Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- MoTeC SDC Subaru differential slip controller
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- MoTeC, Subaru
Changes from revision 1 to revision 2
Removed text is struck through; added text is highlighted.
MoTeC SDC part 14009, 40-pin connector. This partial table is based on the manufacturer’s SDC manual dated 22 February 2008, Appendix B, and its SDC support article. It is not an SDC2 or SDC3 pinout. Check the connector orientation and exact unit with MoTeC.
PinFunction1Diff mode 3 dash light output, active low2Diff mode 2 dash light output, active low3Diff mode 1 dash light output, active low4Diff open dash light output, active low7Rear diff temperature input, low when hot8Auto/manual switch input, future use9Brake pedal input, battery voltage (12 V) when applied11Handbrake input, low when on12Thumbwheel input135 V output for thumbwheel and G sensor14No connection15Battery positive, electronics16Battery positive, electronics17No connection18Differential solenoid power input19Differential solenoid power input20Differential drive positive output21Differential relay control output22No connection23Differential locked dash light output, active low24Diff mode 4 dash light output, active low25No connection26Rear left wheel speed input27Rear right wheel speed input28Front left wheel speed input29Front right wheel speed input30No connection31Tacho input from ECU, 2 pulses per engine revolution32Throttle position sensor input33Lateral G input340 V to thumbwheel and G sensor35No connection36Battery negative, electronics ground37Battery negative, electronics ground38Differential solenoid ground input39Differential solenoid ground input40Differential solenoid negative output, switchedPinFunction1Diff mode 3 dash light output, active low2Diff mode 2 dash light output, active low3Diff mode 1 dash light output, active low4Diff open dash light output, active low7Rear diff temperature input, low when hot8Auto/manual switch input, future use9Brake pedal input, battery voltage when applied11Handbrake input, low when on12Thumbwheel input135 V output for thumbwheel and G sensor14No connection15Battery positive, electronics16Battery positive, electronics17No connection18Differential solenoid power input19Differential solenoid power input20Differential drive positive output21Differential relay control output22No connection23Differential locked dash light output, active low24Diff mode 4 dash light output, active low25No connection26Rear left wheel speed input27Rear right wheel speed input28Front left wheel speed input29Front right wheel speed input30No connection31Tacho input, 2 pulses per engine revolution32Throttle position sensor input33Lateral G input340 V to thumbwheel and G sensor35No connection36Battery negative, electronics ground37Battery negative, electronics ground38Differential solenoid ground input39Differential solenoid ground input40Differential solenoid negative output, switchedConflicting or configuration-dependent positions
Pins 5 and 6 are deliberately not assigned here: the MoTeC SDC manual lists pin 5 as CAN low and pin 6 as CAN high in its connector and communications tables, but its link table reverses those labels. The online support article also has inconsistent link labels. Confirm the actual controller and board links with MoTeC before connecting CAN.
Pin 10 is omitted because it is configuration-dependent and the manufacturer documents use inconsistent internal-link identifiers for its ABS-input or sensor-ground selection. Consult MoTeC for the exact board revision. Do not infer an assignment from a different SDC model.
Sources: MoTeC SDC manual, Appendix B and Appendix E; MoTeC SDC support article.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: MoTeC SDC 14009 40 pin connector pinout
MoTeC SDC part 14009, 40-pin connector. This partial table is based on the manufacturer’s SDC manual dated 22 February 2008, Appendix B, and its SDC support article. It is not an SDC2 or SDC3 pinout. Check the connector orientation and exact unit with MoTeC.
