Scope: MoTeC SDC2, part 14010, using the two 24-position connectors labelled A (grey) and B (white) in MoTeC’s SDC2 manual dated 22 February 2008, Appendix B, printed pages 14–15. This reference is not the 40-pin SDC or the 32-position SDC3. Verify the actual module, connector face, region, model year and wiring with MoTeC.
Connector A, grey
| Position | Function and source notes |
|---|---|
| A1 | Lateral G input |
| A2 | Throttle position sensor input |
| A3 | Thumbwheel input, 0 V open to 5 V locked |
| A4 | Brake pedal input, 12 V when applied |
| A5 | Handbrake input, 0 V when on |
| A6 | Tacho input, 2 pulses per rpm |
| A7 | AV1, reserved for future use |
| A8 | AV2, reserved for future use |
| A9 | ECU communications, RS232 to MoTeC M800 OEM WRX78 |
| A10 | Yaw sensor input |
| A11 | 0 V to yaw and G sensor |
| A12 | Not connected |
| A13 | Auto/manual switch input, for future use |
| A14 | Rear diff temperature input, 0 V when hot |
| A19 | Yaw/G sensor reference input, 2.5 V |
| A20 | Battery negative input, electronics ground |
| A21 | Yaw test output |
| A22 | Yaw/G sensor supply, 12 V |
| A23 | Thumbwheel supply, 5 V |
A15–A17 are not listed in the cited printed manual. MoTeC’s online support table lists them as not connected; they are omitted here rather than treated as verified on all revisions.
Disputed CAN positions
Do not use this page to assign CAN polarity on A18 and A24. The printed MoTeC manual calls A18 ABS/steering CAN high and A24 CAN low; MoTeC’s online support table gives A18 CAN low and A24 CAN high. Confirm the actual unit and loom with MoTeC before connecting these positions.
Connector B, white
| Position | Function and source notes |
|---|---|
| B1 | Diff mode 3 dash lamp output, active low |
| B2 | Diff mode 2 dash lamp output, active low |
| B3 | Diff mode 1 dash lamp output, active low |
| B4 | Diff open dash lamp output, active low |
| B5 | Battery positive input, electronics power |
| B6 | Battery positive input, electronics power |
| B7 | Diff power input, solenoid power from relay |
| B8 | Diff power input, solenoid power from relay |
| B9 | Diff drive positive output, solenoid positive |
| B10 | Diff relay control output |
| B11 | Auto/manual dash lamp output, active low |
| B12 | Diff locked dash lamp output, active low |
| B13 | Diff mode 4 dash lamp output, active low |
| B14 | 0 V to thumbwheel |
| B15 | Not connected |
| B16 | Battery negative input, electronics ground |
| B17 | Not connected |
| B18 | Rear left speed sensor input, optional magnetic or Hall |
| B19 | Rear right speed sensor input, optional magnetic or Hall |
| B20 | Front left speed sensor input, optional magnetic or Hall |
| B21 | Front right speed sensor input, optional magnetic or Hall |
| B22 | Diff ground input, solenoid ground |
| B23 | Diff ground input, solenoid ground |
| B24 | Diff drive negative output, switched solenoid negative |
Wheel-speed inputs B18–B21 are optional; in the documented standard installation the controller receives speeds and ABS status over the ABS CAN bus. Confirm sensor configuration and the model-specific harness. Source: MoTeC SDC2 manual, Appendix B.