the read is a calibration only or a full recoverable image. Confirm the tool's recovery procedure before writing.
  2. Open the exact file with an appropriate definition. Verify map identity, units, axis scaling, byte order and how the ECU chooses between variants. Community XDF or map labels are interpretations, not proof that every map or switch is correctly identified for every revision.
  3. Compare demand, smoke and torque limits over the relevant rpm and load range, including interpolation and other active limits. Inspect cold, high-temperature and altitude behaviour rather than flattening the protection functions. Maintain sensible part-throttle and low-range response for the vehicle's actual use.
  4. Check the timing, duration, boost and air-measurement interactions together. Retain fault detection and overboost protection; investigate an overboost cut, implausible sensor signal or loss of power rather than simply suppressing it. Use the correct checksum handling and tool instructions, then validate the result under load.

The specialist describes different map populations and limiter arrangements between EU2/EU3 and vehicle/transmission variants. A fuel quantity shown by a map editor is a modelled request, not a direct measurement at the injector. Changes to duration, injector hardware or sensor scaling can invalidate assumptions made by the other tables. DiscoTD5 limiter stacking; Td5 duration maps.

Common upgrades and what they require

UpgradePurpose and matching considerations
ECU remap or MSB memory workA calibration can improve response and output on a healthy engine. Decide whether the priority is towing, progressive off-road control or peak output, and provide tyre size, hardware, altitude and use to the tuner. “Stage 1” and “Stage 2” are supplier labels, not standard specifications. Alive Td5 file request.
Intercooler and charge hosesA larger or more efficient core can help manage charge temperature under sustained load. Check pressure drop, hose security, radiator airflow and packaging; vehicle equipment matters. AlliSport offers variants for oil-cooler or winch clearance and different pipe sizes on its Defender unit. Its advertised combined intercooler-and-tune gains are not evidence of the cooler's isolated gain. AlliSport Defender intercooler.
Hybrid or variable-geometry turboMore airflow potential comes with control, heat and driveline considerations. Alive's particular hybrid recommends a matched calibration, intercooler, intake and supporting hardware, and specifies a Discovery-type boost modulator for its control strategy. Its VNT kits have their own control and installation requirements; another manufacturer's actuator design can differ. Check oil supply and return, air filtration, exhaust leaks and the complete cooling system. Alive hybrid turbo; AlliSport VNT example.
Higher-range MAP sensorA wider-range sensor is useful only when required by a matched setup. The ECU must be calibrated for the sensor's actual transfer function and diagnostic range; verify readings against a reliable reference across the operating range. The sensor's pressure rating is not a boost target. Distinguish absolute manifold pressure from boost relative to ambient pressure. DiscoTD5 MAP sensor recalibration.
Clutch or automatic transmissionAdditional torque can expose a slipping clutch or existing transmission weakness. Check condition, intended duty and compatibility before selecting an uprated clutch or converter. Ashcroft offers a specific heavy-duty Td5 automatic converter; its existence does not mean every remap needs one. Ashcroft Td5 converter.
Intake and exhaustInspect the filter, intake path and exhaust for restriction or leaks; size changes should match the actual turbo and duty. Retain applicable emissions equipment and verify road legality. A louder exhaust or a high-flow filter alone does not establish a measured power gain.

For perspective, Alive advertises up to 210 hp and 450 Nm for its particular GTB450 Discovery kit on a healthy 15P with its specified tuning and supporting equipment. This is a supplier claim for that package, not an independently verified or universal result; it is not a target for a stock engine or different setup. Alive GTB450 Discovery kit.

Baseline, logging and acceptance

  1. Before changes: record diagnostic faults and freeze-frame information where available, ECU identification, injector codes and existing tune. Check service history, cooling, fuel supply, oil leaks or contamination at connectors, intake and intercooler hoses, exhaust manifold and turbo condition. Correct faults before increasing load. Nanocom lists Td5 sensor values and diagnostic functions; choose readings supported by the actual ECU. Nanocom guide.
  2. Establish comparable measurements: record ambient conditions, engine temperature, gear, tyre and vehicle configuration. On a suitable four-wheel-drive dynamometer or controlled road test, log rpm, throttle, manifold and ambient pressure, intake and coolant temperature, available airflow and fuelling parameters, and wastegate duty where the modulator is fitted and data is available. Compare logged boost with an independent gauge when diagnosing a sensor or calibration issue.
  3. Validate the whole operating range: compare baseline and revised runs, including part-throttle, low-speed pickup, transient response and sustained load relevant to towing or hills. Check smoke and fault codes, boost control, coolant and charge temperatures, and clutch or automatic shift behaviour. Add suitable exhaust-temperature, turbine-pressure or turbo-speed instrumentation when the build calls for it; do not confuse modelled values with measurements. Garrett recommends leak checking and instrumented turbo-system evaluation. Garrett turbo system optimisation.
  4. Finish and document: retain the original read and final file, configuration, checks and before/after results. Investigate any new fault, excessive smoke, surging, overboost, slipping or temperature problem and revise or return to a verified baseline. No single boost, EGT or torque number is a safe limit for every Td5 and its duty cycle.

Emissions and road use

Retain applicable manufacturer-fitted emissions equipment and check local rules before modifying the vehicle. In the UK MOT inspection, missing, obviously modified or obviously defective manufacturer-fitted emissions equipment is a major defect. A clean-looking exhaust or an MOT pass alone does not prove that a modified calibration meets all road-use requirements. DVSA MOT manual, emissions.

Related wiki pages