Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Simos 18
Applies to
Simos 18.1
Tool groups
None
Manufacturers
Volkswagen Group

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Transient boost is a coordinated control problem

After a rapid load request, pressure upstream of the throttle (PUT), wastegate command and actuator feedback can change at different rates. A brief target-to-actual gap does not identify a fault by itself. Distinguish a pressure setpoint that is reduced by torque or protection from an actuator that fails to reach its command, and from pressure that fails to follow an actuator that is moving correctly. EcuTek's EA888 Mk7 tuning guide describes a modelled wastegate position and reports that a hybrid turbo can require controller and position-setpoint calibration. This is hardware- and software-specific; it is not a direction to copy another turbo's tables or remove speed protection.

The examples below come from community-extracted SC8S5031_C_OEM minimum-time control and boost-pressure control references. They are Simos 18.1 research leads, not established active functions in all variants. Confirm ECU, engine and turbo, ASW/CAL, selectors, units, task rates, signs and any installed patch against matched definitions. A logger label or representable range is not a verified operating limit.

Minimum-time or open-loop pressure control

The minimum-time function includes a time-based open-loop PUT control sequence. In the cited implementation fac_pow_put_ctl_t_min is its runtime control value, while state_put_opl_ctl and state_put_opl_ctl_min_max describe the sequence and its deviation-search state. These are status or calculated values, not maps; do not assign state numbers from another software version. put_lpf_put_opl_ctl is filtered upstream-throttle pressure, and put_sp_put_opl_ctl_1 is the stored setpoint at a particular transition. Both are hPa in the reference, but neither alone proves sensor accuracy or actuator movement. Minimum-time function reference.

ip_t_put_opl_ctl_1 is an open-loop control time-threshold map in seconds, indexed by engine speed n and gear. The documented equation also includes an adaptive factor, so the map entry is not necessarily the resulting time. ip_fac_t_put_opl_ctl_2 is a factor for a second time threshold against speed and gear; c_t_put_opl_ctl_2_min and c_t_put_opl_ctl_2_max are scalar duration bounds in seconds. The source calls this minimum open-loop control: “minimum” here is a control state, not a generic minimum boost or a universal safety margin. c_amp_min_put_opl_ctl and c_n_max_put_opl_ctl are ambient-pressure and engine-speed conditions for activation. c_put_dif_state_put_opl_ctl_0 concerns cancellation on a pressure-control deviation. Establish pressure difference direction and the complete enabling logic before interpreting them. ip_fac_put_sp_inc_1_put_opl_ctl and ip_fac_put_sp_inc_2_put_opl_ctl are duration-weighting curves. Their axis inputs are marked NO_INPUT_QUANTITY in the extraction, so confirm the actual lookup and scaling instead of assuming a particular boost unit.

Learned timing versus actuator learning

ip_ad_fac_t_1_put_opl_ctl and ip_ad_fac_t_2_put_opl_ctl are separate adaptive factor maps for the beginning and duration of the minimum open-loop phase, indexed by speed and gear in this example. ip_fac_t_1_ad_inc_put_opl_ctl and ip_fac_t_2_ad_inc_put_opl_ctl describe increments against put_dif_min_put_opl_ctl in hPa. c_gear_put_opl_ctl_ad is a gear bitmask for adaptation; the reference says it must match the relevant gear breakpoints. The runtime t_put_opl_ctl_1_thd and t_put_opl_ctl_2_thd describe calculated timing thresholds, rather than the base map. Minimum-time reference.

This adaptation is distinct from both ip_ad_fac_bpa_sp, the separate boost-pressure actuator pre-control adaptation, and tester-requested electric wastegate end-stop learning. A successful stop learn does not prove an accurate pressure response, and clearing learned timing does not fix a mechanical, wiring or scaling fault. Record the current values and conditions before any service-directed reset; establish whether a tuning patch uses the stock path.

Small and large load changes

In the SC8S5031 boost-control application reference, ip_fac_put_ctl_stat is a weighting curve; the documented expression uses put_sp - put_sp_prev, although its axis metadata is NO_INPUT_QUANTITY. fac_put_ctl_stat is the runtime weighting factor. fac_pow_put_ctl_i_rgl_stat and fac_pow_put_ctl_p_d_rgl_stat are listed for small load steps; their _step counterparts are listed for large load steps. These are calculated controller contributions, not physical wastegate angles or editable gain tables.

ip_crlc_fac_pow_put_ctl_p_d is a low-pass filter coefficient against rpm for the P/D contribution; c_fac_pow_put_ctl_i_stnd and c_fac_pow_put_ctl_p_d_stnd scale the respective controller maps in this extraction. Do not infer the active response from one value alone: log controller state, relevant weighting, target, actuator request and actual together. Some source captions conflict or omit dimensions; verify the matched A2L and implementation before changing any field.

