Page organisation in this revision
- Page type
- Technical article
- Subject
- Tuning
- Parent
- Simos 18
- Applies to
- Simos 18.1
- Tool groups
- None
- Manufacturers
- Volkswagen Group
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Scope and physical background
Wall-film compensation describes dynamic changes in fuel retained on surfaces and later vaporised. A transient fuel request can therefore differ from the fuel reaching combustion immediately. The intake-manifold film and combustion-chamber film are separate model paths in the SC8S5031_C_OEM FMSP cross-reference; the controller's film masses and correction are estimates, not physical film sensors. A general port-injection wall-wetting model is described by Linköping University, but its equations are background, not proof that Simos implements the same model.
The ECU names below are community-extracted Simos 18.1 examples, not universal calibrations. Match ASW, CAL, A2L, combustion-mode index, units and active branches. Some labels and copied narratives conflict. The presence of an MPI map is not proof that a car has port injectors: Audi SSP 920243 describes both dual-injection and DI-only EA888 Gen3 configurations. Do not assume all 18.x variants or retrofit controllers use these paths identically.
Fuel deposited in the model
ip_fac_mff_wf_hpdi[1][1] describes a factor for distributing high-pressure DI fuel to wall-film models; axes are engine speed n_32 in rpm and basic fuel mass mff_bas in mg/stroke. ip_fac_mff_wf_mpi[1][1] is the corresponding port-injected-fuel factor, indexed by rpm and intake manifold pressure prs_im in hPa. Neither is a DI/MPI overall fuel-split target.
ip_fac_mff_wf_cmbc_temp_cor and ip_fac_mff_wf_im_temp_cor are temperature corrections for fuel added to the chamber and manifold film paths. In this extraction both use tia_im and coolant temperature tco in degrees C. They are model factors, not injector dead-time tables or physical wall-temperature measurements.
id_idx_cal_wf selects film-calibration tables by combustion mode, while idx_cal_wf is the runtime index. Its axis input is labelled NO_INPUT_QUANTITY in the extraction. Confirm indexing and configured modes before deciding which array entry applies. FMSP field descriptions and axes.
Evaporation and correction
ip_fac_mwf_vap_cmbc[1] is an operating-point factor for the chamber film, indexed by rpm and mff_bas; ip_fac_mwf_vap_im[1] is the manifold counterpart, indexed by rpm and prs_im. The chamber entry's copied table prose describes MPI split rather than vaporisation; confirm its actual function against matched source/definition.
ip_fac_mwf_vap_cmbc_temp_cor and ip_fac_mwf_vap_im_temp_cor are temperature-related vaporisation factors with tia_im and tco axes. They are distinct from the temperature factors for fuel deposited in the film.
ip_mff_vap_wf_im[1] and ip_mff_vap_wf_cmbc[1] describe manifold and chamber evaporation behaviour; corresponding ip_mff_vap_wf_im_ivs[1] and ip_mff_vap_wf_cmbc_ivs[1] are inverse curves. Axis inputs are marked NO_INPUT_QUANTITY; confirm scaling, lookup and inverse relationship in the actual software. The reference says the inverse is derived from the forward characteristic, so treat the pair as linked rather than freely substituting one curve. The source has inconsistent unit metadata for the forward curves; do not assume its displayed engineering units without verification.
ip_fac_mff_add_wf_pos[1] and ip_fac_mff_add_wf_neg[1] weight signed film corrections versus rpm and predicted cylinder air mass m_air_cyl_pred in mg/stroke. The positive entry's copied prose calls it negative; check the implementation and sign. ip_fac_mff_add_wf_ast_pos and ip_fac_mff_add_wf_ast_neg are after-start fade factors indexed by tco and cyc_cast; verify the cycle counter definition and reset in the target before interpreting its timing. FMSP wall-film reference.
Runtime signals and testing
mff_add_wf is an additive film compensation value in mg/stroke; mwf_im[3][1] and mwf_cmbc[3][1] are manifold and chamber film-model values. mff_dif_vap_im[3][1] and mff_dif_vap_cmbc[3][1] describe differences between modelled added and vaporised fuel. Their array indices and logging availability must be checked for the target. lv_mwf_ini indicates model initialisation and lv_mff_add_wf_deact a deactivation state in this reference. These are ECU runtime values, not proof of measured fuel film or an editable calibration. FMSP measurements.
First verify injector characterisation, pressure, air charge, lambda sensor and steady-state mixture. Compare repeatable tip-ins and releases at matched rpm and load, cold and warm, recording accelerator and throttle position, RPM, MAP, fuel pressure target and actual, DI/MPI mode if fitted, lambda target and measured lambda, and film/acceleration-enrichment states where exposed. Account for sensor readiness, exhaust transport delay and logger sample rate. A brief lambda deviation alone cannot isolate wall film from air-model, enrichment, injector, fuel-pressure or mechanical faults. Validate both directions and after-start conditions; do not copy numerical factors from an unrelated engine.
