Removed text is struck through; added text is highlighted.
Holley Super Sniper EFI 2300 is a carburettor-replacement throttle-body fuel-injection system with integrated electronic control. The handheld is a setup/display device, and the system also requires appropriate fuel delivery, wiring and sensors.
Holley Holley Super Sniper EFI 2300 family illustration from its installation manual, cover; finish and injector count vary with part number. Manufacturer photograph reproduced with permission.
Applications and versions
Designed for a Holley 2300-style two-barrel intake flange. Holley lists the four-injector Super Sniper for boosted applications; select injectors, calibration and fuel delivery for the engine.
Four injectors with boost-control provisions and an integrated ECU. The 550-852, 550-853 and 550-854 are listed as finish variants; it differs from the two-injector 2300. Model numbers: 550-852 / 550-853 / 550-854. See Holley’s Sniper model comparison.
Manufacturer harness connections
The model-specific Holley installation manual, PDF page 18, identifies the seven-way 558-490 main harness and ten-way 558-491 I/O harness below. The ten-way table has eight populated wires; the source does not assign the remaining two cavities. Outputs are relay-control signals: use the source for ratings, ignition configuration and the connector view. The throttle body, 4-pin CAN handheld connection, coolant sensor and oxygen sensor are separate connections.
Seven-way main harness, 558-490
PinWire colourManufacturer functionAVioletCrank signal positiveBDark greenCrank signal negativeCBlueFuel-pump supply from relayDYellowCoil-negative engine-speed inputERedBattery positiveFPinkSwitched ignition +12 VGBlackBattery negative
The correct fuel pump, filters, sensor placement and ignition setup depend on the kit and vehicle. An RPM input alone does not establish ECU timing control; consult the manual and identify the ignition hardware before wiring.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Holley Super Sniper EFI 2300
Holley Super Sniper EFI 2300 is a carburettor-replacement throttle-body fuel-injection system with integrated electronic control. The handheld is a setup/display device, and the system also requires appropriate fuel delivery, wiring and sensors.
Holley Holley Super Sniper EFI 2300 family illustration from its installation manual, cover; finish and injector count vary with part number. Manufacturer photograph reproduced with permission.
Applications and versions
Designed for a Holley 2300-style two-barrel intake flange. Holley lists the four-injector Super Sniper for boosted applications; select injectors, calibration and fuel delivery for the engine.
Four injectors with boost-control provisions and an integrated ECU. The 550-852, 550-853 and 550-854 are listed as finish variants; it differs from the two-injector 2300. Model numbers: 550-852 / 550-853 / 550-854. See Holley’s Sniper model comparison.
Manufacturer harness connections
The model-specific Holley installation manual, PDF page 18, identifies the seven-way 558-490 main harness and ten-way 558-491 I/O harness below. The ten-way table has eight populated wires; the source does not assign the remaining two cavities. Outputs are relay-control signals: use the source for ratings, ignition configuration and the connector view. The throttle body, 4-pin CAN handheld connection, coolant sensor and oxygen sensor are separate connections.
Seven-way main harness, 558-490
Pin
Wire colour
Manufacturer function
A
Violet
Crank signal positive
B
Dark green
Crank signal negative
C
Blue
Fuel-pump supply from relay
D
Yellow
Coil-negative engine-speed input
E
Red
Battery positive
F
Pink
Switched ignition +12 V
G
Black
Battery negative
Ten-way I/O harness, 558-491
Pin
Wire colour
Manufacturer function
A
Orange
Input 1, ground-triggered A/C
B
Yellow
Input 2, programmable ground input
C
Light blue
Output 1, fan 1 relay trigger
D
Light green
Output 2, fan 2 relay trigger
E
Grey
Output 6, A/C shutdown relay trigger
F
White
Points output for compatible ignition
G
Dark brown
Tachometer output
H
Tan
Digital gauge output
Eight-way auxiliary I/O harness, 558-492
Optional harness for this Super Sniper or Stealth application.
Pin
Wire colour
Manufacturer function
A
Orange
Sensor reference +5 V
B
Black
Sensor ground
C
Violet
Input 3, 0–5 V
D
Pink
Input 4, 0–5 V
E
Dark green
Input 5, 0–5 V
F
Dark blue
Output 3, ground-switched
G
Dark brown
Output 4, ground-switched
H
Grey
Output 5, ground-switched
Installation and ignition
The correct fuel pump, filters, sensor placement and ignition setup depend on the kit and vehicle. An RPM input alone does not establish ECU timing control; consult the manual and identify the ignition hardware before wiring.
Revision 1: Holley Super Sniper EFI 2300
Holley Super Sniper EFI 2300 is a carburettor-replacement throttle-body fuel-injection system with integrated electronic control. The handheld is a setup/display device, and the system also requires appropriate fuel delivery, wiring and sensors.
Holley Holley Super Sniper EFI 2300 family illustration from its installation manual, cover; finish and injector count vary with part number. Manufacturer photograph reproduced with permission.
Applications and versions
Designed for a Holley 2300-style two-barrel intake flange. Holley lists the four-injector Super Sniper for boosted applications; select injectors, calibration and fuel delivery for the engine.
Four injectors with boost-control provisions and an integrated ECU. The 550-852, 550-853 and 550-854 are listed as finish variants; it differs from the two-injector 2300. Model numbers: 550-852 / 550-853 / 550-854. See Holley’s Sniper model comparison.
Manufacturer harness connections
The model-specific Holley installation manual, PDF page 18, identifies the seven-way 558-490 main harness and ten-way 558-491 I/O harness below. The ten-way table has eight populated wires; the source does not assign the remaining two cavities. Outputs are relay-control signals: use the source for ratings, ignition configuration and the connector view. The throttle body, 4-pin CAN handheld connection, coolant sensor and oxygen sensor are separate connections.
Seven-way main harness, 558-490
Pin
Wire colour
Manufacturer function
A
Violet
Crank signal positive
B
Dark green
Crank signal negative
C
Blue
Fuel-pump supply from relay
D
Yellow
Coil-negative engine-speed input
E
Red
Battery positive
F
Pink
Switched ignition +12 V
G
Black
Battery negative
Ten-way I/O harness, 558-491
Pin
Wire colour
Manufacturer function
A
Orange
Input 1, ground-triggered A/C
B
Yellow
Input 2, programmable ground input
C
Light blue
Output 1, fan 1 relay trigger
D
Light green
Output 2, fan 2 relay trigger
E
Grey
Output 6, A/C shutdown relay trigger
F
White
Points output for compatible ignition
G
Dark brown
Tachometer output
H
Tan
Digital gauge output
Eight-way auxiliary I/O harness, 558-492
Optional harness for this Super Sniper or Stealth application.
Pin
Wire colour
Manufacturer function
A
Orange
Sensor reference +5 V
B
Black
Sensor ground
C
Violet
Input 3, 0–5 V
D
Pink
Input 4, 0–5 V
E
Dark green
Input 5, 0–5 V
F
Dark blue
Output 3, ground-switched
G
Dark brown
Output 4, ground-switched
H
Grey
Output 5, ground-switched
Installation and ignition
The correct fuel pump, filters, sensor placement and ignition setup depend on the kit and vehicle. An RPM input alone does not establish ECU timing control; consult the manual and identify the ignition hardware before wiring.