Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- Bosch Motorsport ABS M5
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Bosch
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Selected 38-position ABS M5 ECU assignments from Bosch Motorsport’s basic ABS M5 diagram F02U.S02.XXX-01 in its M5 kit manual, printed page 52. The drawing contrasts option 1 (direct sensors with ECU TTL wheel-speed outputs) and option 2 (wheel-speed interface). The TTL outputs below are shown for option 1 only. This is not a generic M4 or road ABS pinout; other positions are not specified here. WS and WP and black/white descriptions follow the diagram, without assuming sensor polarity. Identify actual connector orientation and kit configuration from Bosch documentation.
ECU pinFunction in the cited diagram1VBat motor relay; S1 fuse 40 A2Front right wheel-speed TTL output, option 14WS front right, black5V_Stab +5 V7Analog 28WS front left, black10ABS warning lamp12Rear right wheel-speed TTL output, option 113Motor ground14CAN low16WP front right, white17WP rear right, white18WS rear left, black19WP front left, white20CAN2 low21Digital 122Analog 123Front left wheel-speed TTL output, option 125VBat valve relay; S2 fuse 25 A26CAN high28KL15 switched supply; S3 fuse 10 A29WS rear right, black31WP rear left, white32A_GND for pressure sensors33CAN2 high34Rear left wheel-speed TTL output, option 136Front brake-pressure sensor signal37Rear brake-pressure sensor signal38Valve ground
Source: Bosch Motorsport ABS M5 kit manual, section 14.7, page 52, and harness options. The manual includes a separate Clubsport wiring diagram; verify that and the exact supplied harness rather than assuming all variants are the same. Bosch warns M4 and M5 looms are not interchangeable.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Bosch Motorsport ABS M5 ECU connector pinout
Selected 38-position ABS M5 ECU assignments from Bosch Motorsport’s basic ABS M5 diagram F02U.S02.XXX-01 in its M5 kit manual, printed page 52. The drawing contrasts option 1 (direct sensors with ECU TTL wheel-speed outputs) and option 2 (wheel-speed interface). The TTL outputs below are shown for option 1 only. This is not a generic M4 or road ABS pinout; other positions are not specified here. WS and WP and black/white descriptions follow the diagram, without assuming sensor polarity. Identify actual connector orientation and kit configuration from Bosch documentation.
| ECU pin | Function in the cited diagram |
|---|
| 1 | VBat motor relay; S1 fuse 40 A |
| 2 | Front right wheel-speed TTL output, option 1 |
| 4 | WS front right, black |
| 5 | V_Stab +5 V |
| 7 | Analog 2 |
| 8 | WS front left, black |
| 10 | ABS warning lamp |
| 12 | Rear right wheel-speed TTL output, option 1 |
| 13 | Motor ground |
| 14 | CAN low |
| 16 | WP front right, white |
| 17 | WP rear right, white |
| 18 | WS rear left, black |
| 19 | WP front left, white |
| 20 | CAN2 low |
| 21 | Digital 1 |
| 22 | Analog 1 |
| 23 | Front left wheel-speed TTL output, option 1 |
| 25 | VBat valve relay; S2 fuse 25 A |
| 26 | CAN high |
| 28 | KL15 switched supply; S3 fuse 10 A |
| 29 | WS rear right, black |
| 31 | WP rear left, white |
| 32 | A_GND for pressure sensors |
| 33 | CAN2 high |
| 34 | Rear left wheel-speed TTL output, option 1 |
| 36 | Front brake-pressure sensor signal |
| 37 | Rear brake-pressure sensor signal |
| 38 | Valve ground |
Source: Bosch Motorsport ABS M5 kit manual, section 14.7, page 52, and harness options. The manual includes a separate Clubsport wiring diagram; verify that and the exact supplied harness rather than assuming all variants are the same. Bosch warns M4 and M5 looms are not interchangeable.
Revision 1: Bosch Motorsport ABS M5 ECU connector pinout
Selected 38-position ABS M5 ECU assignments from Bosch Motorsport’s basic ABS M5 diagram F02U.S02.XXX-01 in its M5 kit manual, printed page 52. The drawing contrasts option 1 (direct sensors with ECU TTL wheel-speed outputs) and option 2 (wheel-speed interface). The TTL outputs below are shown for option 1 only. This is not a generic M4 or road ABS pinout; other positions are not specified here. WS and WP and black/white descriptions follow the diagram, without assuming sensor polarity. Identify actual connector orientation and kit configuration from Bosch documentation.
| ECU pin | Function in the cited diagram |
|---|
| 1 | VBat motor relay; S1 fuse 40 A |
| 2 | Front right wheel-speed TTL output, option 1 |
| 4 | WS front right, black |
| 5 | V_Stab +5 V |
| 7 | Analog 2 |
| 8 | WS front left, black |
| 10 | ABS warning lamp |
| 12 | Rear right wheel-speed TTL output, option 1 |
| 13 | Motor ground |
| 14 | CAN low |
| 16 | WP front right, white |
| 17 | WP rear right, white |
| 18 | WS rear left, black |
| 19 | WP front left, white |
| 20 | CAN2 low |
| 21 | Digital 1 |
| 22 | Analog 1 |
| 23 | Front left wheel-speed TTL output, option 1 |
| 25 | VBat valve relay; S2 fuse 25 A |
| 26 | CAN high |
| 28 | KL15 switched supply; S3 fuse 10 A |
| 29 | WS rear right, black |
| 31 | WP rear left, white |
| 32 | A_GND for pressure sensors |
| 33 | CAN2 high |
| 34 | Rear left wheel-speed TTL output, option 1 |
| 36 | Front brake-pressure sensor signal |
| 37 | Rear brake-pressure sensor signal |
| 38 | Valve ground |
Source: Bosch Motorsport ABS M5 kit manual, section 14.7, page 52, and harness options. The manual includes a separate Clubsport wiring diagram; verify that and the exact supplied harness rather than assuming all variants are the same. Bosch warns M4 and M5 looms are not interchangeable.