Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
Haltech standalone ECUs
Applies to
Haltech standalone ECUs
Tool groups
None
Manufacturers
None

Changes from revision 1 to revision 1

Removed text is struck through; added text is highlighted.

Haltech Nexus Plug-in Honda DC5 2005–2006 is a vehicle-specific, direct plug-in programmable ECU, Haltech part HT-231011, that replaces the original engine ECU. Haltech product listing.

Haltech Nexus Honda plug-in ECU. The same manufacturer photograph appears on the EP3 and DC5 product listings; confirm the part number and connector application. Haltech product photograph, reproduced with permission.

Applications and identification

The HT-231011 is listed by Haltech for the 2005–2006 Honda Integra / Acura RSX DC5, manual transmission only. It is a distinct vehicle application from HT-231001; the two charts have different connector assignments. The manufacturer says a K24A swap is supported when the original vehicle engine harness is retained for the correct pin assignments.

Haltech says the original four-wire wideband sensor is not supported and calls for an LSU 4.9 or NTK sensor via the auxiliary connector. The ECU has an onboard 4-bar MAP sensor; its vacuum connection must be connected if used. Manufacturer details are in the Honda Nexus installation guide.

Vehicle connector assignments

These 86 assignments reproduce the Haltech 231011 quick-start guide, PDF page 7, manufacturer document hosted by a retailer. View is the ECU pin side; Haltech marks vehicle connectors C and D unused. Use the chart for this exact part number; calibratable outputs depend on setup.

Vehicle connector A

PinECU connectionManufacturer functionA1Knock 1Knock sensorA2+12V ECU powerECU switched power supplyA3+12V ECU powerECU switched power supplyA4Power groundBattery groundA5Power groundBattery groundA6HomeExhaust cam sensorA7TriggerCrank sensorA8Power groundBattery groundA9Power groundBattery groundA10UnusedNo connectionA11DPO 5Dual intake runner system (IMRC)A12DPO 6Idle controlA13Ignition 4Ignition output for cylinder 4A14Ignition 3Ignition output for cylinder 3A15Ignition 2Ignition output for cylinder 2A16Ignition 1Ignition output for cylinder 1A17UnusedNo connectionA18SPI 5Vehicle speed sensorA19SPI 6Intake cam sensorA20+5V DC+5V sensor supplyA21+5V DC+5V sensor supplyA22UnusedNo connectionA23Sensor groundSensor groundA24Sensor groundSensor groundA25AVI 6Spare AVIA26AVI 5Spare AVIA27UnusedNo connectionA28UnusedNo connectionA29AVI 10Throttle position sensorA30AVI 9MAP sensorA31UnusedNo connection

Vehicle connector B

PinECU connectionManufacturer functionB1HBO 3Intake VTC solenoid controlB2Injector 4Injector output for cylinder 4B3Injector 3Injector output for cylinder 3B4Injector 2Injector output for cylinder 2B5Injector 1Injector output for cylinder 1B6HBO 4VTEC solenoidB7UnusedNo connectionB8AVI 8Coolant temperature sensorB9UnusedNo connectionB10AVI 18Alternator LB11AVI 13Oil pressure switch (VTEC)B12UnusedNo connectionB13AVI 19Alternator FRB14UnusedNo connectionB15UnusedNo connectionB16UnusedNo connectionB17AVI 7Intake air temperature sensorB18DPO 17Alternator control outputB19UnusedNo connectionB20UnusedNo connectionB21DPO 12Evap purge valve solenoidB22AVI 12Dual intake runner position inputB23UnusedNo connectionB24UnusedNo connection

Vehicle connector E

PinECU connectionManufacturer functionE1UnusedNo connectionE2DPO 8Reverse lockout solenoidE3Power groundImmobilizer groundE4Sensor groundSensor groundE5+5V DC+5V sensor supplyE6UnusedNo connectionE7ECREngine control relay outputE8UnusedNo connectionE9Ign SW InputIgnition switchE10UnusedNo connectionE11UnusedNo connectionE12DPO 10Thermofan relay outputE13Multiplex serial commsMultiplex serial communicationsE14AVI 14Fuel tank pressure sensorE15AVI 15Electrical load detector inputE16AVI 11Power steering switch inputE17DPO 11Fuel pump relay outputE18DPO 14A/C relay outputE19DPO 13Evap vent shut valveE20AVI 17Narrowband O2 sensor inputE21DPO 7O2 sensor heater outputE22AVI 16Brake pedal switch inputE23UnusedNo connectionE24UnusedNo connectionE25DPO 16Tachometer outputE26DPO 15VSS output to dashE27Immobilizer commsImmobilizer serial communicationsE28UnusedNo connectionE29UnusedNo connectionE30UnusedNo connectionE31DPO 9Check engine light

26-pin auxiliary connector

The following table is the ECU auxiliary connector, pin-side view, from the same manufacturer guide, page 8. It is distinct from the vehicle ECU connectors above. Haltech states switched 12 V from the onboard CAN and auxiliary connectors is limited to 8 A total across the three pins.

