Older Peugeot and Citroën diesels include mechanical injection pumps and electronically managed rotary-pump systems. Identify the engine code, exact pump maker and part number, ECU where fitted, vehicle and emissions equipment before choosing service information or considering tuning. These systems do not all use the same controls and cannot be treated as interchangeable with common-rail HDi.
Identify the injection system first
Citroën's XM technical summary lists three distinct examples: the 2.1 Turbo D XUD11 ATE/L with a mechanical pump; XUD11 BTE/L with Lucas Diesel EPIC electronic injection; and 2.5 Turbo D DK5 ATE/L3 with Bosch MSA 11 7.6 and VP36 electronic injection. The document concerns specific multiplexed XM versions and model years; it is not an all-market year cutoff or proof that every XUD pump is mechanical.
Snap-on's 2013 vehicle-communication manual lists both Lucas and Bosch VP20 equipment for the 1.9 turbo diesel DHX in selected Xantia, Evasion, Jumpy, 406, 806 and Expert examples, and lists Lucas or Bosch VP20 for Citroën Saxo 1.5 VJY/VJZ. It is a diagnostic selection guide, not proof of the pump in a particular vehicle. A 1999 Citroën pocket guide reproduction identifies one TUD5 VJZ example with Lucas DPC R8444 B/662C. Read the physical pump identification and match the service procedure.
1.9 XUD turbo diesel: Bosch pump discussion
A Peugeot 405 owner tutorial identifies its example as a 1.9 XUD9/TE with a Bosch pump. It discusses the boost-responsive diaphragm and LDA cone, fuel delivery and turbo pressure; another participant reports a Lucas-equipped 306. These are individual community claims: the adjustments, quoted pressure limits and performance assertions are not independently verified and do not establish safe settings or apply to Lucas pumps.
Before any pump or boost changes, document the original configuration and service condition, including fuel and intake leaks, cooling, actuator operation and actual boost. A pump specialist can verify timing and delivery against the exact pump specification. Record smoke and temperature under comparable load; visible smoke or the author's perceived gain alone does not validate fuelling, exhaust temperature or reliability. Keep applicable emissions equipment operational.
How boost compensation affects fuelling
Bosch's distributor-pump technical instruction, pages 37–39, explains an LDA pressure compensator: charge pressure acts on a spring-loaded diaphragm and tapered control pin, whose follower changes the full-load fuel limit. At lower boost the mechanism restricts full-load delivery; spring preload influences when the diaphragm responds, while the cone and follower govern how movement changes the limit. The LDA affects the pressure-dependent fuel curve, not simply a fixed increase in fuel everywhere.
The 306 Owners Club LDA discussion illustrates these components and owner-proposed modifications. Pin profiles, spring characteristics and pump calibration differ; the thread's alterations and suggested figures have not been validated as general settings. Before considering a change, check the pressure-signal hose, diaphragm and linkage, and confirm actual boost; a damaged signal path can leave fuel restricted despite boost at the engine. Check response at low, intermediate and higher boost with the pump's own test data rather than judging the curve from a single smoke observation.
The 306 Owners Club rolling-road results thread collects owner-reported XUD builds. For example, it lists a T2/9 mm pump build at 124 bhp and 204 lb-ft and another 9 mm/front-mount-intercooler build at 133 bhp and 228.6 lb-ft. Other listings change the turbo, pump internals or supplementary systems, and participants question some dyno and rpm readings. These are reports rather than controlled comparisons or predicted gains; preserve the full build specification and test conditions when comparing them.
In an XUD7TE pump-build thread, the owner identifies a Bosch 0 460 484 038 as an 8 mm pump with coolant-controlled cold-start features, then reports that a proposed 9 mm donor plunger did not fit the original camplate. These are observations about that build, not a validated parts-compatibility table. Head diameter alone does not establish camplate, drive, governor, cold-start or injector compatibility; identify the actual components and have a specialist verify and calibrate the assembled pump.
