Removed text is struck through; added text is highlighted.
PnPduino Universal8 is a PnPduino programmable engine-management ECU. Manufacturer product information.
PnPduino Universal8. PnPduino manufacturer product photograph, reproduced with permission.
Application and identification
An upgraded configurable wire-in ECU that the manufacturer describes for up to eight cylinders with sequential injection and ignition. It can be used as standalone or piggyback; the listing specifies manual transmission and cable-throttle operation.
System and wiring
Separate 34-position AMP Superseal 1.0 connectors are used for inputs and outputs, with three-slot and four-slot housings respectively. The STM32-MEGA processor provides CAN and onboard microSD logging according to the listing. Internal MAP, Bluetooth, VR conditioner, stepper driver and wideband are optional. The ASA/ABS case is not waterproof and is intended for installation inside the car.
The manufacturer’s model-specific connector schedule is transcribed below. Confirm the hardware revision, optional equipment and calibration before wiring.A complete pin-by-pin ECU connector table has not been verified from the cited product information. Obtain the diagram for the exact model and revision from PnPduino documentation; the vehicle ECU pinout and other PnPduino models must not be assumed interchangeable.
Software and calibration
The product lists TunerStudio and official Speeduino firmware. Verify outputs, sensors and firmware for the actual build and obtain the model-specific pinout before wiring.
See the PnPduino manufacturer index.
Model-specific wiring document
The manufacturer provides the revision 2 Universal8 two-connector drawing; verify the hardware revision and actual build before using its assignments. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the full manufacturer-labelled schedule follows below.PnPduino Universal8 manufacturer connector scheduleTranscribed from the PnPduino PnPduino Universal8 pinout revision 2. Follow the connector drawing in the source and verify the actual build and orientation; the source does not explicitly identify its view as ECU-face or wire-side. Arduino pins are software/board assignments, not connector cavity numbers. A blank manufacturer label is recorded as unlabelled rather than assumed unused.A-plug input — 34 positionsECU pinManufacturer labelManufacturer descriptionArduino pinA1INP4Spare Input 4A11A2INP1Spare Input 1A8A3CLTEngine Coolant TempA4A4O2Wideband O2 SensorA1A5CANHCAN HiSTM32A6VR2+VR2+ or Hall Sensor 2D18A7VR1+VR1+ or Hall Sensor 1D19A85V Out5V Out to sensors—A912V In12V Input from Ignition switch—A10INP3Spare Input 3A10A11IATIntake Air TemperatureA5A12TPSThrottle Position SensorA3A13CLUTCHClutch Switch37A14CANLCAN LoSTM32A15VR2-VR2- or Hall Sensor 2 Logic Ground—A16VR1-VR1- or Hall Sensor 1 Logic Ground—A17INP5Spare Input 5A6A18INP9Spare Input 9A15A19INP2Spare Input 2A9A2012V OutFused 12V Supply to sensors only—A2112V OutFused 12V Supply to sensors only—A2212V OutFused 12V Supply to sensors only—A2312V OutFused 12V Supply to sensors only—A24Not labelled in sourceNot labelled in source—A25INP7Spare Input 7A13A26EXTMAPExternal MAP sensorA0A27INP8Spare Input 8A14A28FLEXFlex Fuel Sensor2A29HALL4Hall Sensor 43A30GRNDECU Logic Ground—A31GRNDPower Ground—A32GRNDSensor Ground—A33Not labelled in sourceNot labelled in source—A34INP6Spare Input 6A12B-plug output — 34 positionsECU pinManufacturer labelManufacturer descriptionArduino pinB1VVTVVT/VVTI or VTEC/VTC terminology11B2IDLE2Idle 2 or Spare High Current 110B3IDLE1Idle 1 for IACV Solenoid9B4INJ4Injector 45B5INJ3Injector 36B6INJ2Injector 27B7INJ1Injector 18B8INJ8Injector 849B9INJ7Injector 747B10BOOSTBoost or Spare Hi Current 212B11LC4Low Current Output 429B12LC3Low Current Output 328B13LC1Low Current Output 126B14FANRadiator Fan 124B15TACHTachometer Output 5V or 12V22B16FUELPFuel Pump or Circuit Opening Relay23B17INJ6Injector 645B18IGN4Ignition Output 434B19IGN3Ignition Output 333B20STP-B2Stepper Idle Air Coil B2—B21STP-A2Stepper Idle Air Coil A2—B22FAN2Radiator Fan 225B23GRNDPower Ground—B24GRNDPower Ground—B25INJ5Injector 542B26IGN1Ignition Output 135B27IGN2Ignition Output 236B28STP-B1Stepper Idle Air Coil B1—B29STP-A1Stepper Idle Air Coil A1—B30LC2Low Current Output 227B31IGN8Ignition Output 