Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Bosch MED9.1
Applies to
Bosch MED9.1
Tool groups
None
Manufacturers
Audi, Volkswagen

Changes from revision 3 to revision 4

Removed text is struck through; added text is highlighted.

Scope and prerequisites

This guide concerns VAG EA113 2.0 FSI/TFSI MED9.1 research. Record the engine, ECU software, injector part number and revision, fuel, pump hardware and changes to the combustion chamber. Match definitions to the actual binary using the software matching guide. Establish the active lambda request and fuel-pressure behaviour before interpreting an injector correction.

Separate the injector functions

The table summarises Bosch RKTI 32.20.1, pages 1831–1837, in program 41W038_PQ35, 20 August 2004. It is a function reference for that implementation; selection logic, units and locations must be verified in the target software.The table summarises Bosch RKTI 32.20.1, pages 1831–1837, in program 41W038_PQ35, 20 August 2004. It is a function reference for that implementation; verify selection logic, units and locations in the target software.

FunctionRole to identify KRKATE and KLTIKRPRRelative fuel mass to effective injection time, with pressure-dependent flow correction. KLTVTSVPressure-dependent time offset added to the corrected effective time. KLHDEVCorrection of injector nonlinearity at short effective times. TIMINPMinimum injection-time limit. FKKVSFuel-system fine correction indexed by effective injection time and rpm.

In this document the relevant pressure difference is across the injector, between rail and combustion chamber. Compression-stroke injection includes a chamber-pressure calculation; substituting rail pressure or manifold boost for the curve's specified input changes its meaning. The KRKATE derivation also depends on per-cylinder displacement, characterised flow and its test conditions; KRKATE and KLTIKRPR must share the appropriate nominal-pressure basis. The same section also describes starting branches where FKKVS is excluded, so a warm-running correction need not fix cranking.

Interpreting the signed pressure-dependent offsetA June 2015 KLTVTSV discussion began with confusing axis data and assumptions about opening delay; a corrected axis definition was later reported. Contributors then explained the signed offset in terms of opening and closing contributions and distinguished duration offset from latency (forum explanations, not manufacturer documentation). The useful lesson is to identify what the calibrated time corrects before interpreting its sign. A negative entry alone does not prove a bad definition, and this explanation supplies no replacement curve for an unidentified injector.An April 2018 fuelling discussion treats FKKVS as a multiplier and cautions that injection-angle control already has window handling. A follow-up distinguishes KLTVTSV's pressure dependence from the voltage dependence familiar from ME7 TVUB. The complete MED9.1 path should be checked instead of transferring a port-injector calibration recipe.Injector swaps: reported outcomesIn one reported 079906036N case, newer RS4 injectors were fitted to a 2008 A4 2.0 FSI. An April 2015 positive report was followed by a May report of delayed cold starting, alongside concurrent throttle-body and airflow-model changes. In June, the same owner reported poor starting after copying MED17 timing/offset data, and another contributor reported no improvement from a suggested timing change. These observations support checking operating state and component identity; they do not establish a universal RS4-to-2.0 calibration.Flow-test conditions, spray-targeting and electrical-drive data should be obtained for the fitted part. Bosch Motorsport's HDEV 5.2 data sheet, pages 1–2, illustrates these separate component specifications; it does not establish compatibility of the reported injector with an OEM MED9.1 installation.Read the offset discussion through to its correctionThe June 2015 KLTVTSV discussion began with confusing axis data and assumptions about opening delay. The author later reported a corrected axis definition. On 9 June, prj explained the signed offset in terms of opening and closing contributions; nyet distinguished duration offset from latency. The useful lesson is to identify what the calibrated time corrects before interpreting its sign. A negative entry alone does not prove a bad definition, and this explanation supplies no replacement curve for an unidentified injector.The April 2018 fuelling discussion treats FKKVS as a multiplier and cautions that injection-angle control already has window handling. The follow-up distinguishes KLTVTSV's pressure dependence from the voltage dependence familiar from ME7 TVUB. Check the complete MED9.1 path instead of transferring a port-injector calibration recipe.Injector swaps: preserve the later outcomeIn the linked 079906036N case, ericpaulyoung described fitting newer RS4 injectors to a 2008 A4 2.0 FSI. An April 2015 positive report was followed by a May report of delayed cold starting, alongside concurrent throttle-body and airflow-model changes. In June the author reported poor starting after copying MED17 timing/offset data; another contributor reported no improvement from a suggested timing change. These observations support checking operating state and component identity; they do not establish a universal RS4-to-2.0 calibration.Obtain flow-test conditions, spray-targeting and electrical-drive data for the fitted part. Bosch Motorsport's HDEV 5.2 data sheet, pages 1–2, illustrates these separate component specifications; it does not establish compatibility of the forum injector with an OEM MED9.1 installation.