Static timing is pump-specific
A period XUD service reference lists XUD9 TF/L D8B with Bosch XUD 212 R 513 and a static TDC pump-lift value of 0.66 mm; its XUD9 BTF/L3 DHX Bosch VP20 XUD BP 02 601 example lists 0.57 mm. These are different factory service examples, not performance-tuning targets. Pump piston travel in millimetres is not crankshaft advance in degrees. Use the exact pump, reference position and measuring method from the applicable service documentation, and check timing with the specified equipment.
The same reference identifies the DHX VP20 as semi-electronic, with a load potentiometer, advance solenoid and needle-lift feedback; it separately describes the D8B mechanical pump. Similar Bosch hardware does not imply identical timing control or interchangeable adjustments.
Bosch's VE technical instruction also describes the internal vane supply pump and pressure-control valve establishing speed-dependent housing pressure, which acts on a hydraulic timing piston and changes running advance. The specified overflow restriction or valve supports housing-pressure regulation and returns fuel for cooling and self-venting. Correct static lift alone therefore does not verify running advance: check fuel supply, air ingress and the advance mechanism using the exact-pump procedure. Housing pressure is not high-pressure injector-line pressure; do not obstruct the return as a tuning shortcut.
Lucas mechanical-pump discussion
In a 306 turbo diesel Lucas pump thread, an owner reported little visible smoke during acceleration through the gears but heavy smoke at low speed in a high gear after changes. That observation is anecdotal and does not validate the suggested settings or establish the cause. It illustrates why comparable load and operating conditions matter: no visible smoke in one test is not proof that fuelling is correct across the full operating range.
A diesel fuel-system reference describes a Lucas DPC turbo-compensator design in which boost acts on diaphragms and alters hydraulic pressure acting on an excess-fuel carriage; an inclined profile makes the increase in maximum delivery progressive. This is a general DPC design example, not evidence that every Lucas-equipped PSA has the same actuator or adjustment. It helps explain why Bosch VE LDA instructions cannot simply be copied to a Lucas pump.
A Lucas Roto-Diesel timing worksheet describes dial-indicator measurement of pump-plunger lift against engine position and identifies two alternative procedures depending on engine type. Select the vehicle's exact Lucas pump reference, method and specification; do not assume the Bosch measurement procedure, reference position or numerical lift applies.
A pump specialist's DPC application index lists, for example, 8443B453D against Citroën BX 1.7 TD / Peugeot 405 and XUD7TE, and 8443B744B against Citroën XM 2.1 Turbo D XUD11ATE. It is a supplier catalogue lead, not a complete interchangeability list. Match the full pump plate and exact service data before ordering parts or calibrating.
1.9 DW8B: mechanical pump with electronic timing control
A French vocational diesel examination technical dossier describes a DW8B Lucas DCN2 mechanically driven pump with electronic management. The controller handles functions including injection advance, EGR and pre/post-heating. The load potentiometer is on the pump and the No. 1 injector carries a needle-lift sensor. A separate DW8 service workbook reproduction describes the needle-lift signal as start-of-injection feedback to the diesel control unit. These are distinct from a common-rail pressure control system.
For a timing or running fault, use the relevant vehicle-specific diagnostic and service procedure to assess the load signal, injector feedback, wiring and commanded advance alongside mechanical timing and fuel supply. An ECU in the system does not prove the pump has a conventional common-rail tune or that an HDi definition can be applied.
In a 2006 Berlingo DW8B discussion, an owner compares Lexia timing readings while investigating sluggishness and explicitly lacks a reference value. The readings and explanations in that thread are not confirmed specifications. Record coolant temperature, speed, load and diagnostic state, and use the correct vehicle and pump documentation for any comparison.
Electronically managed XUD and DK5
The XM examples above distinguish Lucas EPIC and Bosch VP36 systems. Record the pump and controller identities, vehicle configuration, fault codes and current service procedures before deciding whether electronic programming, mechanical repair or specialist pump work is relevant. Do not infer map locations, flash access or wiring from a similar-displacement engine.