PinHaltech connectionHarness colour1DPO 1Violet / Blue2DPO 3Violet / Red3Aux power (12V switched)Red4Sensor groundBlack / White5SPI 1Gray / Brown6SPI 3Gray / Orange7HBO 1Brown / Black8AVI 1White9AVI 3White / Gray10Sensor groundBlack / White11WBI 1 Heater +Gray12WBI 1 InputYellow13WBI 1 PumpRed14DPO 2Violet / Brown15DPO 4Violet / Orange16Aux power (12V switched)Red17Sensor +5V DCOrange18SPI 2Gray / Red19SPI 4Gray / Yellow20HBO 2Brown / Red21AVI 2White / Yellow22AVI 4White / Violet23Sensor +5V DCOrange24WBI 1 NernstBlack25WBI 1 Heater -White26WBI 1 CalGreen

Software

Nexus Software Programmer (NSP) configures and tunes the ECU; USB-C and optional Wi-Fi communication are described in Haltech’s installation guide. The setup wizard provides a starting configuration and the engine requires appropriate tuning.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Haltech Nexus Plug-in Honda DC5 2005–2006

Haltech Nexus Plug-in Honda DC5 2005–2006 is a vehicle-specific, direct plug-in programmable ECU, Haltech part HT-231011, that replaces the original engine ECU. Haltech product listing.

Haltech Nexus Honda plug-in ECU
Haltech Nexus Honda plug-in ECU. The same manufacturer photograph appears on the EP3 and DC5 product listings; confirm the part number and connector application. Haltech product photograph, reproduced with permission.

Applications and identification

The HT-231011 is listed by Haltech for the 2005–2006 Honda Integra / Acura RSX DC5, manual transmission only. It is a distinct vehicle application from HT-231001; the two charts have different connector assignments. The manufacturer says a K24A swap is supported when the original vehicle engine harness is retained for the correct pin assignments.

Haltech says the original four-wire wideband sensor is not supported and calls for an LSU 4.9 or NTK sensor via the auxiliary connector. The ECU has an onboard 4-bar MAP sensor; its vacuum connection must be connected if used. Manufacturer details are in the Honda Nexus installation guide.

Vehicle connector assignments

These 86 assignments reproduce the Haltech 231011 quick-start guide, PDF page 7, manufacturer document hosted by a retailer. View is the ECU pin side; Haltech marks vehicle connectors C and D unused. Use the chart for this exact part number; calibratable outputs depend on setup.

Vehicle connector A

PinECU connectionManufacturer function
A1Knock 1Knock sensor
A2+12V ECU powerECU switched power supply
A3+12V ECU powerECU switched power supply
A4Power groundBattery ground
A5Power groundBattery ground
A6HomeExhaust cam sensor
A7TriggerCrank sensor
A8Power groundBattery ground
A9Power groundBattery ground
A10UnusedNo connection
A11DPO 5Dual intake runner system (IMRC)
A12DPO 6Idle control
A13Ignition 4Ignition output for cylinder 4
A14Ignition 3Ignition output for cylinder 3
A15Ignition 2Ignition output for cylinder 2
A16Ignition 1Ignition output for cylinder 1
A17UnusedNo connection
A18SPI 5Vehicle speed sensor
A19SPI 6Intake cam sensor
A20+5V DC+5V sensor supply
A21+5V DC+5V sensor supply
A22UnusedNo connection
A23Sensor groundSensor ground
A24Sensor groundSensor ground
A25AVI 6Spare AVI
A26AVI 5Spare AVI
A27UnusedNo connection
A28UnusedNo connection
A29AVI 10Throttle position sensor
A30AVI 9MAP sensor
A31UnusedNo connection

Vehicle connector B

PinECU connectionManufacturer function
B1HBO 3Intake VTC solenoid control
B2Injector 4Injector output for cylinder 4
B3Injector 3Injector output for cylinder 3
B4Injector 2Injector output for cylinder 2
B5Injector 1Injector output for cylinder 1
B6HBO 4VTEC solenoid
B7UnusedNo connection
B8AVI 8Coolant temperature sensor
B9UnusedNo connection
B10AVI 18Alternator L
B11AVI 13Oil pressure switch (VTEC)
B12UnusedNo connection
B13AVI 19Alternator FR
B14UnusedNo connection
B15UnusedNo connection
B16UnusedNo connection
B17AVI 7Intake air temperature sensor
B18DPO 17Alternator control output
B19UnusedNo connection
B20UnusedNo connection
B21DPO 12Evap purge valve solenoid
B22AVI 12Dual intake runner position input
B23UnusedNo connection
B24UnusedNo connection