841B32IGN7Ignition Output 740B33IGN6Ignition Output 639B34IGN5Ignition Output 538The revision-2 source states that IDLE2 and BOOST can be used as high-current outputs and that a PWM radiator fan should use FAN2. It says vehicle speed can be wired to Hall 3, but does not assign Hall 3 a cavity in this table; A24 and A33 are blank and are not assumed to be Hall 3. Follow the manufacturer’s grounding instructions.The manufacturer provides the revision 2 Universal8 two-connector drawing; verify the hardware revision and actual build before using its assignments. Open the PnPduino pinout document. The page’s connector-identification table is not a complete cavity-by-cavity schedule.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
An upgraded configurable wire-in ECU that the manufacturer describes for up to eight cylinders with sequential injection and ignition. It can be used as standalone or piggyback; the listing specifies manual transmission and cable-throttle operation.
System and wiring
Separate 34-position AMP Superseal 1.0 connectors are used for inputs and outputs, with three-slot and four-slot housings respectively. The STM32-MEGA processor provides CAN and onboard microSD logging according to the listing. Internal MAP, Bluetooth, VR conditioner, stepper driver and wideband are optional. The ASA/ABS case is not waterproof and is intended for installation inside the car.
Connector identification
Connector
Manufacturer description
Scope
Input header
34 positions, AMP Superseal 1.0, three-slot
Manufacturer product listing
Output header
34 positions, AMP Superseal 1.0, four-slot
Manufacturer product listing
A complete pin-by-pin ECU connector table has not been verified from the cited product information. Obtain the diagram for the exact model and revision from PnPduino documentation; the vehicle ECU pinout and other PnPduino models must not be assumed interchangeable.
Software and calibration
The product lists TunerStudio and official Speeduino firmware. Verify outputs, sensors and firmware for the actual build and obtain the model-specific pinout before wiring.
The manufacturer provides the revision 2 Universal8 two-connector drawing; verify the hardware revision and actual build before using its assignments. Open the PnPduino pinout document. The page’s connector-identification table is not a complete cavity-by-cavity schedule.
An upgraded configurable wire-in ECU that the manufacturer describes for up to eight cylinders with sequential injection and ignition. It can be used as standalone or piggyback; the listing specifies manual transmission and cable-throttle operation.
System and wiring
Separate 34-position AMP Superseal 1.0 connectors are used for inputs and outputs, with three-slot and four-slot housings respectively. The STM32-MEGA processor provides CAN and onboard microSD logging according to the listing. Internal MAP, Bluetooth, VR conditioner, stepper driver and wideband are optional. The ASA/ABS case is not waterproof and is intended for installation inside the car.
Connector identification
Connector
Manufacturer description
Scope
Input header
34 positions, AMP Superseal 1.0, three-slot
Manufacturer product listing
Output header
34 positions, AMP Superseal 1.0, four-slot
Manufacturer product listing
The manufacturer’s model-specific connector schedule is transcribed below. Confirm the hardware revision, optional equipment and calibration before wiring.
Software and calibration
The product lists TunerStudio and official Speeduino firmware. Verify outputs, sensors and firmware for the actual build and obtain the model-specific pinout before wiring.
The manufacturer provides the revision 2 Universal8 two-connector drawing; verify the hardware revision and actual build before using its assignments. Open the PnPduino pinout document. The separate connector-identification table above is a summary; the full manufacturer-labelled schedule follows below.
Transcribed from the PnPduino PnPduino Universal8 pinout revision 2. Follow the connector drawing in the source and verify the actual build and orientation; the source does not explicitly identify its view as ECU-face or wire-side. Arduino pins are software/board assignments, not connector cavity numbers. A blank manufacturer label is recorded as unlabelled rather than assumed unused.