| Pin | Function |
|---|
| 1 | Diff mode 3 dash light output, active low |
| 2 | Diff mode 2 dash light output, active low |
| 3 | Diff mode 1 dash light output, active low |
| 4 | Diff open dash light output, active low |
| 7 | Rear diff temperature input, low when hot |
| 8 | Auto/manual switch input, future use |
| 9 | Brake pedal input, battery voltage when applied |
| 11 | Handbrake input, low when on |
| 12 | Thumbwheel input |
| 13 | 5 V output for thumbwheel and G sensor |
| 14 | No connection |
| 15 | Battery positive, electronics |
| 16 | Battery positive, electronics |
| 17 | No connection |
| 18 | Differential solenoid power input |
| 19 | Differential solenoid power input |
| 20 | Differential drive positive output |
| 21 | Differential relay control output |
| 22 | No connection |
| 23 | Differential locked dash light output, active low |
| 24 | Diff mode 4 dash light output, active low |
| 25 | No connection |
| 26 | Rear left wheel speed input |
| 27 | Rear right wheel speed input |
| 28 | Front left wheel speed input |
| 29 | Front right wheel speed input |
| 30 | No connection |
| 31 | Tacho input, 2 pulses per engine revolution |
| 32 | Throttle position sensor input |
| 33 | Lateral G input |
| 34 | 0 V to thumbwheel and G sensor |
| 35 | No connection |
| 36 | Battery negative, electronics ground |
| 37 | Battery negative, electronics ground |
| 38 | Differential solenoid ground input |
| 39 | Differential solenoid ground input |
| 40 | Differential solenoid negative output, switched |
Conflicting or configuration-dependent positions
Pins 5 and 6 are deliberately not assigned here: the MoTeC SDC manual lists pin 5 as CAN low and pin 6 as CAN high in its connector and communications tables, but its link table reverses those labels. The online support article also has inconsistent link labels. Confirm the actual controller and board links with MoTeC before connecting CAN.
Pin 10 is omitted because it is configuration-dependent and the manufacturer documents use inconsistent internal-link identifiers for its ABS-input or sensor-ground selection. Consult MoTeC for the exact board revision. Do not infer an assignment from a different SDC model.
Sources: MoTeC SDC manual, Appendix B and Appendix E; MoTeC SDC support article.
Revision 2: MoTeC SDC 14009 40 pin connector pinout
MoTeC SDC part 14009, 40-pin connector. This partial table is based on the manufacturer’s SDC manual dated 22 February 2008, Appendix B, and its SDC support article. It is not an SDC2 or SDC3 pinout. Check the connector orientation and exact unit with MoTeC.
| Pin | Function |
|---|
| 1 | Diff mode 3 dash light output, active low |
| 2 | Diff mode 2 dash light output, active low |
| 3 | Diff mode 1 dash light output, active low |
| 4 | Diff open dash light output, active low |
| 7 | Rear diff temperature input, low when hot |
| 8 | Auto/manual switch input, future use |
| 9 | Brake pedal input, battery voltage (12 V) when applied |
| 11 | Handbrake input, low when on |
| 12 | Thumbwheel input |
| 13 | 5 V output for thumbwheel and G sensor |
| 14 | No connection |
| 15 | Battery positive, electronics |
| 16 | Battery positive, electronics |
| 17 | No connection |
| 18 | Differential solenoid power input |
| 19 | Differential solenoid power input |
| 20 | Differential drive positive output |
| 21 | Differential relay control output |
| 22 | No connection |
| 23 | Differential locked dash light output, active low |
| 24 | Diff mode 4 dash light output, active low |
| 25 | No connection |
| 26 | Rear left wheel speed input |
| 27 | Rear right wheel speed input |
| 28 | Front left wheel speed input |
| 29 | Front right wheel speed input |
| 30 | No connection |
| 31 | Tacho input from ECU, 2 pulses per engine revolution |
| 32 | Throttle position sensor input |
| 33 | Lateral G input |
| 34 | 0 V to thumbwheel and G sensor |
| 35 | No connection |
| 36 | Battery negative, electronics ground |
| 37 | Battery negative, electronics ground |
| 38 | Differential solenoid ground input |
| 39 | Differential solenoid ground input |
| 40 | Differential solenoid negative output, switched |
Conflicting or configuration-dependent positions
Pins 5 and 6 are deliberately not assigned here: the MoTeC SDC manual lists pin 5 as CAN low and pin 6 as CAN high in its connector and communications tables, but its link table reverses those labels. The online support article also has inconsistent link labels. Confirm the actual controller and board links with MoTeC before connecting CAN.
Pin 10 is omitted because it is configuration-dependent and the manufacturer documents use inconsistent internal-link identifiers for its ABS-input or sensor-ground selection. Consult MoTeC for the exact board revision. Do not infer an assignment from a different SDC model.
Sources: MoTeC SDC manual, Appendix B and Appendix E; MoTeC SDC support article.