Related: acceleration enrichment · MPI modes and fuel split · MPI injector calibration · DI timing · lambda control. References reviewed 17 November 2026.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Simos 18 wall-film fuel compensation
Scope and physical background
Wall-film compensation describes dynamic changes in fuel retained on surfaces and later vaporised. A transient fuel request can therefore differ from the fuel reaching combustion immediately. The intake-manifold film and combustion-chamber film are separate model paths in the SC8S5031_C_OEM FMSP cross-reference; the controller's film masses and correction are estimates, not physical film sensors. A general port-injection wall-wetting model is described by Linköping University, but its equations are background, not proof that Simos implements the same model.
The ECU names below are community-extracted Simos 18.1 examples, not universal calibrations. Match ASW, CAL, A2L, combustion-mode index, units and active branches. Some labels and copied narratives conflict. The presence of an MPI map is not proof that a car has port injectors: Audi SSP 920243 describes both dual-injection and DI-only EA888 Gen3 configurations. Do not assume all 18.x variants or retrofit controllers use these paths identically.
Fuel deposited in the model
ip_fac_mff_wf_hpdi[1][1] describes a factor for distributing high-pressure DI fuel to wall-film models; axes are engine speed n_32 in rpm and basic fuel mass mff_bas in mg/stroke. ip_fac_mff_wf_mpi[1][1] is the corresponding port-injected-fuel factor, indexed by rpm and intake manifold pressure prs_im in hPa. Neither is a DI/MPI overall fuel-split target.
ip_fac_mff_wf_cmbc_temp_cor and ip_fac_mff_wf_im_temp_cor are temperature corrections for fuel added to the chamber and manifold film paths. In this extraction both use tia_im and coolant temperature tco in degrees C. They are model factors, not injector dead-time tables or physical wall-temperature measurements.
id_idx_cal_wf selects film-calibration tables by combustion mode, while idx_cal_wf is the runtime index. Its axis input is labelled NO_INPUT_QUANTITY in the extraction. Confirm indexing and configured modes before deciding which array entry applies. FMSP field descriptions and axes.
Evaporation and correction
ip_fac_mwf_vap_cmbc[1] is an operating-point factor for the chamber film, indexed by rpm and mff_bas; ip_fac_mwf_vap_im[1] is the manifold counterpart, indexed by rpm and prs_im. The chamber entry's copied table prose describes MPI split rather than vaporisation; confirm its actual function against matched source/definition.
ip_fac_mwf_vap_cmbc_temp_cor and ip_fac_mwf_vap_im_temp_cor are temperature-related vaporisation factors with tia_im and tco axes. They are distinct from the temperature factors for fuel deposited in the film.
ip_mff_vap_wf_im[1] and ip_mff_vap_wf_cmbc[1] describe manifold and chamber evaporation behaviour; corresponding ip_mff_vap_wf_im_ivs[1] and ip_mff_vap_wf_cmbc_ivs[1] are inverse curves. Axis inputs are marked NO_INPUT_QUANTITY; confirm scaling, lookup and inverse relationship in the actual software. The reference says the inverse is derived from the forward characteristic, so treat the pair as linked rather than freely substituting one curve. The source has inconsistent unit metadata for the forward curves; do not assume its displayed engineering units without verification.
ip_fac_mff_add_wf_pos[1] and ip_fac_mff_add_wf_neg[1] weight signed film corrections versus rpm and predicted cylinder air mass m_air_cyl_pred in mg/stroke. The positive entry's copied prose calls it negative; check the implementation and sign. ip_fac_mff_add_wf_ast_pos and ip_fac_mff_add_wf_ast_neg are after-start fade factors indexed by tco and cyc_cast; verify the cycle counter definition and reset in the target before interpreting its timing. FMSP wall-film reference.
Runtime signals and testing
mff_add_wf is an additive film compensation value in mg/stroke; mwf_im[3][1] and mwf_cmbc[3][1] are manifold and chamber film-model values. mff_dif_vap_im[3][1] and mff_dif_vap_cmbc[3][1] describe differences between modelled added and vaporised fuel. Their array indices and logging availability must be checked for the target. lv_mwf_ini indicates model initialisation and lv_mff_add_wf_deact a deactivation state in this reference. These are ECU runtime values, not proof of measured fuel film or an editable calibration. FMSP measurements.
First verify injector characterisation, pressure, air charge, lambda sensor and steady-state mixture. Compare repeatable tip-ins and releases at matched rpm and load, cold and warm, recording accelerator and throttle position, RPM, MAP, fuel pressure target and actual, DI/MPI mode if fitted, lambda target and measured lambda, and film/acceleration-enrichment states where exposed. Account for sensor readiness, exhaust transport delay and logger sample rate. A brief lambda deviation alone cannot isolate wall film from air-model, enrichment, injector, fuel-pressure or mechanical faults. Validate both directions and after-start conditions; do not copy numerical factors from an unrelated engine.
Related: acceleration enrichment · MPI modes and fuel split · MPI injector calibration · DI timing · lambda control. References reviewed 17 November 2026.
