Removed text is struck through; added text is highlighted.
Electrical load and engine torque
At idle, an alternator places a mechanical load on the engine while supplying the electrical system. A load-related idle disturbance can involve the belt drive, battery and charging system, ECU inputs, idle control, or unrelated air and fuel faults. The ECU's estimated alternator torque is a model input; it is not a direct measurement of engine output or alternator-shaft torque.
These calibration and measurement names come from community SC8S5031_C_OEM PWSL torque-loss, electrical-load and power-management cross-references. They are Simos 18.1 software examples, not proof that every 18.x car uses the same generator, signal source or feature. Match the engine, alternator, software, ASW/CAL, variant selection, signal source and units. Some descriptions and axes conflict. Neither map ranges nor examples provide recommended settings.
Alternator torque model examples
ip_tq_loss_alter[0] is labelled alternator torque loss, with n_32 in rpm and gen_load_egy_mng_can in percent as axes and Nm output. The output is a calculated model quantity, not a torque measurement. Establish the active index and source in the target.
ip_tq_loss_alter_dfm and ip_tq_loss_alter_dfm_2 are DFM-strategy variants indexed by engine speed and gen_load in percent, with Nm output. A description or map present in a file does not show which path is selected, or prove that a physical DFM signal is connected.
ip_tq_loss_alter_max[0] is labelled maximum alternator torque loss versus engine rpm. c_tq_loss_alter_st is an initial torque-loss value for engine starting, and c_tq_loss_alter_sub is a substitute value for missed CAN messages. They are distinct from an idle-speed target and a measured charging current. PWSL torque-loss reference.
ip_tq_loss_alter_ofs_ast is labelled alternator-load pre-control after start, output in Nm against t_ast in seconds and a temperature-labelled axis. Its second axis says NO_INPUT_QUANTITY, and its copied table caption describes a maximum torque loss instead. Verify the actual input and lookup before interpreting the map.
ip_lgrd_tq_loss_alter[0] is a torque-change limitation map with a declared Nm/10 ms output and an alternator-activation time axis in seconds; the second, torque-labelled axis has no declared input. Confirm task period and source rather than calling its values Nm/s. tq_loss_alter_1 and tq_loss_alter_tmp are runtime calculation signals, not base calibration maps.
Load input, filtering and replacement
The PWSL electrical-load reference describes ip_altpwm_fil as a filtering characteristic indexed by ducy_altpwm_fil_dif in percent. ip_fac_cor_altpwm_fil is an after-start correction factor with start coolant temperature tco_st and cyc_cast axes. A cycle count is not seconds; verify the target's counter definition and reset.
ip_gen_load_sub provides a substitute load against n_32 when the relevant load input fails in the documented strategy. lc_alter_src, lc_altpwm_clc_aut_act and lc_use_altpwm_can relate to source or variant selection. The runtime ducy_altpwm_raw, ducy_altpwm_fil and altpwm are different stages, not interchangeable live current measurements. Determine whether the matched vehicle actually receives the signal over hardware or CAN and whether fallback or an inhibit is active; a plausible filtered value alone cannot prove the physical alternator is supplying the expected output.
After-start load response
The PWSL power-management reference labels ip_t_min_alter_act an alternator activation delay after start, indexed by start coolant temperature tco_1_st in °C, output seconds. id_load_alter_resp_2 is a load-response-time curve indexed by t_alter_act, also in seconds. load_alter_resp_ems7 is a runtime load-response request, not measured charging current. Confirm selected branches and external battery-energy management; the ECU definition does not establish identical behaviour on every car.
The same reference lists full-load-related alternator-load conditions, including ip_pv_thd_n_alter_off, a pedal threshold against engine speed, and id_t_min_alter_off_fl, a gear-indexed time. These are conditional control terms, not a fixed power gain or a generic instruction to reduce charging. Any change requires understanding battery state, energy management and electrical demand for the actual vehicle.
