Removed text is struck through; added text is highlighted.
PnPduino Honda B/D OBD1 is a PnPduino programmable engine-management ECU. Manufacturer product information.
PnPduino Honda B/D OBD1. PnPduino manufacturer product photograph, reproduced with permission.
Application and identification
Vehicle-specific standalone for listed 1992–2000 Civic, Integra and Del Sol B-, D- and H-series applications, excluding D17. This is an OBD1-connector ECU: the manufacturer lists OBD2A/B to OBD1 adapters for later looms. Match the original ECU and harness before purchase.
System and wiring
A manufacturer-designed variable-reluctance conditioner supports the original distributor without modifying it. High-impedance aftermarket injectors are required; the original MAP sensor can be retained. Air-conditioning and alternator control are described as working. From version 8 the VTEC relay was replaced by a MOSFET; version 10 onwards can be upgraded to STM32.
Software and calibration
The supplier installs custom firmware and says not to update it. Choose the correct base map; a separate wideband controller and final tuning are required.
See the PnPduino manufacturer index.
Manufacturer ECU connector assignments
Transcribed from the PnPduino Honda B/D pinout, pages 1–4, which views the front of the 64-pin male connector. Pins are numbered top to bottom then left to right. The manufacturer notes that the Arduino pin is used for configurable inputs and outputs in TunerStudio; CAN connections require the STM32 processor. The document distinguishes retained OEM, added and unused wiring in its colour diagrams; check the original before wiring.
Manufacturer source discrepancy: the table’s PnPduino injector assignments at A2, A3 and A5 differ from the injector-channel mapping in its page 4 footnote. Both appear in the document, so confirm the actual build and channel mapping with PnPduino rather than choosing one by assumption. The manufacturer also gives a separate coil-on-plug firing-order note on page 4.
Connector A
ECU pinLabelDescriptionManufacturer remarksArduino pinA1INJ1Injector 1Injector 1 from PnPduino*A2INJ4Injector 4Injector 3 from PnPduino*A3INJ2Injector 2Injector 4 from PnPduino*A4VTSVTEC+12V from PnPduino11A5INJ3Injector 3Injector 2 from PnPduinoA6HTHeater ControlTo OEM O2 sensor, not usedA7FPFuel Pumpuse Board DefA8NONENot usedA9IDLE1Idle 1Only use 2 wire IACVA10LC2Low Current 2Spare output27A11EGREGRNot usedA12FANRadiator FanTo be wired to fan relayuse Board DefA13W/LC4Check Engine LTo be set as programmable output29A14FAN2Fan 2Spare output25A15ACCLow Current 1AC Compressor clutch26A16ALTCLow Current 3Alternator Control Hi or Low28A17IG3Ignition 3For Coil on Plug 4**A18IG2Ignition 2For Coil on Plug 3**A19IG4Ignition 4For Coil on Plug 2**A20EVAPEvap PurgeNot usedA21ICMIgnition 1For ICM Distributor or COP IG1A22ICMIgnition 1For ICM Distributor or COP IG1A23PGPower GroundFor Wideband Power GroundA24PGPower GroundPower Ground (located at Head)A25IGP212V from MRLY12V from Main RelayA26GRNDECU GroundDont mix with Chassis Ground
Connector B
ECU pinLabelDescriptionManufacturer remarksArduino pinB1IGP112V from MRLY12V from Main RelayB2GRNDECU GroundDont mix with Chassis GroundB3BOOSTBoost ControlBoost Control Solenoid12B4GRNDECU GroundDont mix with Chassis GroundB5ACSAC SwitchInput 2 for Idle upA9B612VIgnition SwitchNon-Fused 12V Ignition OutB7CLTCHClutch switchFor Launch Control & FFS37B8FLEXFlex Fuel SensorEthanol Fuel Sensor2B9STSStarter SwitchNot usedB10VSSVehicle SpeedVehicle Speed Sensor20B11CYPPVR2+1 tooth per Rev +B12CYPMVR2-1 tooth per Rev -B13TDCPTDCPNot usedB14TDCMTDCMNot usedB15CKPPVR1+24 tooth per Rev +B16CKPMVR1-24 tooth per Rev -
Connector D