Injection duration and the available window

Bosch AWEA 27.20.0, pages 1807–1808, distinguishes start/end angle by injection type and describes conditional advance of homogeneous injection when an end boundary would be exceeded, with an advance limit. The active event, angle reference and limits must be established before phasing is changed. A simple time conversion is crank degrees = 0.006 × rpm × duration in milliseconds; this arithmetic does not identify the permitted injection window.Bosch AWEA 27.20.0, pages 1807–1808, distinguishes start/end angle by injection type and describes conditional advance of homogeneous injection when an end boundary would be exceeded, with an advance limit. Establish the active event, angle reference and limits before changing phasing. A simple time conversion is crank degrees = 0.006 × rpm × duration in milliseconds; this arithmetic does not identify the permitted injection window.

For a broad running error, verify injector characterisation and pressure basis before using a local correction map to conceal the mismatch. For an error concentrated at small pulses, examine offset, short-pulse correction and minimum-time limiting together; use component data and independent checks to distinguish them. For cold-start-only trouble, record starting temperature, cranking voltage/rpm, rail pressure, injection type, duration, phasing and misfires. A warm fuel-trim result is insufficient evidence for the starting branch. For a high-rpm shortfall, compare final lambda request, actual mixture, rail request/actual and the verified event duration/angles. Determine whether delivery, representation or the available window limits the result before adding load.

These checks are editorial diagnostic reasoning from the cited evidence. No injector scalar, minimum pulse or timing value is prescribed.Not establishedA universal RS4-to-2.0 injector calibration.Any injector scalar, minimum pulse or timing value.Sources and related pagesSources reviewed 16 November 2026. Forum attachments and the reported hardware were not independently tested. For separating intake/MAF errors from fuel-system correction, continue with MED9.1 intake comparison and fuel-trim diagnosis.These checks are editorial diagnostic reasoning from the cited evidence. No injector scalar, minimum pulse or timing value is prescribed. Forum attachments and the reported hardware were not independently tested. Sources reviewed 16 November 2026.For separating intake/MAF errors from fuel-system correction, continue with MED9.1 intake comparison and fuel-trim diagnosis.

For selected EA113 direct-injector products, part numbers and manufacturer flow specifications, see the EA113 and EA888 injector upgrade comparison. The comparison distinguishes injector test conditions from ECU calibration data.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: MED9.1 2.0 TFSI injector calibration and injection windows

Scope and prerequisites

This guide concerns VAG EA113 2.0 FSI/TFSI MED9.1 research. Record the engine, ECU software, injector part number and revision, fuel, pump hardware and changes to the combustion chamber. Match definitions to the actual binary using the software matching guide. Establish the active lambda request and fuel-pressure behaviour before interpreting an injector correction.

Separate the injector functions

The table summarises Bosch RKTI 32.20.1, pages 1831–1837, in program 41W038_PQ35, 20 August 2004. It is a function reference for that implementation; verify selection logic, units and locations in the target software.

FunctionRole to identify
KRKATE and KLTIKRPRRelative fuel mass to effective injection time, with pressure-dependent flow correction.
KLTVTSVPressure-dependent time offset added to the corrected effective time.
KLHDEVCorrection of injector nonlinearity at short effective times.
TIMINPMinimum injection-time limit.
FKKVSFuel-system fine correction indexed by effective injection time and rpm.