Diagnosing overshoot after changes

Identify the ECU calibration, boost-control patch, turbo and actuator; capture faults and freeze-frame. Check pressure-sensor scaling, electrical supply, linkage travel and applicable end-stop basic settings before changing control parameters. Where available compare synchronised upstream-throttle pressure target and actual, manifold pressure, atmospheric pressure, pedal, throttle, gear, rpm, wastegate request and feedback, controller terms and protection/intervention flags. Match sensor location and absolute versus gauge pressure; check sample rate and filtering. Log fuel pressure and lambda as well when assessing load operation. Compare similar warm conditions and load changes. A fast overshoot with a correctly tracking actuator, an actuator that cannot follow its request, and a reduced target are different diagnostic paths. Use a controlled facility and stop investigating under load if serious faults or abnormal behaviour appear. Do not raise thresholds to conceal a repeatable physical or control fault.

A Mk7 GTI IS38-swap owner reported intermittent P0234 and EPC under hard acceleration, stated that actuator adaptation had not initially been performed, and later reported improvement after changing the actuator setting. This is a single unverified account without complete calibration and test conditions. It does not establish a safe adjustment value or prove the cause; follow the actual turbo and vehicle service procedure.

Related: wastegate and boost control · electric actuator adaptation · underboost diagnosis · bigger turbo tuning · turbocharger protection. References reviewed 17 November 2026.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Simos 18 transient boost control and adaptation

Transient boost is a coordinated control problem

After a rapid load request, pressure upstream of the throttle (PUT), wastegate command and actuator feedback can change at different rates. A brief target-to-actual gap does not identify a fault by itself. Distinguish a pressure setpoint that is reduced by torque or protection from an actuator that fails to reach its command, and from pressure that fails to follow an actuator that is moving correctly. EcuTek's EA888 Mk7 tuning guide describes a modelled wastegate position and reports that a hybrid turbo can require controller and position-setpoint calibration. This is hardware- and software-specific; it is not a direction to copy another turbo's tables or remove speed protection.

The examples below come from community-extracted SC8S5031_C_OEM minimum-time control and boost-pressure control references. They are Simos 18.1 research leads, not established active functions in all variants. Confirm ECU, engine and turbo, ASW/CAL, selectors, units, task rates, signs and any installed patch against matched definitions. A logger label or representable range is not a verified operating limit.

Minimum-time or open-loop pressure control

The minimum-time function includes a time-based open-loop PUT control sequence. In the cited implementation fac_pow_put_ctl_t_min is its runtime control value, while state_put_opl_ctl and state_put_opl_ctl_min_max describe the sequence and its deviation-search state. These are status or calculated values, not maps; do not assign state numbers from another software version. put_lpf_put_opl_ctl is filtered upstream-throttle pressure, and put_sp_put_opl_ctl_1 is the stored setpoint at a particular transition. Both are hPa in the reference, but neither alone proves sensor accuracy or actuator movement. Minimum-time function reference.

  • ip_t_put_opl_ctl_1 is an open-loop control time-threshold map in seconds, indexed by engine speed n and gear. The documented equation also includes an adaptive factor, so the map entry is not necessarily the resulting time.
  • ip_fac_t_put_opl_ctl_2 is a factor for a second time threshold against speed and gear; c_t_put_opl_ctl_2_min and c_t_put_opl_ctl_2_max are scalar duration bounds in seconds. The source calls this minimum open-loop control: “minimum” here is a control state, not a generic minimum boost or a universal safety margin.
  • c_amp_min_put_opl_ctl and c_n_max_put_opl_ctl are ambient-pressure and engine-speed conditions for activation. c_put_dif_state_put_opl_ctl_0 concerns cancellation on a pressure-control deviation. Establish pressure difference direction and the complete enabling logic before interpreting them.
  • ip_fac_put_sp_inc_1_put_opl_ctl and ip_fac_put_sp_inc_2_put_opl_ctl are duration-weighting curves. Their axis inputs are marked NO_INPUT_QUANTITY in the extraction, so confirm the actual lookup and scaling instead of assuming a particular boost unit.

Learned timing versus actuator learning

ip_ad_fac_t_1_put_opl_ctl and ip_ad_fac_t_2_put_opl_ctl are separate adaptive factor maps for the beginning and duration of the minimum open-loop phase, indexed by speed and gear in this example. ip_fac_t_1_ad_inc_put_opl_ctl and ip_fac_t_2_ad_inc_put_opl_ctl describe increments against put_dif_min_put_opl_ctl in hPa. c_gear_put_opl_ctl_ad is a gear bitmask for adaptation; the reference says it must match the relevant gear breakpoints. The runtime t_put_opl_ctl_1_thd and t_put_opl_ctl_2_thd describe calculated timing thresholds, rather than the base map. Minimum-time reference.