A-plug input — 34 positions
ECU pin
Manufacturer label
Manufacturer description
Arduino pin
A1
INP4
Spare Input 4
A11
A2
INP1
Spare Input 1
A8
A3
CLT
Engine Coolant Temp
A4
A4
O2
Wideband O2 Sensor
A1
A5
CANH
CAN Hi
STM32
A6
VR2+
VR2+ or Hall Sensor 2
D18
A7
VR1+
VR1+ or Hall Sensor 1
D19
A8
5V Out
5V Out to sensors
—
A9
12V In
12V Input from Ignition switch
—
A10
INP3
Spare Input 3
A10
A11
IAT
Intake Air Temperature
A5
A12
TPS
Throttle Position Sensor
A3
A13
CLUTCH
Clutch Switch
37
A14
CANL
CAN Lo
STM32
A15
VR2-
VR2- or Hall Sensor 2 Logic Ground
—
A16
VR1-
VR1- or Hall Sensor 1 Logic Ground
—
A17
INP5
Spare Input 5
A6
A18
INP9
Spare Input 9
A15
A19
INP2
Spare Input 2
A9
A20
12V Out
Fused 12V Supply to sensors only
—
A21
12V Out
Fused 12V Supply to sensors only
—
A22
12V Out
Fused 12V Supply to sensors only
—
A23
12V Out
Fused 12V Supply to sensors only
—
A24
Not labelled in source
Not labelled in source
—
A25
INP7
Spare Input 7
A13
A26
EXTMAP
External MAP sensor
A0
A27
INP8
Spare Input 8
A14
A28
FLEX
Flex Fuel Sensor
2
A29
HALL4
Hall Sensor 4
3
A30
GRND
ECU Logic Ground
—
A31
GRND
Power Ground
—
A32
GRND
Sensor Ground
—
A33
Not labelled in source
Not labelled in source
—
A34
INP6
Spare Input 6
A12
B-plug output — 34 positions
ECU pin
Manufacturer label
Manufacturer description
Arduino pin
B1
VVT
VVT/VVTI or VTEC/VTC terminology
11
B2
IDLE2
Idle 2 or Spare High Current 1
10
B3
IDLE1
Idle 1 for IACV Solenoid
9
B4
INJ4
Injector 4
5
B5
INJ3
Injector 3
6
B6
INJ2
Injector 2
7
B7
INJ1
Injector 1
8
B8
INJ8
Injector 8
49
B9
INJ7
Injector 7
47
B10
BOOST
Boost or Spare Hi Current 2
12
B11
LC4
Low Current Output 4
29
B12
LC3
Low Current Output 3
28
B13
LC1
Low Current Output 1
26
B14
FAN
Radiator Fan 1
24
B15
TACH
Tachometer Output 5V or 12V
22
B16
FUELP
Fuel Pump or Circuit Opening Relay
23
B17
INJ6
Injector 6
45
B18
IGN4
Ignition Output 4
34
B19
IGN3
Ignition Output 3
33
B20
STP-B2
Stepper Idle Air Coil B2
—
B21
STP-A2
Stepper Idle Air Coil A2
—
B22
FAN2
Radiator Fan 2
25
B23
GRND
Power Ground
—
B24
GRND
Power Ground
—
B25
INJ5
Injector 5
42
B26
IGN1
Ignition Output 1
35
B27
IGN2
Ignition Output 2
36
B28
STP-B1
Stepper Idle Air Coil B1
—
B29
STP-A1
Stepper Idle Air Coil A1
—
B30
LC2
Low Current Output 2
27
B31
IGN8
Ignition Output 8
41
B32
IGN7
Ignition Output 7
40
B33
IGN6
Ignition Output 6
39
B34
IGN5
Ignition Output 5
38
The revision-2 source states that IDLE2 and BOOST can be used as high-current outputs and that a PWM radiator fan should use FAN2. It says vehicle speed can be wired to Hall 3, but does not assign Hall 3 a cavity in this table; A24 and A33 are blank and are not assumed to be Hall 3. Follow the manufacturer’s grounding instructions.