Tuning Wiki
Applies to

Check the hardware and software limits stated in this article.

PnPduino Honda B/D OBD1 is a PnPduino programmable engine-management ECU. Manufacturer product information.

PnPduino Honda B/D OBD1
PnPduino Honda B/D OBD1. PnPduino manufacturer product photograph, reproduced with permission.

Application and identification

Vehicle-specific standalone for listed 1992–2000 Civic, Integra and Del Sol B-, D- and H-series applications, excluding D17. This is an OBD1-connector ECU: the manufacturer lists OBD2A/B to OBD1 adapters for later looms. Match the original ECU and harness before purchase.

System and wiring

A manufacturer-designed variable-reluctance conditioner supports the original distributor without modifying it. High-impedance aftermarket injectors are required; the original MAP sensor can be retained. Air-conditioning and alternator control are described as working. From version 8 the VTEC relay was replaced by a MOSFET; version 10 onwards can be upgraded to STM32.

Software and calibration

The supplier installs custom firmware and says not to update it. Choose the correct base map; a separate wideband controller and final tuning are required.

See the PnPduino manufacturer index.

Manufacturer ECU connector assignments

Transcribed from the PnPduino Honda B/D pinout, pages 1–4, which views the front of the 64-pin male connector. Pins are numbered top to bottom then left to right. The manufacturer notes that the Arduino pin is used for configurable inputs and outputs in TunerStudio; CAN connections require the STM32 processor. The document distinguishes retained OEM, added and unused wiring in its colour diagrams; check the original before wiring.

Manufacturer source discrepancy: the table’s PnPduino injector assignments at A2, A3 and A5 differ from the injector-channel mapping in its page 4 footnote. Both appear in the document, so confirm the actual build and channel mapping with PnPduino rather than choosing one by assumption. The manufacturer also gives a separate coil-on-plug firing-order note on page 4.

Connector A

ECU pinLabelDescriptionManufacturer remarksArduino pin
A1INJ1Injector 1Injector 1 from PnPduino*
A2INJ4Injector 4Injector 3 from PnPduino*
A3INJ2Injector 2Injector 4 from PnPduino*
A4VTSVTEC+12V from PnPduino11
A5INJ3Injector 3Injector 2 from PnPduino
A6HTHeater ControlTo OEM O2 sensor, not used
A7FPFuel Pumpuse Board Def
A8NONENot used
A9IDLE1Idle 1Only use 2 wire IACV
A10LC2Low Current 2Spare output27
A11EGREGRNot used
A12FANRadiator FanTo be wired to fan relayuse Board Def
A13W/LC4Check Engine LTo be set as programmable output29
A14FAN2Fan 2Spare output25
A15ACCLow Current 1AC Compressor clutch26
A16ALTCLow Current 3Alternator Control Hi or Low28
A17IG3Ignition 3For Coil on Plug 4**
A18IG2Ignition 2For Coil on Plug 3**
A19IG4Ignition 4For Coil on Plug 2**
A20EVAPEvap PurgeNot used
A21ICMIgnition 1For ICM Distributor or COP IG1
A22ICMIgnition 1For ICM Distributor or COP IG1
A23PGPower GroundFor Wideband Power Ground
A24PGPower GroundPower Ground (located at Head)
A25IGP212V from MRLY12V from Main Relay
A26GRNDECU GroundDont mix with Chassis Ground

Connector B

ECU pinLabelDescriptionManufacturer remarksArduino pin
B1IGP112V from MRLY12V from Main Relay
B2GRNDECU GroundDont mix with Chassis Ground
B3BOOSTBoost ControlBoost Control Solenoid12
B4GRNDECU GroundDont mix with Chassis Ground
B5ACSAC SwitchInput 2 for Idle upA9
B612VIgnition SwitchNon-Fused 12V Ignition Out
B7CLTCHClutch switchFor Launch Control & FFS37
B8FLEXFlex Fuel SensorEthanol Fuel Sensor2
B9STSStarter SwitchNot used
B10VSSVehicle SpeedVehicle Speed Sensor20
B11CYPPVR2+1 tooth per Rev +
B12CYPMVR2-1 tooth per Rev -
B13TDCPTDCPNot used
B14TDCMTDCMNot used
B15CKPPVR1+24 tooth per Rev +
B16CKPMVR1-24 tooth per Rev -

Connector D

ECU pinLabelDescriptionManufacturer remarksArduino pin
D1VBUVoltage BackupNot used
D2BKSWIDLE2Spare output10
D3KNOCKKnockKnock input for future update21
D4INP7Input 7Spare input 7A13
D5CANHCAN HiOnly for STM32 Processor
D6CANLCAN LoOnly for STM32 Processor
D7TX/RXINP5Spare Input 5A6
D8TACHTachometerTach Output when using COPuse Board Def
D9ALTFRAlternator FRNot used
D10ELDINP1Spare input 1A8
D11TPSTPSThrottle Position Sensor
D12INP6Input 6Spare input 6A12
D13ECTECTEngine Coolant Temperature
D14O2Oxygen SensorWideband O2 Sensor
D15IATIATInlet Air Temperature
D16INP4Input 4Spare input 4A11
D17MAPMAPExternal Map sensor
D18INP3Input 3Spare input 3A10
D195V5V outputFused 5V out to MAP & TPS
D205V5V outputFused 5V out to MAP & TPS
D21GRNDECU GroundDont mix with Power Ground
D22GRNDECU GroundDont mix with Power Ground