Logging and diagnosis
Record ECU and engine identity, alternator and battery fitment, fault codes, battery condition and electrical consumers. Compare warm idle at repeatable conditions before and after switching on a known load; log rpm target and actual, battery voltage, available generator-load and torque-loss signals, air/fuel corrections, idle-control state and A/C request. Identify whether each channel is raw, filtered, estimated or substituted. An idle speed change or a changing alternator-load estimate is not alone evidence of a failed alternator or incorrect calibration.
HELLA's charging-system guidance discusses managed charging, generator control and vehicle-specific diagnostic tests. Use the current vehicle service procedure for battery, belt, wiring, grounds, communication and charging tests; operating voltage can vary with the control strategy and conditions. Do not infer a universal normal voltage from a single idle reading.
In a 2016 Mk7 GTI owner discussion, the owner described intermittent steering-assist and blower problems with changing logged voltage that were difficult to reproduce during workshop visits. They suspected a wiring or alternator issue; ECU software, root cause and a confirmed repair were not established. This is an example of capturing the fault under its actual conditions, not proof of a specific failure or that every voltage change is abnormal.
Related: idle control · A/C compressor torque and idle · torque model calibration · start-stop and restart. References reviewed 17 November 2026.
Open each version to inspect formatting, tables and photographs.
Revision 1: Simos 18 alternator load and idle torque compensation
Electrical load and engine torque
At idle, an alternator places a mechanical load on the engine while supplying the electrical system. A load-related idle disturbance can involve the belt drive, battery and charging system, ECU inputs, idle control, or unrelated air and fuel faults. The ECU's estimated alternator torque is a model input; it is not a direct measurement of engine output or alternator-shaft torque.
These calibration and measurement names come from community SC8S5031_C_OEM PWSL torque-loss, electrical-load and power-management cross-references. They are Simos 18.1 software examples, not proof that every 18.x car uses the same generator, signal source or feature. Match the engine, alternator, software, ASW/CAL, variant selection, signal source and units. Some descriptions and axes conflict. Neither map ranges nor examples provide recommended settings.
Alternator torque model examples
ip_tq_loss_alter[0] is labelled alternator torque loss, with n_32 in rpm and gen_load_egy_mng_can in percent as axes and Nm output. The output is a calculated model quantity, not a torque measurement. Establish the active index and source in the target.
ip_tq_loss_alter_dfm and ip_tq_loss_alter_dfm_2 are DFM-strategy variants indexed by engine speed and gen_load in percent, with Nm output. A description or map present in a file does not show which path is selected, or prove that a physical DFM signal is connected.
ip_tq_loss_alter_max[0] is labelled maximum alternator torque loss versus engine rpm. c_tq_loss_alter_st is an initial torque-loss value for engine starting, and c_tq_loss_alter_sub is a substitute value for missed CAN messages. They are distinct from an idle-speed target and a measured charging current. PWSL torque-loss reference.
ip_tq_loss_alter_ofs_ast is labelled alternator-load pre-control after start, output in Nm against t_ast in seconds and a temperature-labelled axis. Its second axis says NO_INPUT_QUANTITY, and its copied table caption describes a maximum torque loss instead. Verify the actual input and lookup before interpreting the map.
ip_lgrd_tq_loss_alter[0] is a torque-change limitation map with a declared Nm/10 ms output and an alternator-activation time axis in seconds; the second, torque-labelled axis has no declared input. Confirm task period and source rather than calling its values Nm/s. tq_loss_alter_1 and tq_loss_alter_tmp are runtime calculation signals, not base calibration maps.
