Removed text is struck through; added text is highlighted.
EVO6L is a standalone sensor and ECU logger with individual Binder sockets. It has a different connector layout from EVO6. For the range overview see AiM in-car dataloggers.
AiM EVO6 and EVO6L loggers. Image: AiM, reproduced with permission; AiM product picture library.
Specifications
ItemSpecificationECUCAN, RS232 or K-LineInputsFive configurable analogue inputs; two speed inputs and coil RPMInertial / GPSThree-axis accelerometer and gyro; GPS09c moduleStorage4 GB internalOutputs / connectorsOne digital output, up to 1 A; thirteen Binder 712 connectors; IP65
Specifications and kit contents: AiM AiM EVO6L technical documentation. Check hardware generation and exact kit.
Pinout
The AiM technical sheet labels each female Binder 712 connector from the external device view. The 7-pin ECU socket is CAN1+ / CAN1− / 9–15 V input / RS232 TX / RS232 RX / K-Line / battery ground in pins 1–7. EXP and GPS are five-pin: CAN+ / ground / +Vbout CAN / CAN− / +Vbext CAN.
EVO6L connectorPin assignmentsPOWER, 2-pin1: 9–15 V power in; 2: battery groundCH1–CH5, each 4-pin1: corresponding analogue input; 2: analogue ground; 3: +Vbout; 4: VrefSpeed, 4-pin1: speed 1; 2: ground; 3: +Vbout; 4: speed 2Beacon, 4-pin1: magnetic lap; 2: ground; 3: +Vbout; 4: optical lapRPM/Dout, 5-pin1: RPM; 2: PGND; 3 and 4: not connected; 5: digital outputUSB, 3-pin1: USB D+; 2: USB D−; 3: ground
Wiring and installation
EVO6L power, ECU and expansion connections; original Tuning Wiki illustration based on AiM documentation. Schematic diagrams do not show physical connector positions unless explicitly labelled.
AiM's kit list identifies CAN or OBD-II leads, GPS09c, power and USB cables. Sensors on CH1–CH5 require correctly rated and configured inputs; the RPM/output lead is separate. Check the kit and power arrangement before combining cables.
Choose the correct model-specific lead and configure the ECU protocol in Race Studio 3. A connector shape alone does not establish vehicle compatibility. Confirm every cavity number, signal level, ground, power source and electrical limit in the linked AiM documentation before wiring; diagrams are from the device view or a conceptual schematic as stated. Secure the loom and make connections with power disconnected.
Software and further reading
Race Studio 3 Analysis example showing suspension traces; actual channels depend on the device and connected sensors. Image: AiM, reproduced with permission; manufacturer source.
Analysis and download: AiM supports PC analysis of EVO6L recordings in Race Studio Analysis. EVO6L and EVO6 differ in their connections; consult the model guide for the download method. AiM model guidance. Download the Windows software from AiM Race Studio 3 software downloads. For capabilities and compatibility see AiM data-log analysis software.
Use AiM Race Studio 3 to configure supported devices and analyse recorded sessions. Check the specific ECU protocol and cable before connection; not every source exposes every channel. Manufacturer references: model documentation; product and installation guidance.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: AiM EVO6L
EVO6L is a standalone sensor and ECU logger with individual Binder sockets. It has a different connector layout from EVO6. For the range overview see AiM in-car dataloggers.
1: magnetic lap; 2: ground; 3: +Vbout; 4: optical lap
RPM/Dout, 5-pin
1: RPM; 2: PGND; 3 and 4: not connected; 5: digital output
USB, 3-pin
1: USB D+; 2: USB D−; 3: ground
Wiring and installation
EVO6L power, ECU and expansion connections; original Tuning Wiki illustration based on AiM documentation. Schematic diagrams do not show physical connector positions unless explicitly labelled.
AiM's kit list identifies CAN or OBD-II leads, GPS09c, power and USB cables. Sensors on CH1–CH5 require correctly rated and configured inputs; the RPM/output lead is separate. Check the kit and power arrangement before combining cables.
Choose the correct model-specific lead and configure the ECU protocol in Race Studio 3. A connector shape alone does not establish vehicle compatibility. Confirm every cavity number, signal level, ground, power source and electrical limit in the linked AiM documentation before wiring; diagrams are from the device view or a conceptual schematic as stated. Secure the loom and make connections with power disconnected.
Software and further reading
Race Studio 3 Analysis example showing suspension traces; actual channels depend on the device and connected sensors. Image: AiM, reproduced with permission; manufacturer source.
Analysis and download: AiM supports PC analysis of EVO6L recordings in Race Studio Analysis. EVO6L and EVO6 differ in their connections; consult the model guide for the download method. AiM model guidance. Download the Windows software from AiM Race Studio 3 software downloads. For capabilities and compatibility see AiM data-log analysis software.
Use AiM Race Studio 3 to configure supported devices and analyse recorded sessions. Check the specific ECU protocol and cable before connection; not every source exposes every channel. Manufacturer references: model documentation; product and installation guidance.
Revision 2: AiM EVO6L
EVO6L is a standalone sensor and ECU logger with individual Binder sockets. It has a different connector layout from EVO6. For the range overview see AiM in-car dataloggers.
1: magnetic lap; 2: ground; 3: +Vbout; 4: optical lap
RPM/Dout, 5-pin
1: RPM; 2: PGND; 3 and 4: not connected; 5: digital output
USB, 3-pin
1: USB D+; 2: USB D−; 3: ground
Wiring and installation
EVO6L power, ECU and expansion connections; original Tuning Wiki illustration based on AiM documentation. Schematic diagrams do not show physical connector positions unless explicitly labelled.
AiM's kit list identifies CAN or OBD-II leads, GPS09c, power and USB cables. Sensors on CH1–CH5 require correctly rated and configured inputs; the RPM/output lead is separate. Check the kit and power arrangement before combining cables.
Choose the correct model-specific lead and configure the ECU protocol in Race Studio 3. A connector shape alone does not establish vehicle compatibility. Confirm every cavity number, signal level, ground, power source and electrical limit in the linked AiM documentation before wiring; diagrams are from the device view or a conceptual schematic as stated. Secure the loom and make connections with power disconnected.
Software and further reading
Race Studio 3 Analysis example showing suspension traces; actual channels depend on the device and connected sensors. Image: AiM, reproduced with permission; manufacturer source.
Analysis and download: AiM supports PC analysis of EVO6L recordings in Race Studio Analysis. EVO6L and EVO6 differ in their connections; consult the model guide for the download method. AiM model guidance. Download the Windows software from AiM Race Studio 3 software downloads. For capabilities and compatibility see AiM data-log analysis software.
Use AiM Race Studio 3 to configure supported devices and analyse recorded sessions. Check the specific ECU protocol and cable before connection; not every source exposes every channel. Manufacturer references: model documentation; product and installation guidance.