Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Simos 8.4 and 8.5
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Simos 8.5 is a variant of the Siemens/Continental Simos 8 family. Tool and tuning-product listings identify it on examples of the supercharged 3.0 V6 TFSI. Confirm the ECU part number, hardware, software and calibration on the vehicle before selecting a definition or programming procedure.

Scope and applications

Alientech's Powergate vehicle list associates a 2011 Audi S4 Avant 3.0 TFSI CGWC with Simos 8.5. This is a supplier's product-coverage example, not proof that every CGWC vehicle uses the same ECU. The simos.app definitions index lists identifiers and boxcode combinations for Simos 8.5; a definition does not establish a flashing tool's support or validate a file.

Audi SSP 437 describes the belt-driven 3.0 V6 TFSI engine, its bypass and Simos 8 control. That programme identifies its own CAJA example only as Simos 8, without confirming an 8.5 suffix. Use its engine-system description as context and verify the installation being worked on.

Calibration and tools

The Main Patch map-switching reference covers custom functions for named Simos 8.5 software, including separate torque limits and ignition offsets per slot. These features are specific to that patch, not stock operation. Any guide or map definition must be matched to the exact software and the operating conditions checked in logs. The community Simos Suite reference is another research lead; its map descriptions and proposed numerical limits have not been independently validated.

The Simos Suite reference suggests scaling a table labelled maf_transfer in response to a lean mixture, but the linked guide does not establish the identification and validation of that table for a particular ECU software. Audi SSP 437 describes a separate CAJA example in which air mass is calculated from pressure and temperature signals, and names its controller only as Simos 8. Therefore verify the actual engine's fitted sensors, file-specific definitions, intake integrity and fuel supply before assuming a hot-film MAF sensor or applying a percentage correction. This comparison does not by itself establish the exact configuration of every 8.5 vehicle.

See Simos 8 supercharged 3.0 TFSI fuel pressure and lambda log review for fuel-system and bank-mixture diagnosis.

A named file and its advertised map labels

As a file-specific research lead, Auto-Remap lists calibration 8K5907551E 0004 as Simos 8.5 for an Audi Q5 CTVA, and advertises a CSV map pack with 106 named entries. The seller’s visible labels include calculated engine torque, clutch-protection torque limits, low- and high-speed torque requests, requested engine load, requested lambda, ignition maps and rail pressure. These are the seller’s group names and counts, not independently validated map definitions or proof of which functions are active.

The public page displays names but does not show map sizes, axes or addresses; it does not supply a separate ECU hardware or software identifier for the listing. Although it asks customers to match their read, the displayed calibration number alone cannot establish that the pack matches a particular ECU. Its advertised file is a WinOLS CSV export rather than a factory DAMOS or A2L, and the supplier says its original-file product is not a complete backup or EEPROM. Verify the complete identification, boundaries, scaling and function before using any definition; do not infer that all similarly labelled torque limits should be changed.

Research-tool and programming scope

The open-source Simos Suite project identifies Simos 8.5 on its documented C7 3.0 TFSI research target and describes ECU identification, fault-code and live-data access alongside a simulated ECU mode. The simulator is useful for exploring the interface without a vehicle; a successful simulated session is not evidence that a particular physical controller, interface or log channel is supported. The project describes itself as pre-1.0 and says its ECU/TCU flash-write controls are disabled in the graphical interface pending hardware validation. These are project-author statements, not independently verified vehicle tests; check the current version and its documentation.

For that project, its documentation describes the Simos 8.5 full-read and write route as bench/boot rather than the suite's OBD path. This limitation is specific to the project and does not rule out other tools' different procedures. Separately, the PCMflash manual, module 57, lists Simos 8.5 for virtual read, write and checksum check/correction; its virtual-read description says it retrieves a matching file from a server. The two statements describe different products and operations. A downloaded virtual original is not necessarily the modified content currently in the ECU, and a simulator or a calibration-only file is not proof of a complete flash or EEPROM backup. Verify the exact tool and ECU, file scope, checksum and a practical recovery method before programming.

Sources