Vehicle connector E

PinECU connectionManufacturer function
E1UnusedNo connection
E2DPO 8Reverse lockout solenoid
E3Power groundImmobilizer ground
E4Sensor groundSensor ground
E5+5V DC+5V sensor supply
E6UnusedNo connection
E7ECREngine control relay output
E8UnusedNo connection
E9Ign SW InputIgnition switch
E10UnusedNo connection
E11UnusedNo connection
E12DPO 10Thermofan relay output
E13Multiplex serial commsMultiplex serial communications
E14AVI 14Fuel tank pressure sensor
E15AVI 15Electrical load detector input
E16AVI 11Power steering switch input
E17DPO 11Fuel pump relay output
E18DPO 14A/C relay output
E19DPO 13Evap vent shut valve
E20AVI 17Narrowband O2 sensor input
E21DPO 7O2 sensor heater output
E22AVI 16Brake pedal switch input
E23UnusedNo connection
E24UnusedNo connection
E25DPO 16Tachometer output
E26DPO 15VSS output to dash
E27Immobilizer commsImmobilizer serial communications
E28UnusedNo connection
E29UnusedNo connection
E30UnusedNo connection
E31DPO 9Check engine light

26-pin auxiliary connector

The following table is the ECU auxiliary connector, pin-side view, from the same manufacturer guide, page 8. It is distinct from the vehicle ECU connectors above. Haltech states switched 12 V from the onboard CAN and auxiliary connectors is limited to 8 A total across the three pins.

PinHaltech connectionHarness colour
1DPO 1Violet / Blue
2DPO 3Violet / Red
3Aux power (12V switched)Red
4Sensor groundBlack / White
5SPI 1Gray / Brown
6SPI 3Gray / Orange
7HBO 1Brown / Black
8AVI 1White
9AVI 3White / Gray
10Sensor groundBlack / White
11WBI 1 Heater +Gray
12WBI 1 InputYellow
13WBI 1 PumpRed
14DPO 2Violet / Brown
15DPO 4Violet / Orange
16Aux power (12V switched)Red
17Sensor +5V DCOrange
18SPI 2Gray / Red
19SPI 4Gray / Yellow
20HBO 2Brown / Red
21AVI 2White / Yellow
22AVI 4White / Violet
23Sensor +5V DCOrange
24WBI 1 NernstBlack
25WBI 1 Heater -White
26WBI 1 CalGreen

Software

Nexus Software Programmer (NSP) configures and tunes the ECU; USB-C and optional Wi-Fi communication are described in Haltech’s installation guide. The setup wizard provides a starting configuration and the engine requires appropriate tuning.

Revision 1: Haltech Nexus Plug-in Honda DC5 2005–2006

Haltech Nexus Plug-in Honda DC5 2005–2006 is a vehicle-specific, direct plug-in programmable ECU, Haltech part HT-231011, that replaces the original engine ECU. Haltech product listing.

Haltech Nexus Honda plug-in ECU
Haltech Nexus Honda plug-in ECU. The same manufacturer photograph appears on the EP3 and DC5 product listings; confirm the part number and connector application. Haltech product photograph, reproduced with permission.

Applications and identification

The HT-231011 is listed by Haltech for the 2005–2006 Honda Integra / Acura RSX DC5, manual transmission only. It is a distinct vehicle application from HT-231001; the two charts have different connector assignments. The manufacturer says a K24A swap is supported when the original vehicle engine harness is retained for the correct pin assignments.

Haltech says the original four-wire wideband sensor is not supported and calls for an LSU 4.9 or NTK sensor via the auxiliary connector. The ECU has an onboard 4-bar MAP sensor; its vacuum connection must be connected if used. Manufacturer details are in the Honda Nexus installation guide.

Vehicle connector assignments

These 86 assignments reproduce the Haltech 231011 quick-start guide, PDF page 7, manufacturer document hosted by a retailer. View is the ECU pin side; Haltech marks vehicle connectors C and D unused. Use the chart for this exact part number; calibratable outputs depend on setup.

