MegaSquirt is a family of configurable aftermarket engine management systems. MegaSquirt, MicroSquirt and MS3Pro are related product families; Speeduino is a separate project, even though both use TunerStudio in supported configurations. Shared tuning software does not make their firmware, wiring or tunes interchangeable.
Identify the ECU before making changes
- Record the complete product name, label, case and connector, and whether it is a universal wire-in or a vehicle-specific plug-in unit. Consult the MegaSquirt identification guide.
- For traditional MegaSquirt units identify both the processor generation (MS1, MS2 or MS3) and mainboard revision (such as V2.2, V3.0 or V3.57). An ECU case alone may not establish its processor or its internal customisation. Identify an MS3X expansion card if fitted.
- Connect with the appropriate tuning application and record the ECU firmware family and version; identify B&G versus Extra firmware for MS1/MS2. Save the existing tune before changing configuration or firmware. Record any custom jumper settings and modifications.
- Use the correct manual for the processor, board, firmware and actual product. For plug-in products also check vehicle, engine, model year, transmission and product part number against the manufacturer's application instructions.
Families and useful differences
- MegaSquirt-I (MS1): the original generation; now obsolete. Capabilities depend on board, firmware and modifications. MS1/Extra and the original B&G firmware have different documentation. The MS1 firmware loader differs from the MS2/MS3 updater.
- MegaSquirt-II (MS2): a later processor family used with traditional boards. MS2/Extra supports a broad range of engine-management functions; injector and ignition arrangements depend on the actual hardware and installation. The official setup manual describes additional DIY hardware as necessary for more MS2 injector outputs.
- MicroSquirt V3: a compact, assembled MS2-technology ECU. The manufacturer's product guide describes two saturated injector drivers and a batch-fire or semi-sequential focus. It lists logic-level ignition outputs, but two additional channels require a harness modification; check the exact model and documentation. It can also run dedicated transmission-control or I/O-expansion firmware for a supported application: these are separate firmware uses, not an automatic assumption of simultaneous engine and transmission control.
- MicroSquirt V2 and MicroSquirt Module V2.2: earlier or embedded variants. Treat the embedded module and the complete ECU as different hardware, and check the specific revision and host board.
- MegaSquirt-III (MS3): a later family available in traditional mainboard form. The optional MS3X expander provides additional inputs and outputs. The manufacturer's traditional range describes MS3X support for eight sequential fuel channels and logic ignition outputs on the specified hardware; coil drivers, injector type and actual configuration still require verification.
- MS3Pro Gen1, EVO, EVO Plus, EVO Plus HC, Mini and Ultimate: product-specific MS3Pro variants. Do not assume their pinouts, drivers or I/O counts are identical. The product manuals identify the correct hardware.
- MSPNP2 and MS3Pro PNP: vehicle-specific plug-in products. PNP describes the installation format, not universal interchangeability; match each part number and application.
Board versions and fuel/ignition outputs
The manufacturer's comparison describes MS1 and MS2 with V2.2, V3.0 or V3.57 mainboards and MS3 with V3.0 or V3.57. V3.0 is a DIY-oriented through-hole board; V3.57 is preassembled. V2.2 is an older design. The comparison is an archive and its feature table refers to specific historic firmware, so check current product and firmware manuals before selecting a system. Sequential injection requires adequate separately controlled injector outputs, suitable crank/cam synchronisation and a correct configuration; a family name alone does not establish this. Logic-level ignition outputs must be matched to suitable coils or external drivers.
Manual and firmware selection
Use the MSExtra manual index for MS1/Extra, MS2/Extra, MicroSquirt, MS3 and product-specific MS3Pro manuals. The index states that the original MegaManual is for alternative B&G MS1/MS2 firmware; its instructions may be misleading for Extra firmware. The official downloads separate MS1, MS2, MS3 and dedicated MicroSquirt transmission/I/O releases. Never select firmware merely because a connector fits.