Load input, filtering and replacement
The PWSL electrical-load reference describes ip_altpwm_fil as a filtering characteristic indexed by ducy_altpwm_fil_dif in percent. ip_fac_cor_altpwm_fil is an after-start correction factor with start coolant temperature tco_st and cyc_cast axes. A cycle count is not seconds; verify the target's counter definition and reset.
ip_gen_load_sub provides a substitute load against n_32 when the relevant load input fails in the documented strategy. lc_alter_src, lc_altpwm_clc_aut_act and lc_use_altpwm_can relate to source or variant selection. The runtime ducy_altpwm_raw, ducy_altpwm_fil and altpwm are different stages, not interchangeable live current measurements. Determine whether the matched vehicle actually receives the signal over hardware or CAN and whether fallback or an inhibit is active; a plausible filtered value alone cannot prove the physical alternator is supplying the expected output.
After-start load response
The PWSL power-management reference labels ip_t_min_alter_act an alternator activation delay after start, indexed by start coolant temperature tco_1_st in °C, output seconds. id_load_alter_resp_2 is a load-response-time curve indexed by t_alter_act, also in seconds. load_alter_resp_ems7 is a runtime load-response request, not measured charging current. Confirm selected branches and external battery-energy management; the ECU definition does not establish identical behaviour on every car.
The same reference lists full-load-related alternator-load conditions, including ip_pv_thd_n_alter_off, a pedal threshold against engine speed, and id_t_min_alter_off_fl, a gear-indexed time. These are conditional control terms, not a fixed power gain or a generic instruction to reduce charging. Any change requires understanding battery state, energy management and electrical demand for the actual vehicle.
Logging and diagnosis
Record ECU and engine identity, alternator and battery fitment, fault codes, battery condition and electrical consumers. Compare warm idle at repeatable conditions before and after switching on a known load; log rpm target and actual, battery voltage, available generator-load and torque-loss signals, air/fuel corrections, idle-control state and A/C request. Identify whether each channel is raw, filtered, estimated or substituted. An idle speed change or a changing alternator-load estimate is not alone evidence of a failed alternator or incorrect calibration.
HELLA's charging-system guidance discusses managed charging, generator control and vehicle-specific diagnostic tests. Use the current vehicle service procedure for battery, belt, wiring, grounds, communication and charging tests; operating voltage can vary with the control strategy and conditions. Do not infer a universal normal voltage from a single idle reading.
In a 2016 Mk7 GTI owner discussion, the owner described intermittent steering-assist and blower problems with changing logged voltage that were difficult to reproduce during workshop visits. They suspected a wiring or alternator issue; ECU software, root cause and a confirmed repair were not established. This is an example of capturing the fault under its actual conditions, not proof of a specific failure or that every voltage change is abnormal.
Related: idle control · A/C compressor torque and idle · torque model calibration · start-stop and restart. References reviewed 17 November 2026.
Revision 1: Simos 18 alternator load and idle torque compensation
Electrical load and engine torque
At idle, an alternator places a mechanical load on the engine while supplying the electrical system. A load-related idle disturbance can involve the belt drive, battery and charging system, ECU inputs, idle control, or unrelated air and fuel faults. The ECU's estimated alternator torque is a model input; it is not a direct measurement of engine output or alternator-shaft torque.
These calibration and measurement names come from community SC8S5031_C_OEM PWSL torque-loss, electrical-load and power-management cross-references. They are Simos 18.1 software examples, not proof that every 18.x car uses the same generator, signal source or feature. Match the engine, alternator, software, ASW/CAL, variant selection, signal source and units. Some descriptions and axes conflict. Neither map ranges nor examples provide recommended settings.