In this document the relevant pressure difference is across the injector, between rail and combustion chamber. Compression-stroke injection includes a chamber-pressure calculation; substituting rail pressure or manifold boost for the curve's specified input changes its meaning. The KRKATE derivation also depends on per-cylinder displacement, characterised flow and its test conditions; KRKATE and KLTIKRPR must share the appropriate nominal-pressure basis. The same section also describes starting branches where FKKVS is excluded, so a warm-running correction need not fix cranking.

Read the offset discussion through to its correction

The June 2015 KLTVTSV discussion began with confusing axis data and assumptions about opening delay. The author later reported a corrected axis definition. On 9 June, prj explained the signed offset in terms of opening and closing contributions; nyet distinguished duration offset from latency. The useful lesson is to identify what the calibrated time corrects before interpreting its sign. A negative entry alone does not prove a bad definition, and this explanation supplies no replacement curve for an unidentified injector.

The April 2018 fuelling discussion treats FKKVS as a multiplier and cautions that injection-angle control already has window handling. The follow-up distinguishes KLTVTSV's pressure dependence from the voltage dependence familiar from ME7 TVUB. Check the complete MED9.1 path instead of transferring a port-injector calibration recipe.

Injector swaps: preserve the later outcome

In the linked 079906036N case, ericpaulyoung described fitting newer RS4 injectors to a 2008 A4 2.0 FSI. An April 2015 positive report was followed by a May report of delayed cold starting, alongside concurrent throttle-body and airflow-model changes. In June the author reported poor starting after copying MED17 timing/offset data; another contributor reported no improvement from a suggested timing change. These observations support checking operating state and component identity; they do not establish a universal RS4-to-2.0 calibration.

Obtain flow-test conditions, spray-targeting and electrical-drive data for the fitted part. Bosch Motorsport's HDEV 5.2 data sheet, pages 1–2, illustrates these separate component specifications; it does not establish compatibility of the forum injector with an OEM MED9.1 installation.

Injection duration and the available window

Bosch AWEA 27.20.0, pages 1807–1808, distinguishes start/end angle by injection type and describes conditional advance of homogeneous injection when an end boundary would be exceeded, with an advance limit. Establish the active event, angle reference and limits before changing phasing. A simple time conversion is crank degrees = 0.006 × rpm × duration in milliseconds; this arithmetic does not identify the permitted injection window.

  1. For a broad running error, verify injector characterisation and pressure basis before using a local correction map to conceal the mismatch.
  2. For an error concentrated at small pulses, examine offset, short-pulse correction and minimum-time limiting together; use component data and independent checks to distinguish them.
  3. For cold-start-only trouble, record starting temperature, cranking voltage/rpm, rail pressure, injection type, duration, phasing and misfires. A warm fuel-trim result is insufficient evidence for the starting branch.
  4. For a high-rpm shortfall, compare final lambda request, actual mixture, rail request/actual and the verified event duration/angles. Determine whether delivery, representation or the available window limits the result before adding load.

These checks are editorial diagnostic reasoning from the cited evidence. No injector scalar, minimum pulse or timing value is prescribed. Forum attachments and the reported hardware were not independently tested. Sources reviewed 16 November 2026.

For separating intake/MAF errors from fuel-system correction, continue with MED9.1 intake comparison and fuel-trim diagnosis.

For selected EA113 direct-injector products, part numbers and manufacturer flow specifications, see the EA113 and EA888 injector upgrade comparison. The comparison distinguishes injector test conditions from ECU calibration data.

Revision 4: MED9.1 2.0 TFSI injector calibration and injection windows

Scope and prerequisites

This guide concerns VAG EA113 2.0 FSI/TFSI MED9.1 research. Record the engine, ECU software, injector part number and revision, fuel, pump hardware and changes to the combustion chamber. Match definitions to the actual binary using the software matching guide. Establish the active lambda request and fuel-pressure behaviour before interpreting an injector correction.

Separate the injector functions

The table summarises Bosch RKTI 32.20.1, pages 1831–1837, in program 41W038_PQ35, 20 August 2004. It is a function reference for that implementation; selection logic, units and locations must be verified in the target software.

