Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

PnPduino Universal8 is a PnPduino programmable engine-management ECU. Manufacturer product information.

PnPduino Universal8
PnPduino Universal8. PnPduino manufacturer product photograph, reproduced with permission.

Application and identification

An upgraded configurable wire-in ECU that the manufacturer describes for up to eight cylinders with sequential injection and ignition. It can be used as standalone or piggyback; the listing specifies manual transmission and cable-throttle operation.

System and wiring

Separate 34-position AMP Superseal 1.0 connectors are used for inputs and outputs, with three-slot and four-slot housings respectively. The STM32-MEGA processor provides CAN and onboard microSD logging according to the listing. Internal MAP, Bluetooth, VR conditioner, stepper driver and wideband are optional. The ASA/ABS case is not waterproof and is intended for installation inside the car.

Connector identification

ConnectorManufacturer descriptionScope
Input header34 positions, AMP Superseal 1.0, three-slotManufacturer product listing
Output header34 positions, AMP Superseal 1.0, four-slotManufacturer product listing

The manufacturer’s model-specific connector schedule is transcribed below. Confirm the hardware revision, optional equipment and calibration before wiring.

Software and calibration

The product lists TunerStudio and official Speeduino firmware. Verify outputs, sensors and firmware for the actual build and obtain the model-specific pinout before wiring.

See the PnPduino manufacturer index.

Model-specific wiring document

The manufacturer provides the revision 2 Universal8 two-connector drawing; verify the hardware revision and actual build before using its assignments. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the full manufacturer-labelled schedule follows below.

PnPduino Universal8 manufacturer connector schedule

Transcribed from the PnPduino PnPduino Universal8 pinout revision 2. Follow the connector drawing in the source and verify the actual build and orientation; the source does not explicitly identify its view as ECU-face or wire-side. Arduino pins are software/board assignments, not connector cavity numbers. A blank manufacturer label is recorded as unlabelled rather than assumed unused.

A-plug input — 34 positions

ECU pinManufacturer labelManufacturer descriptionArduino pin
A1INP4Spare Input 4A11
A2INP1Spare Input 1A8
A3CLTEngine Coolant TempA4
A4O2Wideband O2 SensorA1
A5CANHCAN HiSTM32
A6VR2+VR2+ or Hall Sensor 2D18
A7VR1+VR1+ or Hall Sensor 1D19
A85V Out5V Out to sensors—
A912V In12V Input from Ignition switch—
A10INP3Spare Input 3A10
A11IATIntake Air TemperatureA5
A12TPSThrottle Position SensorA3
A13CLUTCHClutch Switch37
A14CANLCAN LoSTM32
A15VR2-VR2- or Hall Sensor 2 Logic Ground—
A16VR1-VR1- or Hall Sensor 1 Logic Ground—
A17INP5Spare Input 5A6
A18INP9Spare Input 9A15
A19INP2Spare Input 2A9
A2012V OutFused 12V Supply to sensors only—
A2112V OutFused 12V Supply to sensors only—
A2212V OutFused 12V Supply to sensors only—
A2312V OutFused 12V Supply to sensors only—
A24Not labelled in sourceNot labelled in source—
A25INP7Spare Input 7A13
A26EXTMAPExternal MAP sensorA0
A27INP8Spare Input 8A14
A28FLEXFlex Fuel Sensor2
A29HALL4Hall Sensor 43
A30GRNDECU Logic Ground—
A31GRNDPower Ground—
A32GRNDSensor Ground—
A33Not labelled in sourceNot labelled in source—
A34INP6Spare Input 6A12

B-plug output — 34 positions

ECU pinManufacturer labelManufacturer descriptionArduino pin
B1VVTVVT/VVTI or VTEC/VTC terminology11
B2IDLE2Idle 2 or Spare High Current 110
B3IDLE1Idle 1 for IACV Solenoid9
B4INJ4Injector 45
B5INJ3Injector 36
B6INJ2Injector 27
B7INJ1Injector 18
B8INJ8Injector 849
B9INJ7Injector 747
B10BOOSTBoost or Spare Hi Current 212
B11LC4Low Current Output 429
B12LC3Low Current Output 328
B13LC1Low Current Output 126
B14FANRadiator Fan 124
B15TACHTachometer Output 5V or 12V22
B16FUELPFuel Pump or Circuit Opening Relay23
B17INJ6Injector 645
B18IGN4Ignition Output 434
B19IGN3Ignition Output 333
B20STP-B2Stepper Idle Air Coil B2—
B21STP-A2Stepper Idle Air Coil A2—
B22FAN2Radiator Fan 225
B23GRNDPower Ground—
B24GRNDPower Ground—
B25INJ5Injector 542
B26IGN1Ignition Output 135
B27IGN2Ignition Output 236
B28STP-B1Stepper Idle Air Coil B1—
B29STP-A1Stepper Idle Air Coil A1—
B30LC2Low Current Output 227
B31IGN8Ignition Output 841
B32IGN7Ignition Output 740
B33IGN6Ignition Output 639
B34IGN5Ignition Output 538

The revision-2 source states that IDLE2 and BOOST can be used as high-current outputs and that a PWM radiator fan should use FAN2. It says vehicle speed can be wired to Hall 3, but does not assign Hall 3 a cavity in this table; A24 and A33 are blank and are not assumed to be Hall 3. Follow the manufacturer’s grounding instructions.