Vehicle connector A

PinECU connectionManufacturer function
A1Knock 1Knock sensor
A2+12V ECU powerECU switched power supply
A3+12V ECU powerECU switched power supply
A4Power groundBattery ground
A5Power groundBattery ground
A6HomeExhaust cam sensor
A7TriggerCrank sensor
A8Power groundBattery ground
A9Power groundBattery ground
A10UnusedNo connection
A11DPO 5Dual intake runner system (IMRC)
A12DPO 6Idle control
A13Ignition 4Ignition output for cylinder 4
A14Ignition 3Ignition output for cylinder 3
A15Ignition 2Ignition output for cylinder 2
A16Ignition 1Ignition output for cylinder 1
A17UnusedNo connection
A18SPI 5Vehicle speed sensor
A19SPI 6Intake cam sensor
A20+5V DC+5V sensor supply
A21+5V DC+5V sensor supply
A22UnusedNo connection
A23Sensor groundSensor ground
A24Sensor groundSensor ground
A25AVI 6Spare AVI
A26AVI 5Spare AVI
A27UnusedNo connection
A28UnusedNo connection
A29AVI 10Throttle position sensor
A30AVI 9MAP sensor
A31UnusedNo connection

Vehicle connector B

PinECU connectionManufacturer function
B1HBO 3Intake VTC solenoid control
B2Injector 4Injector output for cylinder 4
B3Injector 3Injector output for cylinder 3
B4Injector 2Injector output for cylinder 2
B5Injector 1Injector output for cylinder 1
B6HBO 4VTEC solenoid
B7UnusedNo connection
B8AVI 8Coolant temperature sensor
B9UnusedNo connection
B10AVI 18Alternator L
B11AVI 13Oil pressure switch (VTEC)
B12UnusedNo connection
B13AVI 19Alternator FR
B14UnusedNo connection
B15UnusedNo connection
B16UnusedNo connection
B17AVI 7Intake air temperature sensor
B18DPO 17Alternator control output
B19UnusedNo connection
B20UnusedNo connection
B21DPO 12Evap purge valve solenoid
B22AVI 12Dual intake runner position input
B23UnusedNo connection
B24UnusedNo connection

Vehicle connector E

PinECU connectionManufacturer function
E1UnusedNo connection
E2DPO 8Reverse lockout solenoid
E3Power groundImmobilizer ground
E4Sensor groundSensor ground
E5+5V DC+5V sensor supply
E6UnusedNo connection
E7ECREngine control relay output
E8UnusedNo connection
E9Ign SW InputIgnition switch
E10UnusedNo connection
E11UnusedNo connection
E12DPO 10Thermofan relay output
E13Multiplex serial commsMultiplex serial communications
E14AVI 14Fuel tank pressure sensor
E15AVI 15Electrical load detector input
E16AVI 11Power steering switch input
E17DPO 11Fuel pump relay output
E18DPO 14A/C relay output
E19DPO 13Evap vent shut valve
E20AVI 17Narrowband O2 sensor input
E21DPO 7O2 sensor heater output
E22AVI 16Brake pedal switch input
E23UnusedNo connection
E24UnusedNo connection
E25DPO 16Tachometer output
E26DPO 15VSS output to dash
E27Immobilizer commsImmobilizer serial communications
E28UnusedNo connection
E29UnusedNo connection
E30UnusedNo connection
E31DPO 9Check engine light

26-pin auxiliary connector

The following table is the ECU auxiliary connector, pin-side view, from the same manufacturer guide, page 8. It is distinct from the vehicle ECU connectors above. Haltech states switched 12 V from the onboard CAN and auxiliary connectors is limited to 8 A total across the three pins.

PinHaltech connectionHarness colour
1DPO 1Violet / Blue
2DPO 3Violet / Red
3Aux power (12V switched)Red
4Sensor groundBlack / White
5SPI 1Gray / Brown
6SPI 3Gray / Orange
7HBO 1Brown / Black
8AVI 1White
9AVI 3White / Gray
10Sensor groundBlack / White
11WBI 1 Heater +Gray
12WBI 1 InputYellow
13WBI 1 PumpRed
14DPO 2Violet / Brown
15DPO 4Violet / Orange
16Aux power (12V switched)Red
17Sensor +5V DCOrange
18SPI 2Gray / Red
19SPI 4Gray / Yellow
20HBO 2Brown / Red
21AVI 2White / Yellow
22AVI 4White / Violet
23Sensor +5V DCOrange
24WBI 1 NernstBlack
25WBI 1 Heater -White
26WBI 1 CalGreen

Software

Nexus Software Programmer (NSP) configures and tunes the ECU; USB-C and optional Wi-Fi communication are described in Haltech’s installation guide. The setup wizard provides a starting configuration and the engine requires appropriate tuning.