PnPduino Honda B/D OBD1 is a PnPduino programmable engine-management ECU. Manufacturer product information.

Application and identification
Vehicle-specific standalone for listed 1992–2000 Civic, Integra and Del Sol B-, D- and H-series applications, excluding D17. This is an OBD1-connector ECU: the manufacturer lists OBD2A/B to OBD1 adapters for later looms. Match the original ECU and harness before purchase.
System and wiring
A manufacturer-designed variable-reluctance conditioner supports the original distributor without modifying it. High-impedance aftermarket injectors are required; the original MAP sensor can be retained. Air-conditioning and alternator control are described as working. From version 8 the VTEC relay was replaced by a MOSFET; version 10 onwards can be upgraded to STM32.
Software and calibration
The supplier installs custom firmware and says not to update it. Choose the correct base map; a separate wideband controller and final tuning are required.
See the PnPduino manufacturer index.
Manufacturer ECU connector assignments
Transcribed from the PnPduino Honda B/D pinout, pages 1–4, which views the front of the 64-pin male connector. Pins are numbered top to bottom then left to right. The manufacturer notes that the Arduino pin is used for configurable inputs and outputs in TunerStudio; CAN connections require the STM32 processor. The document distinguishes retained OEM, added and unused wiring in its colour diagrams; check the original before wiring.
Manufacturer source discrepancy: the table’s PnPduino injector assignments at A2, A3 and A5 differ from the injector-channel mapping in its page 4 footnote. Both appear in the document, so confirm the actual build and channel mapping with PnPduino rather than choosing one by assumption. The manufacturer also gives a separate coil-on-plug firing-order note on page 4.
Connector A
| ECU pin | Label | Description | Manufacturer remarks | Arduino pin |
|---|---|---|---|---|
| A1 | INJ1 | Injector 1 | Injector 1 from PnPduino* | |
| A2 | INJ4 | Injector 4 | Injector 3 from PnPduino* | |
| A3 | INJ2 | Injector 2 | Injector 4 from PnPduino* | |
| A4 | VTS | VTEC | +12V from PnPduino | 11 |
| A5 | INJ3 | Injector 3 | Injector 2 from PnPduino | |
| A6 | HT | Heater Control | To OEM O2 sensor, not used | |
| A7 | FP | Fuel Pump | use Board Def | |
| A8 | NONE | Not used | ||
| A9 | IDLE1 | Idle 1 | Only use 2 wire IACV | |
| A10 | LC2 | Low Current 2 | Spare output | 27 |
| A11 | EGR | EGR | Not used | |
| A12 | FAN | Radiator Fan | To be wired to fan relay | use Board Def |
| A13 | W/LC4 | Check Engine L | To be set as programmable output | 29 |
| A14 | FAN2 | Fan 2 | Spare output | 25 |
| A15 | ACC | Low Current 1 | AC Compressor clutch | 26 |
| A16 | ALTC | Low Current 3 | Alternator Control Hi or Low | 28 |
| A17 | IG3 | Ignition 3 | For Coil on Plug 4** | |
| A18 | IG2 | Ignition 2 | For Coil on Plug 3** | |
| A19 | IG4 | Ignition 4 | For Coil on Plug 2** | |
| A20 | EVAP | Evap Purge | Not used | |
| A21 | ICM | Ignition 1 | For ICM Distributor or COP IG1 | |
| A22 | ICM | Ignition 1 | For ICM Distributor or COP IG1 | |
| A23 | PG | Power Ground | For Wideband Power Ground | |
| A24 | PG | Power Ground | Power Ground (located at Head) | |
| A25 | IGP2 | 12V from MRLY | 12V from Main Relay | |
| A26 | GRND | ECU Ground | Dont mix with Chassis Ground |
Connector B
| ECU pin | Label | Description | Manufacturer remarks | Arduino pin |
|---|---|---|---|---|
| B1 | IGP1 | 12V from MRLY | 12V from Main Relay | |
| B2 | GRND | ECU Ground | Dont mix with Chassis Ground | |
| B3 | BOOST | Boost Control | Boost Control Solenoid | 12 |
| B4 | GRND | ECU Ground | Dont mix with Chassis Ground | |
| B5 | ACS | AC Switch | Input 2 for Idle up | A9 |
| B6 | 12V | Ignition Switch | Non-Fused 12V Ignition Out | |
| B7 | CLTCH | Clutch switch | For Launch Control & FFS | 37 |
| B8 | FLEX | Flex Fuel Sensor | Ethanol Fuel Sensor | 2 |
| B9 | STS | Starter Switch | Not used | |
| B10 | VSS | Vehicle Speed | Vehicle Speed Sensor | 20 |
| B11 | CYPP | VR2+ | 1 tooth per Rev + | |
| B12 | CYPM | VR2- | 1 tooth per Rev - | |
| B13 | TDCP | TDCP | Not used | |
| B14 | TDCM | TDCM | Not used | |
| B15 | CKPP | VR1+ | 24 tooth per Rev + | |
| B16 | CKPM | VR1- | 24 tooth per Rev - |
Connector D
| ECU pin | Label | Description | Manufacturer remarks | Arduino pin |
|---|---|---|---|---|
| D1 | VBU | Voltage Backup | Not used | |
| D2 | BKSW | IDLE2 | Spare output | 10 |
| D3 | KNOCK | Knock | Knock input for future update | 21 |
| D4 | INP7 | Input 7 | Spare input 7 | A13 |
| D5 | CANH | CAN Hi | Only for STM32 Processor | |
| D6 | CANL | CAN Lo | Only for STM32 Processor | |
| D7 | TX/RX | INP5 | Spare Input 5 | A6 |
| D8 | TACH | Tachometer | Tach Output when using COP | use Board Def |
| D9 | ALTFR | Alternator FR | Not used | |
| D10 | ELD | INP1 | Spare input 1 | A8 |
| D11 | TPS | TPS | Throttle Position Sensor | |
| D12 | INP6 | Input 6 | Spare input 6 | A12 |
| D13 | ECT | ECT | Engine Coolant Temperature | |
| D14 | O2 | Oxygen Sensor | Wideband O2 Sensor | |
| D15 | IAT | IAT | Inlet Air Temperature | |
| D16 | INP4 | Input 4 | Spare input 4 | A11 |
| D17 | MAP | MAP | External Map sensor | |
| D18 | INP3 | Input 3 | Spare input 3 | A10 |
| D19 | 5V | 5V output | Fused 5V out to MAP & TPS | |
| D20 | 5V | 5V output | Fused 5V out to MAP & TPS | |
| D21 | GRND | ECU Ground | Dont mix with Power Ground | |
| D22 | GRND | ECU Ground | Dont mix with Power Ground |