FunctionRole to identify
KRKATE and KLTIKRPRRelative fuel mass to effective injection time, with pressure-dependent flow correction.
KLTVTSVPressure-dependent time offset added to the corrected effective time.
KLHDEVCorrection of injector nonlinearity at short effective times.
TIMINPMinimum injection-time limit.
FKKVSFuel-system fine correction indexed by effective injection time and rpm.

In this document the relevant pressure difference is across the injector, between rail and combustion chamber. Compression-stroke injection includes a chamber-pressure calculation; substituting rail pressure or manifold boost for the curve's specified input changes its meaning. The KRKATE derivation also depends on per-cylinder displacement, characterised flow and its test conditions; KRKATE and KLTIKRPR must share the appropriate nominal-pressure basis. The same section also describes starting branches where FKKVS is excluded, so a warm-running correction need not fix cranking.

Interpreting the signed pressure-dependent offset

A June 2015 KLTVTSV discussion began with confusing axis data and assumptions about opening delay; a corrected axis definition was later reported. Contributors then explained the signed offset in terms of opening and closing contributions and distinguished duration offset from latency (forum explanations, not manufacturer documentation). The useful lesson is to identify what the calibrated time corrects before interpreting its sign. A negative entry alone does not prove a bad definition, and this explanation supplies no replacement curve for an unidentified injector.

An April 2018 fuelling discussion treats FKKVS as a multiplier and cautions that injection-angle control already has window handling. A follow-up distinguishes KLTVTSV's pressure dependence from the voltage dependence familiar from ME7 TVUB. The complete MED9.1 path should be checked instead of transferring a port-injector calibration recipe.

Injector swaps: reported outcomes

In one reported 079906036N case, newer RS4 injectors were fitted to a 2008 A4 2.0 FSI. An April 2015 positive report was followed by a May report of delayed cold starting, alongside concurrent throttle-body and airflow-model changes. In June, the same owner reported poor starting after copying MED17 timing/offset data, and another contributor reported no improvement from a suggested timing change. These observations support checking operating state and component identity; they do not establish a universal RS4-to-2.0 calibration.

Flow-test conditions, spray-targeting and electrical-drive data should be obtained for the fitted part. Bosch Motorsport's HDEV 5.2 data sheet, pages 1–2, illustrates these separate component specifications; it does not establish compatibility of the reported injector with an OEM MED9.1 installation.

Injection duration and the available window

Bosch AWEA 27.20.0, pages 1807–1808, distinguishes start/end angle by injection type and describes conditional advance of homogeneous injection when an end boundary would be exceeded, with an advance limit. The active event, angle reference and limits must be established before phasing is changed. A simple time conversion is crank degrees = 0.006 × rpm × duration in milliseconds; this arithmetic does not identify the permitted injection window.

  1. For a broad running error, verify injector characterisation and pressure basis before using a local correction map to conceal the mismatch.
  2. For an error concentrated at small pulses, examine offset, short-pulse correction and minimum-time limiting together; use component data and independent checks to distinguish them.
  3. For cold-start-only trouble, record starting temperature, cranking voltage/rpm, rail pressure, injection type, duration, phasing and misfires. A warm fuel-trim result is insufficient evidence for the starting branch.
  4. For a high-rpm shortfall, compare final lambda request, actual mixture, rail request/actual and the verified event duration/angles. Determine whether delivery, representation or the available window limits the result before adding load.

These checks are editorial diagnostic reasoning from the cited evidence. No injector scalar, minimum pulse or timing value is prescribed.

Not established

  • A universal RS4-to-2.0 injector calibration.
  • Any injector scalar, minimum pulse or timing value.

Sources and related pages

Sources reviewed 16 November 2026. Forum attachments and the reported hardware were not independently tested. For separating intake/MAF errors from fuel-system correction, continue with MED9.1 intake comparison and fuel-trim diagnosis.

For selected EA113 direct-injector products, part numbers and manufacturer flow specifications, see the EA113 and EA888 injector upgrade comparison. The comparison distinguishes injector test conditions from ECU calibration data.