PnPduino Universal8 is a PnPduino programmable engine-management ECU. Manufacturer product information.

Application and identification
An upgraded configurable wire-in ECU that the manufacturer describes for up to eight cylinders with sequential injection and ignition. It can be used as standalone or piggyback; the listing specifies manual transmission and cable-throttle operation.
System and wiring
Separate 34-position AMP Superseal 1.0 connectors are used for inputs and outputs, with three-slot and four-slot housings respectively. The STM32-MEGA processor provides CAN and onboard microSD logging according to the listing. Internal MAP, Bluetooth, VR conditioner, stepper driver and wideband are optional. The ASA/ABS case is not waterproof and is intended for installation inside the car.
Connector identification
| Connector | Manufacturer description | Scope |
|---|---|---|
| Input header | 34 positions, AMP Superseal 1.0, three-slot | Manufacturer product listing |
| Output header | 34 positions, AMP Superseal 1.0, four-slot | Manufacturer product listing |
The manufacturer’s model-specific connector schedule is transcribed below. Confirm the hardware revision, optional equipment and calibration before wiring.
Software and calibration
The product lists TunerStudio and official Speeduino firmware. Verify outputs, sensors and firmware for the actual build and obtain the model-specific pinout before wiring.
See the PnPduino manufacturer index.
Model-specific wiring document
The manufacturer provides the revision 2 Universal8 two-connector drawing; verify the hardware revision and actual build before using its assignments. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the full manufacturer-labelled schedule follows below.
PnPduino Universal8 manufacturer connector schedule
Transcribed from the PnPduino PnPduino Universal8 pinout revision 2. Follow the connector drawing in the source and verify the actual build and orientation; the source does not explicitly identify its view as ECU-face or wire-side. Arduino pins are software/board assignments, not connector cavity numbers. A blank manufacturer label is recorded as unlabelled rather than assumed unused.
A-plug input — 34 positions
| ECU pin | Manufacturer label | Manufacturer description | Arduino pin |
|---|---|---|---|
| A1 | INP4 | Spare Input 4 | A11 |
| A2 | INP1 | Spare Input 1 | A8 |
| A3 | CLT | Engine Coolant Temp | A4 |
| A4 | O2 | Wideband O2 Sensor | A1 |
| A5 | CANH | CAN Hi | STM32 |
| A6 | VR2+ | VR2+ or Hall Sensor 2 | D18 |
| A7 | VR1+ | VR1+ or Hall Sensor 1 | D19 |
| A8 | 5V Out | 5V Out to sensors | — |
| A9 | 12V In | 12V Input from Ignition switch | — |
| A10 | INP3 | Spare Input 3 | A10 |
| A11 | IAT | Intake Air Temperature | A5 |
| A12 | TPS | Throttle Position Sensor | A3 |
| A13 | CLUTCH | Clutch Switch | 37 |
| A14 | CANL | CAN Lo | STM32 |
| A15 | VR2- | VR2- or Hall Sensor 2 Logic Ground | — |
| A16 | VR1- | VR1- or Hall Sensor 1 Logic Ground | — |
| A17 | INP5 | Spare Input 5 | A6 |
| A18 | INP9 | Spare Input 9 | A15 |
| A19 | INP2 | Spare Input 2 | A9 |
| A20 | 12V Out | Fused 12V Supply to sensors only | — |
| A21 | 12V Out | Fused 12V Supply to sensors only | — |
| A22 | 12V Out | Fused 12V Supply to sensors only | — |
| A23 | 12V Out | Fused 12V Supply to sensors only | — |
| A24 | Not labelled in source | Not labelled in source | — |
| A25 | INP7 | Spare Input 7 | A13 |
| A26 | EXTMAP | External MAP sensor | A0 |
| A27 | INP8 | Spare Input 8 | A14 |
| A28 | FLEX | Flex Fuel Sensor | 2 |
| A29 | HALL4 | Hall Sensor 4 | 3 |
| A30 | GRND | ECU Logic Ground | — |
| A31 | GRND | Power Ground | — |
| A32 | GRND | Sensor Ground | — |
| A33 | Not labelled in source | Not labelled in source | — |
| A34 | INP6 | Spare Input 6 | A12 |
B-plug output — 34 positions
| ECU pin | Manufacturer label | Manufacturer description | Arduino pin |
|---|---|---|---|
| B1 | VVT | VVT/VVTI or VTEC/VTC terminology | 11 |
| B2 | IDLE2 | Idle 2 or Spare High Current 1 | 10 |
| B3 | IDLE1 | Idle 1 for IACV Solenoid | 9 |
| B4 | INJ4 | Injector 4 | 5 |
| B5 | INJ3 | Injector 3 | 6 |
| B6 | INJ2 | Injector 2 | 7 |
| B7 | INJ1 | Injector 1 | 8 |
| B8 | INJ8 | Injector 8 | 49 |
| B9 | INJ7 | Injector 7 | 47 |
| B10 | BOOST | Boost or Spare Hi Current 2 | 12 |
| B11 | LC4 | Low Current Output 4 | 29 |
| B12 | LC3 | Low Current Output 3 | 28 |
| B13 | LC1 | Low Current Output 1 | 26 |
| B14 | FAN | Radiator Fan 1 | 24 |
| B15 | TACH | Tachometer Output 5V or 12V | 22 |
| B16 | FUELP | Fuel Pump or Circuit Opening Relay | 23 |
| B17 | INJ6 | Injector 6 | 45 |
| B18 | IGN4 | Ignition Output 4 | 34 |
| B19 | IGN3 | Ignition Output 3 | 33 |
| B20 | STP-B2 | Stepper Idle Air Coil B2 | — |
| B21 | STP-A2 | Stepper Idle Air Coil A2 | — |
| B22 | FAN2 | Radiator Fan 2 | 25 |
| B23 | GRND | Power Ground | — |
| B24 | GRND | Power Ground | — |
| B25 | INJ5 | Injector 5 | 42 |
| B26 | IGN1 | Ignition Output 1 | 35 |
| B27 | IGN2 | Ignition Output 2 | 36 |
| B28 | STP-B1 | Stepper Idle Air Coil B1 | — |
| B29 | STP-A1 | Stepper Idle Air Coil A1 | — |
| B30 | LC2 | Low Current Output 2 | 27 |
| B31 | IGN8 | Ignition Output 8 | 41 |
| B32 | IGN7 | Ignition Output 7 | 40 |
| B33 | IGN6 | Ignition Output 6 | 39 |
| B34 | IGN5 | Ignition Output 5 | 38 |
The revision-2 source states that IDLE2 and BOOST can be used as high-current outputs and that a PWM radiator fan should use FAN2. It says vehicle speed can be wired to Hall 3, but does not assign Hall 3 a cavity in this table; A24 and A33 are blank and are not assumed to be Hall 3. Follow the manufacturer’s grounding instructions.