This adaptation is distinct from both ip_ad_fac_bpa_sp, the separate boost-pressure actuator pre-control adaptation, and tester-requested electric wastegate end-stop learning. A successful stop learn does not prove an accurate pressure response, and clearing learned timing does not fix a mechanical, wiring or scaling fault. Record the current values and conditions before any service-directed reset; establish whether a tuning patch uses the stock path.

Small and large load changes

In the SC8S5031 boost-control application reference, ip_fac_put_ctl_stat is a weighting curve; the documented expression uses put_sp - put_sp_prev, although its axis metadata is NO_INPUT_QUANTITY. fac_put_ctl_stat is the runtime weighting factor. fac_pow_put_ctl_i_rgl_stat and fac_pow_put_ctl_p_d_rgl_stat are listed for small load steps; their _step counterparts are listed for large load steps. These are calculated controller contributions, not physical wastegate angles or editable gain tables.

ip_crlc_fac_pow_put_ctl_p_d is a low-pass filter coefficient against rpm for the P/D contribution; c_fac_pow_put_ctl_i_stnd and c_fac_pow_put_ctl_p_d_stnd scale the respective controller maps in this extraction. Do not infer the active response from one value alone: log controller state, relevant weighting, target, actuator request and actual together. Some source captions conflict or omit dimensions; verify the matched A2L and implementation before changing any field.

Diagnosing overshoot after changes

  1. Identify the ECU calibration, boost-control patch, turbo and actuator; capture faults and freeze-frame. Check pressure-sensor scaling, electrical supply, linkage travel and applicable end-stop basic settings before changing control parameters.
  2. Where available compare synchronised upstream-throttle pressure target and actual, manifold pressure, atmospheric pressure, pedal, throttle, gear, rpm, wastegate request and feedback, controller terms and protection/intervention flags. Match sensor location and absolute versus gauge pressure; check sample rate and filtering. Log fuel pressure and lambda as well when assessing load operation.
  3. Compare similar warm conditions and load changes. A fast overshoot with a correctly tracking actuator, an actuator that cannot follow its request, and a reduced target are different diagnostic paths. Use a controlled facility and stop investigating under load if serious faults or abnormal behaviour appear. Do not raise thresholds to conceal a repeatable physical or control fault.

A Mk7 GTI IS38-swap owner reported intermittent P0234 and EPC under hard acceleration, stated that actuator adaptation had not initially been performed, and later reported improvement after changing the actuator setting. This is a single unverified account without complete calibration and test conditions. It does not establish a safe adjustment value or prove the cause; follow the actual turbo and vehicle service procedure.

Related: wastegate and boost control · electric actuator adaptation · underboost diagnosis · bigger turbo tuning · turbocharger protection. References reviewed 17 November 2026.

Revision 1: Simos 18 transient boost control and adaptation

Transient boost is a coordinated control problem

After a rapid load request, pressure upstream of the throttle (PUT), wastegate command and actuator feedback can change at different rates. A brief target-to-actual gap does not identify a fault by itself. Distinguish a pressure setpoint that is reduced by torque or protection from an actuator that fails to reach its command, and from pressure that fails to follow an actuator that is moving correctly. EcuTek's EA888 Mk7 tuning guide describes a modelled wastegate position and reports that a hybrid turbo can require controller and position-setpoint calibration. This is hardware- and software-specific; it is not a direction to copy another turbo's tables or remove speed protection.

The examples below come from community-extracted SC8S5031_C_OEM minimum-time control and boost-pressure control references. They are Simos 18.1 research leads, not established active functions in all variants. Confirm ECU, engine and turbo, ASW/CAL, selectors, units, task rates, signs and any installed patch against matched definitions. A logger label or representable range is not a verified operating limit.

Minimum-time or open-loop pressure control

The minimum-time function includes a time-based open-loop PUT control sequence. In the cited implementation fac_pow_put_ctl_t_min is its runtime control value, while state_put_opl_ctl and state_put_opl_ctl_min_max describe the sequence and its deviation-search state. These are status or calculated values, not maps; do not assign state numbers from another software version. put_lpf_put_opl_ctl is filtered upstream-throttle pressure, and put_sp_put_opl_ctl_1 is the stored setpoint at a particular transition. Both are hPa in the reference, but neither alone proves sensor accuracy or actuator movement. Minimum-time function reference.

