Simos 8.3 is a Continental/Siemens engine-management variant listed by programming-tool suppliers for selected Volkswagen Group 3.0 TFSI applications. Audi's factory documentation describes the related CAJA 3.0 TFSI with Simos 8, but does not establish the 8.3 suffix for every CAJA vehicle. Match the ECU and software before choosing a definition or programming protocol.
Applications and identification
Flashtec's 2013 CMDFlash revision history names an Audi A6 3.0 TFSI with identifier 4F1910551 and a Q7 3.0 TFSI with identifier 4L0910551 as Simos 8.3 examples. A 2018 Dimsport newsletter lists selected A6, Q7 and Touareg 3.0 V6 TFSI examples as Simos 8.3 for its protocol. These are historical product coverage statements, not complete vehicle fitment lists.
Some sources describe Simos 8.31 separately while others use the broader 8.3 designation. Record the label, full hardware and software numbers, calibration identifier, engine code, model and gearbox. Confirm what the selected tool means by each designation rather than assuming 8.3, 8.31 or 8.4 files are interchangeable.
Catalogue descriptions can conflict. For example, a file catalogue describes one CAJA entry as 3.2 litres, whereas Audi's SSP 437 specifies the CAJA as a 2,995 cm³ 3.0 TFSI. Treat commercial vehicle labels as leads, not proof of the engine or ECU installed.
CAJA air and load control
Audi's SSP 437 describes a mechanically driven Roots supercharger, a bypass control unit and integrated charge-air coolers on the CAJA engine. It names the ECU family Simos 8, without a more specific suffix. In the documented system the bypass recirculates air from the pressure side to the inlet; its control flap regulates charge pressure in charging operation. At part load the bypass and throttle operate differently from that charging condition. The blower is permanently belt-driven in this training example; do not assume it has the clutch used by some later engines.
Audi identifies the G31 and G447 charge-pressure senders for its two banks and the bypass control flap unit J808 with position feedback. These details belong to the SSP 437 engine configuration, not a promise that every Simos 8.3 application has identical hardware. See charge-air and bypass log review for related diagnostic concepts, checking the fitted engine before transferring a procedure.
Calibration and logs
One seller's 4F1910551 0050 map-pack listing advertises labels including torque request, requested lambda, ignition, air quantity and rail pressure. Those are vendor labels for one advertised file, not independently established function names, axes, addresses or safe changes. In particular, its “turbo pressure” label should not be taken as evidence that Audi's CAJA uses an exhaust-driven turbocharger. Validate definitions against the actual software and hardware.
Establish a healthy baseline and, where supported, compare requested and actual charge pressure, bypass position and command, throttle, lambda, fuel pressure, knock corrections and charge-air temperature under repeatable conditions. Confirm pressure units and absolute versus gauge readings. Check cooling, air leaks, bypass operation and fuel delivery before drawing conclusions from a pressure or torque mismatch; requested and ECU-estimated values are not the same as measured output.
Reading and writing
Flashtec's 2013 revision history advertises CAN read, write, checksum and recovery for its named 8.3 examples. Dimsport's 2018 newsletter describes an OBD writing mode for certain 8.3/8.4 applications with a matching certified original file, and a separate older unlock workflow. These are product- and version-specific statements: a listing for OBD does not establish the file scope, prerequisites or recovery support for another unit or tool. Confirm current exact coverage, checksum handling, stable supply, original-file provenance and recovery arrangements before writing. A supplied original or calibration read is not automatically a complete physical backup of the ECU.
The PCMflash module 57 manual, page 49, separately lists virtual reading, writing and checksum functions for its Simos 8.3 application entry. This describes that product's scope, not independent confirmation that a virtual file is the data currently stored in the vehicle. Check the complete ECU and software identity, current tool coverage and required file format.
Sources
- Audi SSP 437: 3.0-litre V6 TFSI engine with Roots blower. CAJA specification, Simos 8 family, charge, bypass and sensor operation; no ECU suffix stated. Accessed 17 November 2026.
- Flashtec CMDFlash 2013 software revisions, 18 January and 1 February. Historical A6/Q7 Simos 8.3 identifiers and product coverage. Accessed 17 November 2026.
- Dimsport RACE newsletter, 10 July 2018, third-party host. Selected 8.3 applications and protocol requirements. Accessed 17 November 2026.
- Microtronik HexProg: Audi Simos 8.31. Vendor-specific identification and access coverage. Accessed 17 November 2026.
- Auto-Remap 4F1910551 0050 map-pack listing. Seller's file-specific labels and file-scope statement. Accessed 17 November 2026.
- Auto-Remap Simos 8.3 file catalogue. Conflicting CAJA displacement example. Accessed 17 November 2026.