Alternator torque model examples
ip_tq_loss_alter[0] is labelled alternator torque loss, with n_32 in rpm and gen_load_egy_mng_can in percent as axes and Nm output. The output is a calculated model quantity, not a torque measurement. Establish the active index and source in the target.
ip_tq_loss_alter_dfm and ip_tq_loss_alter_dfm_2 are DFM-strategy variants indexed by engine speed and gen_load in percent, with Nm output. A description or map present in a file does not show which path is selected, or prove that a physical DFM signal is connected.
ip_tq_loss_alter_max[0] is labelled maximum alternator torque loss versus engine rpm. c_tq_loss_alter_st is an initial torque-loss value for engine starting, and c_tq_loss_alter_sub is a substitute value for missed CAN messages. They are distinct from an idle-speed target and a measured charging current. PWSL torque-loss reference.
ip_tq_loss_alter_ofs_ast is labelled alternator-load pre-control after start, output in Nm against t_ast in seconds and a temperature-labelled axis. Its second axis says NO_INPUT_QUANTITY, and its copied table caption describes a maximum torque loss instead. Verify the actual input and lookup before interpreting the map.
ip_lgrd_tq_loss_alter[0] is a torque-change limitation map with a declared Nm/10 ms output and an alternator-activation time axis in seconds; the second, torque-labelled axis has no declared input. Confirm task period and source rather than calling its values Nm/s. tq_loss_alter_1 and tq_loss_alter_tmp are runtime calculation signals, not base calibration maps.
Load input, filtering and replacement
The PWSL electrical-load reference describes ip_altpwm_fil as a filtering characteristic indexed by ducy_altpwm_fil_dif in percent. ip_fac_cor_altpwm_fil is an after-start correction factor with start coolant temperature tco_st and cyc_cast axes. A cycle count is not seconds; verify the target's counter definition and reset.
ip_gen_load_sub provides a substitute load against n_32 when the relevant load input fails in the documented strategy. lc_alter_src, lc_altpwm_clc_aut_act and lc_use_altpwm_can relate to source or variant selection. The runtime ducy_altpwm_raw, ducy_altpwm_fil and altpwm are different stages, not interchangeable live current measurements. Determine whether the matched vehicle actually receives the signal over hardware or CAN and whether fallback or an inhibit is active; a plausible filtered value alone cannot prove the physical alternator is supplying the expected output.
After-start load response
The PWSL power-management reference labels ip_t_min_alter_act an alternator activation delay after start, indexed by start coolant temperature tco_1_st in °C, output seconds. id_load_alter_resp_2 is a load-response-time curve indexed by t_alter_act, also in seconds. load_alter_resp_ems7 is a runtime load-response request, not measured charging current. Confirm selected branches and external battery-energy management; the ECU definition does not establish identical behaviour on every car.
The same reference lists full-load-related alternator-load conditions, including ip_pv_thd_n_alter_off, a pedal threshold against engine speed, and id_t_min_alter_off_fl, a gear-indexed time. These are conditional control terms, not a fixed power gain or a generic instruction to reduce charging. Any change requires understanding battery state, energy management and electrical demand for the actual vehicle.
Logging and diagnosis
Record ECU and engine identity, alternator and battery fitment, fault codes, battery condition and electrical consumers. Compare warm idle at repeatable conditions before and after switching on a known load; log rpm target and actual, battery voltage, available generator-load and torque-loss signals, air/fuel corrections, idle-control state and A/C request. Identify whether each channel is raw, filtered, estimated or substituted. An idle speed change or a changing alternator-load estimate is not alone evidence of a failed alternator or incorrect calibration.
HELLA's charging-system guidance discusses managed charging, generator control and vehicle-specific diagnostic tests. Use the current vehicle service procedure for battery, belt, wiring, grounds, communication and charging tests; operating voltage can vary with the control strategy and conditions. Do not infer a universal normal voltage from a single idle reading.
In a 2016 Mk7 GTI owner discussion, the owner described intermittent steering-assist and blower problems with changing logged voltage that were difficult to reproduce during workshop visits. They suspected a wiring or alternator issue; ECU software, root cause and a confirmed repair were not established. This is an example of capturing the fault under its actual conditions, not proof of a specific failure or that every voltage change is abnormal.
Related: idle control · A/C compressor torque and idle · torque model calibration · start-stop and restart. References reviewed 17 November 2026.