  • ip_t_put_opl_ctl_1 is an open-loop control time-threshold map in seconds, indexed by engine speed n and gear. The documented equation also includes an adaptive factor, so the map entry is not necessarily the resulting time.
  • ip_fac_t_put_opl_ctl_2 is a factor for a second time threshold against speed and gear; c_t_put_opl_ctl_2_min and c_t_put_opl_ctl_2_max are scalar duration bounds in seconds. The source calls this minimum open-loop control: “minimum” here is a control state, not a generic minimum boost or a universal safety margin.
  • c_amp_min_put_opl_ctl and c_n_max_put_opl_ctl are ambient-pressure and engine-speed conditions for activation. c_put_dif_state_put_opl_ctl_0 concerns cancellation on a pressure-control deviation. Establish pressure difference direction and the complete enabling logic before interpreting them.
  • ip_fac_put_sp_inc_1_put_opl_ctl and ip_fac_put_sp_inc_2_put_opl_ctl are duration-weighting curves. Their axis inputs are marked NO_INPUT_QUANTITY in the extraction, so confirm the actual lookup and scaling instead of assuming a particular boost unit.

Learned timing versus actuator learning

ip_ad_fac_t_1_put_opl_ctl and ip_ad_fac_t_2_put_opl_ctl are separate adaptive factor maps for the beginning and duration of the minimum open-loop phase, indexed by speed and gear in this example. ip_fac_t_1_ad_inc_put_opl_ctl and ip_fac_t_2_ad_inc_put_opl_ctl describe increments against put_dif_min_put_opl_ctl in hPa. c_gear_put_opl_ctl_ad is a gear bitmask for adaptation; the reference says it must match the relevant gear breakpoints. The runtime t_put_opl_ctl_1_thd and t_put_opl_ctl_2_thd describe calculated timing thresholds, rather than the base map. Minimum-time reference.

This adaptation is distinct from both ip_ad_fac_bpa_sp, the separate boost-pressure actuator pre-control adaptation, and tester-requested electric wastegate end-stop learning. A successful stop learn does not prove an accurate pressure response, and clearing learned timing does not fix a mechanical, wiring or scaling fault. Record the current values and conditions before any service-directed reset; establish whether a tuning patch uses the stock path.

Small and large load changes

In the SC8S5031 boost-control application reference, ip_fac_put_ctl_stat is a weighting curve; the documented expression uses put_sp - put_sp_prev, although its axis metadata is NO_INPUT_QUANTITY. fac_put_ctl_stat is the runtime weighting factor. fac_pow_put_ctl_i_rgl_stat and fac_pow_put_ctl_p_d_rgl_stat are listed for small load steps; their _step counterparts are listed for large load steps. These are calculated controller contributions, not physical wastegate angles or editable gain tables.

ip_crlc_fac_pow_put_ctl_p_d is a low-pass filter coefficient against rpm for the P/D contribution; c_fac_pow_put_ctl_i_stnd and c_fac_pow_put_ctl_p_d_stnd scale the respective controller maps in this extraction. Do not infer the active response from one value alone: log controller state, relevant weighting, target, actuator request and actual together. Some source captions conflict or omit dimensions; verify the matched A2L and implementation before changing any field.

Diagnosing overshoot after changes

  1. Identify the ECU calibration, boost-control patch, turbo and actuator; capture faults and freeze-frame. Check pressure-sensor scaling, electrical supply, linkage travel and applicable end-stop basic settings before changing control parameters.
  2. Where available compare synchronised upstream-throttle pressure target and actual, manifold pressure, atmospheric pressure, pedal, throttle, gear, rpm, wastegate request and feedback, controller terms and protection/intervention flags. Match sensor location and absolute versus gauge pressure; check sample rate and filtering. Log fuel pressure and lambda as well when assessing load operation.
  3. Compare similar warm conditions and load changes. A fast overshoot with a correctly tracking actuator, an actuator that cannot follow its request, and a reduced target are different diagnostic paths. Use a controlled facility and stop investigating under load if serious faults or abnormal behaviour appear. Do not raise thresholds to conceal a repeatable physical or control fault.

A Mk7 GTI IS38-swap owner reported intermittent P0234 and EPC under hard acceleration, stated that actuator adaptation had not initially been performed, and later reported improvement after changing the actuator setting. This is a single unverified account without complete calibration and test conditions. It does not establish a safe adjustment value or prove the cause; follow the actual turbo and vehicle service procedure.

Related: wastegate and boost control · electric actuator adaptation · underboost diagnosis · bigger turbo tuning · turbocharger protection. References reviewed 17 November 2026.