Speeduino and MegaSquirt installations can use TunerStudio for configuration and tuning, but they are different ECU and firmware families. SpeedyLoader installs Speeduino firmware; MegaLogViewer examines recorded data. Match the software project, ECU firmware, definition file and tune to the hardware in use. See also Speeduino hardware and MegaSquirt and MicroSquirt identification.
Which program does what?
- TunerStudio MS: connects to a supported ECU, displays live data, edits the configuration and tune, and records logs. The software reads a firmware-specific definition, often called an INI file, which describes the ECU settings and data. EFI Analytics provides a free edition and paid editions; features and licensing vary by edition. VE Analyze Live is a paid feature according to its product description. TunerStudio product and download.
- SpeedyLoader: the Speeduino project’s cross-platform loader selects and installs precompiled Speeduino firmware without requiring the user to compile source. The Speeduino manual says it also downloads the corresponding INI and can offer a base tune. It is for Speeduino devices, not a general MegaSquirt firmware updater. Speeduino firmware installation; SpeedyLoader project.
- MegaLogViewer: opens recorded logs for graphing and analysis after a run. Some editions provide additional analysis features. It does not replace the ECU firmware or hardware setup; use logs with the matching tune and understand the sensor data before acting on suggestions. DIYAutoTune software downloads; EFI Analytics VE analysis guide.
- MegaSquirt firmware utilities: the MSExtra downloads page provides separate firmware families. DIYAutoTune describes a TunerStudio firmware-loading utility for MS2 and MS3 products, but not discontinued MS1. Follow the specific product guide and release instructions.
Set up a Speeduino TunerStudio project
- Identify the exact board, processor, firmware and communication interface. Download software and firmware from the project or board supplier, and read the release notes. Installation instructions vary with the processor and board; a third-party PNP board may have supplier-specific requirements.
- For a new or intentionally updated ECU, use the Speeduino firmware guide and choose the correct firmware and processor in SpeedyLoader. Obtain the corresponding INI and a compatible base tune. Save the existing tune first when updating an ECU, and follow any migration instructions in the firmware release.
- Create a TunerStudio project and use the correct INI for the firmware actually installed. Connect via the ECU's supported serial/USB interface and select the appropriate port. A USB adapter may need its correct driver or operating-system serial-port permissions. If the ECU is not detected, verify power, cabling, port, driver and firmware/INI pairing; do not assume a failed ECU from one connection attempt.
- Load a compatible base tune where required by the Speeduino manual. A base tune is a starting point, not proof that a particular engine or wiring is correctly configured. Review engine, injector, trigger, ignition, sensor and output settings against the actual installation before attempting a start.
- In project properties choose the correct controller and display units; display choices do not necessarily alter underlying calibration. The Speeduino manual states that hardware output tests should only be enabled when the ECU is not connected to a vehicle. See Speeduino project properties.
MegaSquirt setup
Identify the product, processor, mainboard, firmware family and version. Use the matching MSExtra manual, or the correct B&G documentation for a unit using that firmware. The TunerStudio setup guide shows project creation and ECU detection for MegaSquirt. Retain an unmodified copy of the existing tune and note the old firmware version before an update. The MS2/MS3 firmware update guide describes the procedure and precautions; it does not apply to MS1.
Working with tunes and logs
- Save the current tune and record the engine configuration, ECU identity, firmware, sensor calibration and date. Keep a known working tune available before making changes.
- Confirm sensor readings and the crank/cam trigger signal. Where the system controls ignition, verify commanded timing against actual timing with the proper timing light and procedure for that engine and ECU before tuning the spark table. See the MegaSquirt startup guide.
- Record logs during repeatable, controlled conditions. Review RPM, load, coolant temperature, throttle position, target and measured lambda/AFR, battery voltage and relevant status indicators. A calibrated wideband and correctly configured controller are needed for meaningful wideband readings.
- Review data in MegaLogViewer with the tune and firmware that produced it. Check sample quality and sensor delay when using analysis functions. Suggested fuel-table changes are aids for review, not validation of ignition timing or mechanical condition.
- Establish steady-state fuelling before refining transient acceleration enrichment, and revisit cold-start and warm-up behaviour under appropriate conditions. See DIYAutoTune acceleration enrichment and the Speeduino tuning manual.