Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engines
Parent
Section level
Applies to
Bosch MED17.5
Tool groups
None
Manufacturers
Volkswagen Group

Scope: “Generation 2” is a convenient label used for later early-EA888 variants; market, installation and changes overlap. This page uses the specifically identified Audi 2.0 TFSI CAEB as an example, not a complete fitment list. Verify the engine code, market, vehicle, build date and ECU before applying any detail to another engine.

Engine and ECU identification

Audi SSP 922903, printed pp. 1–3, identifies its CAEB engine as a 1,984 cc inline-four direct-injection turbo engine with 82.5 × 92.8 mm bore and stroke and Bosch MED17.5 engine management. The same document describes a cast-iron block, chain-driven timing gear, balance shafts and four valves per cylinder. The generation label alone does not establish an exact MED17 subvariant, part number, software, calibration or vehicle fitment.

Audi's 2013 oil-consumption bulletin identifies specific CAEB examples in 2009–2011 A4, A5 and Q5 applications and lists multiple ECU software part numbers. The training document and service material show why a vehicle badge alone is insufficient: retain VIN, engine code, ECU part number and software version with a read or log. Use current manufacturer information for the particular car.

Variable valve lift and lubrication

In the CAEB described by SSP 922903, the intake cam has a camshaft adjuster, while Audi Valvelift (AVS) selects different exhaust-cam profiles. Electromagnetic actuators F366–F373 move cam elements; the ECU evaluates a feedback signal associated with a completed movement. Exhaust lift switching is not the same mechanism as intake cam phasing. These details are specific to the cited engine, not evidence of AVS on every Gen 2 engine. Audi SSP 922903, printed pp. 2, 4–12.

The same CAEB document describes a self-regulating oil pump with ECU-controlled oil-pressure regulating valve N428 and oil-pressure switches F22 and F378. The switches report threshold states, not a continuous physical pressure waveform. Check the actual hardware and current diagnostic procedure; compare a calibrated mechanical measurement under the specified conditions when directed by service information. An ECU output command alone does not establish oil pressure. SSP 922903, printed pp. 17–24.

MED17.5 and tuning implications

The CAEB ECU example has electronic throttle, direct injection, a hot-film air-mass sensor and map-controlled ignition with cylinder-selective knock control. Treat airflow, load, requested torque, measured or modelled pressure, ignition corrections and lambda as separate channels. ECU variants and hardware differ within the family; check definitions, units, pressure reference and software identity before using a map name or address. Audi SSP 922903, printed p. 2; Bosch MED17.5.

With a tune or hardware change, first record fuel quality, intake and turbo setup, injector and pump equipment, gearbox, original ECU and TCU versions, diagnostic faults and baseline logs. Compare matching pressure request and actual, fuel rail request and actual, lambda target and an appropriate measured signal, ignition/knock corrections, temperature and operating modes. When AVS or cam signals are available, verify the active mode; requested cam state is not proof of successful physical switching. Preserve protection and diagnose fuel, air and mechanical faults rather than masking them in calibration.

For example map names discussed for a particular MED17.5 wastegate case, see wastegate and boost-control diagnosis. They are forum-reported leads, not proven CAEB-specific symbols. For fuel-system checks and sensor caveats, see fuel pressure and lambda log review; that page's early transverse examples should not be assumed to share every CAEB component.

Oil-consumption diagnosis

Audi's 2013 bulletin 17 13 42 / 2027731 describes an oil-consumption complaint procedure for the listed CAEB vehicles, including a guided measurement and specific equipment/software checks. It is a historical, application-specific service example, not a diagnosis of every engine or an instruction to fit those parts to later cars. Verify the current bulletin and repair information for the vehicle, and check leaks and crankcase ventilation as part of the prescribed diagnosis.

Related: Bosch MED17 family · lambda requests and component protection · MED17.5 torque reporting. Manufacturer training documents are historical descriptions hosted on independent mirrors. Reviewed 17 November 2026.