Haltech Nexus Plug-in Honda DC5 2005–2006 is a vehicle-specific, direct plug-in programmable ECU, Haltech part HT-231011, that replaces the original engine ECU. Haltech product listing.

Applications and identification
The HT-231011 is listed by Haltech for the 2005–2006 Honda Integra / Acura RSX DC5, manual transmission only. It is a distinct vehicle application from HT-231001; the two charts have different connector assignments. The manufacturer says a K24A swap is supported when the original vehicle engine harness is retained for the correct pin assignments.
Haltech says the original four-wire wideband sensor is not supported and calls for an LSU 4.9 or NTK sensor via the auxiliary connector. The ECU has an onboard 4-bar MAP sensor; its vacuum connection must be connected if used. Manufacturer details are in the Honda Nexus installation guide.
Vehicle connector assignments
These 86 assignments reproduce the Haltech 231011 quick-start guide, PDF page 7, manufacturer document hosted by a retailer. View is the ECU pin side; Haltech marks vehicle connectors C and D unused. Use the chart for this exact part number; calibratable outputs depend on setup.
Vehicle connector A
| Pin | ECU connection | Manufacturer function |
|---|---|---|
| A1 | Knock 1 | Knock sensor |
| A2 | +12V ECU power | ECU switched power supply |
| A3 | +12V ECU power | ECU switched power supply |
| A4 | Power ground | Battery ground |
| A5 | Power ground | Battery ground |
| A6 | Home | Exhaust cam sensor |
| A7 | Trigger | Crank sensor |
| A8 | Power ground | Battery ground |
| A9 | Power ground | Battery ground |
| A10 | Unused | No connection |
| A11 | DPO 5 | Dual intake runner system (IMRC) |
| A12 | DPO 6 | Idle control |
| A13 | Ignition 4 | Ignition output for cylinder 4 |
| A14 | Ignition 3 | Ignition output for cylinder 3 |
| A15 | Ignition 2 | Ignition output for cylinder 2 |
| A16 | Ignition 1 | Ignition output for cylinder 1 |
| A17 | Unused | No connection |
| A18 | SPI 5 | Vehicle speed sensor |
| A19 | SPI 6 | Intake cam sensor |
| A20 | +5V DC | +5V sensor supply |
| A21 | +5V DC | +5V sensor supply |
| A22 | Unused | No connection |
| A23 | Sensor ground | Sensor ground |
| A24 | Sensor ground | Sensor ground |
| A25 | AVI 6 | Spare AVI |
| A26 | AVI 5 | Spare AVI |
| A27 | Unused | No connection |
| A28 | Unused | No connection |
| A29 | AVI 10 | Throttle position sensor |
| A30 | AVI 9 | MAP sensor |
| A31 | Unused | No connection |
Vehicle connector B
| Pin | ECU connection | Manufacturer function |
|---|---|---|
| B1 | HBO 3 | Intake VTC solenoid control |
| B2 | Injector 4 | Injector output for cylinder 4 |
| B3 | Injector 3 | Injector output for cylinder 3 |
| B4 | Injector 2 | Injector output for cylinder 2 |
| B5 | Injector 1 | Injector output for cylinder 1 |
| B6 | HBO 4 | VTEC solenoid |
| B7 | Unused | No connection |
| B8 | AVI 8 | Coolant temperature sensor |
| B9 | Unused | No connection |
| B10 | AVI 18 | Alternator L |
| B11 | AVI 13 | Oil pressure switch (VTEC) |
| B12 | Unused | No connection |
| B13 | AVI 19 | Alternator FR |
| B14 | Unused | No connection |
| B15 | Unused | No connection |
| B16 | Unused | No connection |
| B17 | AVI 7 | Intake air temperature sensor |
| B18 | DPO 17 | Alternator control output |
| B19 | Unused | No connection |
| B20 | Unused | No connection |
| B21 | DPO 12 | Evap purge valve solenoid |
| B22 | AVI 12 | Dual intake runner position input |
| B23 | Unused | No connection |
| B24 | Unused | No connection |
Vehicle connector E
| Pin | ECU connection | Manufacturer function |
|---|---|---|
| E1 | Unused | No connection |
| E2 | DPO 8 | Reverse lockout solenoid |
| E3 | Power ground | Immobilizer ground |
| E4 | Sensor ground | Sensor ground |
| E5 | +5V DC | +5V sensor supply |
| E6 | Unused | No connection |
| E7 | ECR | Engine control relay output |
| E8 | Unused | No connection |
| E9 | Ign SW Input | Ignition switch |
| E10 | Unused | No connection |
| E11 | Unused | No connection |
| E12 | DPO 10 | Thermofan relay output |
| E13 | Multiplex serial comms | Multiplex serial communications |
| E14 | AVI 14 | Fuel tank pressure sensor |
| E15 | AVI 15 | Electrical load detector input |
| E16 | AVI 11 | Power steering switch input |
| E17 | DPO 11 | Fuel pump relay output |
| E18 | DPO 14 | A/C relay output |
| E19 | DPO 13 | Evap vent shut valve |
| E20 | AVI 17 | Narrowband O2 sensor input |
| E21 | DPO 7 | O2 sensor heater output |
| E22 | AVI 16 | Brake pedal switch input |
| E23 | Unused | No connection |
| E24 | Unused | No connection |
| E25 | DPO 16 | Tachometer output |
| E26 | DPO 15 | VSS output to dash |
| E27 | Immobilizer comms | Immobilizer serial communications |
| E28 | Unused | No connection |
| E29 | Unused | No connection |
| E30 | Unused | No connection |
| E31 | DPO 9 | Check engine light |
26-pin auxiliary connector
The following table is the ECU auxiliary connector, pin-side view, from the same manufacturer guide, page 8. It is distinct from the vehicle ECU connectors above. Haltech states switched 12 V from the onboard CAN and auxiliary connectors is limited to 8 A total across the three pins.
| Pin | Haltech connection | Harness colour |
|---|---|---|
| 1 | DPO 1 | Violet / Blue |
| 2 | DPO 3 | Violet / Red |
| 3 | Aux power (12V switched) | Red |
| 4 | Sensor ground | Black / White |
| 5 | SPI 1 | Gray / Brown |
| 6 | SPI 3 | Gray / Orange |
| 7 | HBO 1 | Brown / Black |
| 8 | AVI 1 | White |
| 9 | AVI 3 | White / Gray |
| 10 | Sensor ground | Black / White |
| 11 | WBI 1 Heater + | Gray |
| 12 | WBI 1 Input | Yellow |
| 13 | WBI 1 Pump | Red |
| 14 | DPO 2 | Violet / Brown |
| 15 | DPO 4 | Violet / Orange |
| 16 | Aux power (12V switched) | Red |
| 17 | Sensor +5V DC | Orange |
| 18 | SPI 2 | Gray / Red |
| 19 | SPI 4 | Gray / Yellow |
| 20 | HBO 2 | Brown / Red |
| 21 | AVI 2 | White / Yellow |
| 22 | AVI 4 | White / Violet |
| 23 | Sensor +5V DC | Orange |
| 24 | WBI 1 Nernst | Black |
| 25 | WBI 1 Heater - | White |
| 26 | WBI 1 Cal | Green |
Software
Nexus Software Programmer (NSP) configures and tunes the ECU; USB-C and optional Wi-Fi communication are described in Haltech’s installation guide. The setup wizard provides a starting configuration and the engine requires appropriate tuning.