Revision 1: Simos 18 wall-film fuel compensation
Scope and physical background
Wall-film compensation describes dynamic changes in fuel retained on surfaces and later vaporised. A transient fuel request can therefore differ from the fuel reaching combustion immediately. The intake-manifold film and combustion-chamber film are separate model paths in the SC8S5031_C_OEM FMSP cross-reference; the controller's film masses and correction are estimates, not physical film sensors. A general port-injection wall-wetting model is described by Linköping University, but its equations are background, not proof that Simos implements the same model.
The ECU names below are community-extracted Simos 18.1 examples, not universal calibrations. Match ASW, CAL, A2L, combustion-mode index, units and active branches. Some labels and copied narratives conflict. The presence of an MPI map is not proof that a car has port injectors: Audi SSP 920243 describes both dual-injection and DI-only EA888 Gen3 configurations. Do not assume all 18.x variants or retrofit controllers use these paths identically.
Fuel deposited in the model
ip_fac_mff_wf_hpdi[1][1] describes a factor for distributing high-pressure DI fuel to wall-film models; axes are engine speed n_32 in rpm and basic fuel mass mff_bas in mg/stroke. ip_fac_mff_wf_mpi[1][1] is the corresponding port-injected-fuel factor, indexed by rpm and intake manifold pressure prs_im in hPa. Neither is a DI/MPI overall fuel-split target.
ip_fac_mff_wf_cmbc_temp_cor and ip_fac_mff_wf_im_temp_cor are temperature corrections for fuel added to the chamber and manifold film paths. In this extraction both use tia_im and coolant temperature tco in degrees C. They are model factors, not injector dead-time tables or physical wall-temperature measurements.
id_idx_cal_wf selects film-calibration tables by combustion mode, while idx_cal_wf is the runtime index. Its axis input is labelled NO_INPUT_QUANTITY in the extraction. Confirm indexing and configured modes before deciding which array entry applies. FMSP field descriptions and axes.
Evaporation and correction
ip_fac_mwf_vap_cmbc[1] is an operating-point factor for the chamber film, indexed by rpm and mff_bas; ip_fac_mwf_vap_im[1] is the manifold counterpart, indexed by rpm and prs_im. The chamber entry's copied table prose describes MPI split rather than vaporisation; confirm its actual function against matched source/definition.
ip_fac_mwf_vap_cmbc_temp_cor and ip_fac_mwf_vap_im_temp_cor are temperature-related vaporisation factors with tia_im and tco axes. They are distinct from the temperature factors for fuel deposited in the film.
ip_mff_vap_wf_im[1] and ip_mff_vap_wf_cmbc[1] describe manifold and chamber evaporation behaviour; corresponding ip_mff_vap_wf_im_ivs[1] and ip_mff_vap_wf_cmbc_ivs[1] are inverse curves. Axis inputs are marked NO_INPUT_QUANTITY; confirm scaling, lookup and inverse relationship in the actual software. The reference says the inverse is derived from the forward characteristic, so treat the pair as linked rather than freely substituting one curve. The source has inconsistent unit metadata for the forward curves; do not assume its displayed engineering units without verification.
ip_fac_mff_add_wf_pos[1] and ip_fac_mff_add_wf_neg[1] weight signed film corrections versus rpm and predicted cylinder air mass m_air_cyl_pred in mg/stroke. The positive entry's copied prose calls it negative; check the implementation and sign. ip_fac_mff_add_wf_ast_pos and ip_fac_mff_add_wf_ast_neg are after-start fade factors indexed by tco and cyc_cast; verify the cycle counter definition and reset in the target before interpreting its timing. FMSP wall-film reference.
Runtime signals and testing
mff_add_wf is an additive film compensation value in mg/stroke; mwf_im[3][1] and mwf_cmbc[3][1] are manifold and chamber film-model values. mff_dif_vap_im[3][1] and mff_dif_vap_cmbc[3][1] describe differences between modelled added and vaporised fuel. Their array indices and logging availability must be checked for the target. lv_mwf_ini indicates model initialisation and lv_mff_add_wf_deact a deactivation state in this reference. These are ECU runtime values, not proof of measured fuel film or an editable calibration. FMSP measurements.
First verify injector characterisation, pressure, air charge, lambda sensor and steady-state mixture. Compare repeatable tip-ins and releases at matched rpm and load, cold and warm, recording accelerator and throttle position, RPM, MAP, fuel pressure target and actual, DI/MPI mode if fitted, lambda target and measured lambda, and film/acceleration-enrichment states where exposed. Account for sensor readiness, exhaust transport delay and logger sample rate. A brief lambda deviation alone cannot isolate wall film from air-model, enrichment, injector, fuel-pressure or mechanical faults. Validate both directions and after-start conditions; do not copy numerical factors from an unrelated engine.
Related: acceleration enrichment · MPI modes and fuel split · MPI injector calibration · DI timing · lambda control. References reviewed 17 November 2026.