Dynamometer testing combines rotating machinery, a restrained vehicle or engine, heat, noise and exhaust gases. A test setup must suit the particular dynamometer, vehicle and test cell; the machine manufacturer’s instructions, a competent operator and the site risk assessment take precedence over a generic checklist. See the dynamometers overview and measurement and interpreting results.
Before the vehicle is run
- Check compatibility and capacity. Confirm vehicle mass, driven axles, wheelbase, tyre speed rating, power, torque and expected speed are within the dyno, restraint and test-cell limits. An AWD vehicle may require linked rollers or a specific test procedure. Verify the manufacturer’s instructions for the vehicle’s transmission, differential, stability and hybrid systems; do not assume a two-wheel-drive test is safe.
- Inspect the machine and vehicle. Check guards, emergency stop, brake, extraction and cooling, and look for leaks, loose parts, damaged tyres and unsafe mechanical condition. Check fluid levels, tyre condition and pressure; remove debris from tread. Arrange leads and hoses away from heat and moving parts. The Dynojet Model 224 installation and operation guide gives a model-specific pre-run inspection.
- Position and restrain. Align driven wheels as directed, use rated restraints and designated anchorage points in the arrangement specified for the machine and vehicle, and check tension. Protect straps from abrasion and hot or rotating parts. Chock only where the specific manufacturer’s instructions call for it. Hub and engine installations need correctly rated, properly fitted adapters, fasteners, couplings and supports rather than tyre straps alone.
- Prepare the room. Connect suitable exhaust extraction before starting and discharge it to a safe outdoor position; provide adequate replacement air and separate cooling airflow. HSE warns that exhaust fumes can rapidly reach harmful concentrations and that open doors alone are not a reliable control. See HSE vehicle exhaust emissions and HSE SR14 guidance. A cooling fan aimed at the radiator or intercooler is not a substitute for exhaust extraction.
People and operating area
Limit access, communicate the test and stop procedure, and position people outside the machine’s danger zones. The Dynojet Model 224 guide says only the operator should be near the vehicle during operation and nobody should stand behind it. Keep hands, clothing, cables and tools clear of rollers, tyres, shafts, couplings and fan blades. Fit guards and use appropriate hearing and eye protection. Verify the emergency stop and operator’s safe access before the run. The site’s risk assessment should cover fire, fuel, hot surfaces, ejected objects, noise, electrical hazards and the stored energy in a spinning roller. Dynojet Model 224 guide; Dynojet safety warnings.
During and after a test
Begin with a controlled low-load check for alignment, movement, vibration, smoke, leaks, abnormal noise and believable speed signals. Stop the test if anything is abnormal, if restraint or extraction fails, or if operating limits are approached. Keep cooling and extraction effective through the test and cooldown. Do not approach or adjust moving parts while they coast down; wait until rotation has stopped and isolate equipment as required before servicing or removing guards. Follow the manufacturer’s shutdown and unloading sequence.
Engine and hub installations
An engine cell needs suitable mounts, a guarded coupling, services for fuel, cooling and exhaust, and controls for both the engine and absorber. Torque reactions and vibration must be carried by the designed supports. Hub dynos remove tyre slip but still require secure adapters, correct fasteners and restraint, with the vehicle supported according to the equipment maker’s procedure. Neither layout removes the need for an exclusion zone, emergency shutdown, extraction or cooling.
Recording a repeatable setup
Once safe, record the dyno and vehicle configuration, restraint and tyre setup, fuel, test gear, test mode, sweep rate, cooling and temperatures, and the correction method. Use consistent warm-up and cooldown, and investigate wheel slip or changes in boost, temperature or electronic intervention before attributing a curve change to a modification. Manufacturer-specific procedures and the site’s safety arrangements determine the details. See SuperFlow: dynamometer testing oversights.
Plan the test around the actual machine
Before a vehicle arrives, identify the driven axles, differential or transfer-case arrangements, electric drives, wheelbase, mass and expected hub or roller torque and speed. Compare the planned test with the equipment's continuous and short-duration operating envelopes, roller and tyre speed ratings, hub-adapter limits, restraint and anchorage ratings, ventilation and brake cooling. A peak horsepower label alone does not establish a safe or controllable operating point. Record any required vehicle-specific test mode and whether it is permitted by the vehicle manufacturer.
Decide who operates the test, who can enter the test area, where the stop controls are and how the run will be stopped. Inspect attachments and the vehicle before each test and follow a documented setup suitable for that machine. HSE's motor vehicle repair guidance discusses high-speed rolling-road equipment and keeping the test area controlled.