ECU pinLabelDescriptionManufacturer remarksArduino pinD1VBUVoltage BackupNot usedD2BKSWIDLE2Spare output10D3KNOCKKnockKnock input for future update21D4INP7Input 7Spare input 7A13D5CANHCAN HiOnly for STM32 ProcessorD6CANLCAN LoOnly for STM32 ProcessorD7TX/RXINP5Spare Input 5A6D8TACHTachometerTach Output when using COPuse Board DefD9ALTFRAlternator FRNot usedD10ELDINP1Spare input 1A8D11TPSTPSThrottle Position SensorD12INP6Input 6Spare input 6A12D13ECTECTEngine Coolant TemperatureD14O2Oxygen SensorWideband O2 SensorD15IATIATInlet Air TemperatureD16INP4Input 4Spare input 4A11D17MAPMAPExternal Map sensorD18INP3Input 3Spare input 3A10D195V5V outputFused 5V out to MAP & TPSD205V5V outputFused 5V out to MAP & TPSD21GRNDECU GroundDont mix with Power GroundD22GRNDECU GroundDont mix with Power Ground
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Vehicle-specific standalone for listed 1992–2000 Civic, Integra and Del Sol B-, D- and H-series applications, excluding D17. This is an OBD1-connector ECU: the manufacturer lists OBD2A/B to OBD1 adapters for later looms. Match the original ECU and harness before purchase.
System and wiring
A manufacturer-designed variable-reluctance conditioner supports the original distributor without modifying it. High-impedance aftermarket injectors are required; the original MAP sensor can be retained. Air-conditioning and alternator control are described as working. From version 8 the VTEC relay was replaced by a MOSFET; version 10 onwards can be upgraded to STM32.
Software and calibration
The supplier installs custom firmware and says not to update it. Choose the correct base map; a separate wideband controller and final tuning are required.
Transcribed from the PnPduino Honda B/D pinout, pages 1–4, which views the front of the 64-pin male connector. Pins are numbered top to bottom then left to right. The manufacturer notes that the Arduino pin is used for configurable inputs and outputs in TunerStudio; CAN connections require the STM32 processor. The document distinguishes retained OEM, added and unused wiring in its colour diagrams; check the original before wiring.
Manufacturer source discrepancy: the table’s PnPduino injector assignments at A2, A3 and A5 differ from the injector-channel mapping in its page 4 footnote. Both appear in the document, so confirm the actual build and channel mapping with PnPduino rather than choosing one by assumption. The manufacturer also gives a separate coil-on-plug firing-order note on page 4.
Vehicle-specific standalone for listed 1992–2000 Civic, Integra and Del Sol B-, D- and H-series applications, excluding D17. This is an OBD1-connector ECU: the manufacturer lists OBD2A/B to OBD1 adapters for later looms. Match the original ECU and harness before purchase.
System and wiring
A manufacturer-designed variable-reluctance conditioner supports the original distributor without modifying it. High-impedance aftermarket injectors are required; the original MAP sensor can be retained. Air-conditioning and alternator control are described as working. From version 8 the VTEC relay was replaced by a MOSFET; version 10 onwards can be upgraded to STM32.
Software and calibration
The supplier installs custom firmware and says not to update it. Choose the correct base map; a separate wideband controller and final tuning are required.
Transcribed from the PnPduino Honda B/D pinout, pages 1–4, which views the front of the 64-pin male connector. Pins are numbered top to bottom then left to right. The manufacturer notes that the Arduino pin is used for configurable inputs and outputs in TunerStudio; CAN connections require the STM32 processor. The document distinguishes retained OEM, added and unused wiring in its colour diagrams; check the original before wiring.
Manufacturer source discrepancy: the table’s PnPduino injector assignments at A2, A3 and A5 differ from the injector-channel mapping in its page 4 footnote. Both appear in the document, so confirm the actual build and channel mapping with PnPduino rather than choosing one by assumption. The manufacturer also gives a separate coil-on-plug firing-order note on page 4.