XUD11BTE Lucas EPIC
Citroën's XUD11BTE EPIC training reproduction describes ECU-controlled pump metering and advance, a cable-operated accelerator position sensor with a plausibility switch, and inlet pressure and air-temperature inputs. In the documented system the No. 4 injector has needle-lift feedback for measured start of injection and dynamic advance correction. The manufacturer describes the sensor/injector assembly as factory adjusted and prohibits resetting that injector; consult the exact current service procedure. This numbering is specific to the documented system and differs from the DW8B example above.
In the same EPIC training, two separate metering solenoids regulate fuel-cavity volume and shift the rotor; rotor-position feedback closes the delivery loop. A separate advance solenoid and cam-position sensor control timing, with needle-lift information providing dynamic correction. The diagnostic parameter called rotor decoding is described in microseconds of sensor current build-up, not directly as injected milligrams per stroke. Compare the actual parameter and units between diagnostic tools before interpreting logs.
A Lucas Peugeot/Citroën EPIC after-sales guide reproduction documents Laser 2000 live-data names for its XUD11BTE/L3 system. DEBIT PEDALE is the driver fuel demand calculated from pedal position and rpm; DEBIT MAXIMUM is the operating-condition/map-derived limit, while DEBIT MAX TRANS is a temporary acceleration limit that may exceed it. DEBIT ACTUEL is the corrected pump request; DEBIT BRUT is a more stable average before those corrections. These are distinct calculated quantities, not independently measured injector delivery.
The guide distinguishes requested and measured rotor and cam position, as well as CONS AVANCE DYN (requested dynamic advance) and POS AVANCE DYN (measured from engine speed and needle-lift signals). It describes rotor decoding in microseconds and manifold pressure as absolute. Its rotor-position scale can change between cranking and running, so interpret a jump across that state transition cautiously. Labels, units and sample behaviour can differ on other tools: confirm them before comparing logs or drawing tuning conclusions.
Citroën describes an individually selected pump calibration resistor that reports internal pump characteristics to the ECU, and a coolant-temperature protection that can limit fuelling. A resistor substitution is not a validated tuning method; investigate hot-load power reduction alongside temperature, sensor readings and fault state. These details apply to the documented XUD11BTE EPIC configuration.
As a specific identification lead, the Citroën XM 1996 documentation reproduction associates the P8C XUD11BTE L/L3 with Lucas EPIC XUDLC01 and controller reference R04010011B. Match the actual ECU, software, emissions specification and transmission; the reference does not establish that other 2.1 files or EPROMs are interchangeable.
A Peugeot 406 2.1 EPIC discussion reports unstable idle after rotor-sensor work; the owner says the pump was not bench-tested, and a contributor discusses the need for calibration. The reported temporary improvement and suggested remedy are unverified. Inspect fault data and arrange pump-specific testing rather than assuming a sensor swap or shim change fixes another pump.
A Xantia 2.1 TD EPROM discussion illustrates electronic calibration work on an owner's Lucas ECU. The poster reports different keypad-code outcomes on two vehicles and is uncertain about another immobiliser configuration. This is not a verified file or interchangeability guide: identify the ECU and memory, preserve a verified original, and understand vehicle-specific coding and recovery before any work.
DK5 2.5 Turbo D Bosch VP36
The Citroën EDC 1.2.8 training reproduction specifically describes the XM DK5 ATE/L3 VP36 pump with MSA11 7.6: the ECU commands metering and advance, receives pump fuel-slide position feedback, and uses engine-speed and needle-lift signals for injection timing. Its illustrated sensor injector is No. 3; the document warns against adjusting that injector because disassembly can damage its sensor. Diagnose the actual control and feedback signals against vehicle-specific service information; mechanical VE LDA instructions do not define this system.
The same document describes limited ELIT after-sales coding of parameters including idle, full-load delivery and starting quantity, intended only when necessary. These service adjustments are not evidence of a general tuning method, a safe power increase, or the ability to read or rewrite the ECU's calibration. Establish the exact tool function, original settings and documented recovery procedure before changing any coding.
For later common-rail vehicles see the PSA HDi and BlueHDi diesel tuning guide and Boxer and Relay diesel guide. The PSA ECU identification overview links related petrol and diesel material.