Rolling-road restraint and roller checks
- Centre the driven wheels as directed by the dyno maker and check tyres for visible damage, foreign objects and suitability for the intended speed. The relevant tyre and roller limits, not the speed display alone, govern the test.
- Use only the specified, rated anchorages, restraints and vehicle attachment points. Inspect webbing, hooks and attachment hardware for damage; route straps away from hot exhaust, sharp edges, wheels and shafts. Do not copy a strap angle or loading arrangement from a photograph of a different installation.
- Verify permitted access and guarding around rollers and rotating tyres; keep the area behind the vehicle and other machine-specific danger zones clear as required. Avoid placing hands, tools, test leads or loose clothing near moving parts. Follow the dyno maker's loading, brake and shutdown sequence.
- AWD, electronically controlled differentials and stability systems can respond to mismatched wheel speeds. Follow the vehicle and dyno manufacturer's test instructions and use an appropriate linked or controlled-axle arrangement. Electronic synchronisation alone is not proof that every vehicle can be run safely.
Different equipment may specify different restraint methods. For example, Dynojet's 250iP motorcycle instructions show a particular motorcycle setup; they are not a generic passenger-car restraint procedure.
Hub and engine-cell setup
For a hub dyno, verify adapters, wheel-stud engagement and fasteners against the equipment and vehicle manufacturer's instructions. Support and restrain the vehicle and units in the designed configuration, respecting permitted hub and axle loads and driveline angles. Confirm whether the equipment requires two or four units and how the axles are controlled. Guard moving couplings and route cables and cooling hoses out of moving or hot areas.
For an engine test cell, use the specified rated engine mounts, coupling, guards and test-bed reaction supports. Fuel, coolant, exhaust and electrical services must be installed for the test cell and checked for leaks, interference and heat. Use the manufacturer’s actuator and control procedures. An engine test stand and a hub or rolling-road installation share some hazards, but their restraints and rotating interfaces are not interchangeable.
Exhaust, cooling, noise and fire
Connect and use the exhaust extraction system appropriate to the engine, fuel, test and facility. Confirm that connections remain in position during the full operating range and that discharge does not re-enter the workplace or affect others. Radiator and charge-cooler fans are separate from exhaust extraction. HSE warns that indoor exhaust can rapidly reach hazardous concentrations and that open doors or the vehicle's catalytic converter are not reliable substitutes for exhaust extraction. HSE: vehicle exhaust emissions.
Provide the specified cooling to the vehicle, test-cell air and absorber. A water brake, water-cooled eddy brake, hydraulic oil cooler or electric drive can each have different flow, temperature and ventilation requirements. Consult the equipment maker for monitoring and shutdown thresholds rather than using a generic value. Assess noise, fire, fuel and hot-surface hazards, and provide the facility's appropriate protective equipment and emergency arrangements.
Electric and hybrid vehicles
Electric and hybrid vehicles can move without engine noise and can start or change operating state automatically. A vehicle under test can contain hazardous high-voltage equipment and stored electrical energy. Do not open high-voltage components or disturb orange cables as part of a routine dyno setup; any high-voltage work needs the vehicle-specific procedure and suitably trained personnel. Use appropriate key control and confirm the manufacturer's test-mode and emergency procedures for the actual vehicle.
Turning drive wheels can generate voltage on some vehicles, and an electric motor/generator dyno can actively drive the vehicle when configured to do so. Treat a stopped engine or silent vehicle as insufficient evidence that the driveline is safe to touch. HSE's electric and hybrid vehicle guidance describes these hazards and the need for vehicle-specific information.
Run, stop and handover
- Before loading, confirm the operator's controls and displays, limits, interlocks, exhaust extraction, cooling and emergency procedure. Start with the manufacturer's low-load checks and verify expected speed and load readings.
- During a run, watch for movement, vibration, unusual noise, leaks, overheating and fault indications. Stop or abort according to the equipment's procedure if a fault appears or limits are approached; do not attempt to correct a physical problem near rotating parts.
- After the run, follow the prescribed shutdown and cooldown sequence. Wait for all rollers, shafts and fans that pose a hazard to stop; isolate and secure energy sources as required before inspection, unstrapping or removing guards.
- Record relevant test conditions and any defect, and ensure the vehicle and equipment are safe for the next operator. Follow the facility's fault-reporting and maintenance procedures before further use.
This is a planning checklist, not a substitute for manufacturer instructions, competent operators, local safety requirements or the site's risk assessment. See measurement and interpreting results for documenting a repeatable test.
See dynamometer calibration and verification for safe, traceable checks of the measuring system.