Page organisation in this revision
- Page type
- Technical article
- Subject
- Gearboxes
- Parent
- Section level
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Alfa Romeo 4C vehicles use a six-speed Alfa Twin Clutch Transmission (TCT) in the documented examples below. FCA's 2015 service bulletin 21-058-15 identifies a dry dual-clutch transmission with sales code DA5 for the covered 1.8-litre 4C. This guide describes that specific application; it is not a complete specification for every Alfa TCT. Identify the VIN, market, engine, transmission, controllers and software before applying a diagnostic procedure. Compare the separate MiTo C633 TCT guide; do not transfer service values or procedures solely because both use the TCT name.
Transmission warning and body-control software
For specified 2015 4C vehicles built on or before 10 February 2015, FCA's TSB 08-021-15 Rev A / RRT 15-028 describes a brief “Transmission Over Temperature” message, possible engine malfunction lamp and a dynamic-control system that may revert to Natural mode. It lists possible body-control and communication faults, including brake-switch plausibility or missing brake-switch messages. Its historical repair updates the body control module, after applicable diagnosis. The message alone does not establish either a faulty gearbox or a false warning: investigate the actual temperature, other codes and operating conditions under the vehicle-specific test plan and follow the current instructions.
Low-speed shifts and transmission software
Separately, FCA TSB 21-058-15 covers specified 2014–15 4C coupe and convertible vehicles in the stated North American and South Korean markets, built on or before 22 September 2015 with the specified 1.8-litre engine and DA5 dry-clutch transmission. It describes possible transmission whine during shifting, a transmission warning or harsh low-speed shifts. Its historical service path checks vehicle systems and updates transmission-control software, with an engine-control software check. Those symptoms have other causes; neither the bulletin nor a matching build date establishes the condition on a particular car. Check the VIN, complete fault report and current FCA service information before programming or ordering parts.
Fault isolation and service
Preserve the complete transmission, engine, body and network fault report and freeze-frame data before clearing anything. Record warning text, selected and actual gear, driving mode, temperature, when the symptom occurs and prior repairs or software changes.
Use the correct diagnostic tool and test plan to compare clutch and gear requests with available position, pressure, speed and temperature data; check supply, brake-switch states and relevant communications where directed. A warning, low-speed judder or a circuit code is not a component verdict.
Investigate mechanical clutch and gearbox condition, electrical faults and actuation where the model-specific tests indicate. An adaptation or software update cannot repair a leak, worn clutch or damaged wiring.
After the confirmed repair, use the exact vehicle's current fluid, programming and calibration procedures and verify the original symptom. Actuators can move during tests; secure the vehicle and follow the prescribed safety conditions.
Consult the exact owner's handbook for its transmission warnings and operation. FCA's 2015 4C handbook documents the six-speed TCT and driver-facing warning information; different model years or markets may differ. Related: automated clutch control and the electronic gearbox index.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Alfa Romeo 4C TCT gearbox faults and diagnosis
Alfa Romeo 4C vehicles use a six-speed Alfa Twin Clutch Transmission (TCT) in the documented examples below. FCA's 2015 service bulletin 21-058-15 identifies a dry dual-clutch transmission with sales code DA5 for the covered 1.8-litre 4C. This guide describes that specific application; it is not a complete specification for every Alfa TCT. Identify the VIN, market, engine, transmission, controllers and software before applying a diagnostic procedure. Compare the separate MiTo C633 TCT guide; do not transfer service values or procedures solely because both use the TCT name.
Transmission warning and body-control software
For specified 2015 4C vehicles built on or before 10 February 2015, FCA's TSB 08-021-15 Rev A / RRT 15-028 describes a brief “Transmission Over Temperature” message, possible engine malfunction lamp and a dynamic-control system that may revert to Natural mode. It lists possible body-control and communication faults, including brake-switch plausibility or missing brake-switch messages. Its historical repair updates the body control module, after applicable diagnosis. The message alone does not establish either a faulty gearbox or a false warning: investigate the actual temperature, other codes and operating conditions under the vehicle-specific test plan and follow the current instructions.
Low-speed shifts and transmission software
Separately, FCA TSB 21-058-15 covers specified 2014–15 4C coupe and convertible vehicles in the stated North American and South Korean markets, built on or before 22 September 2015 with the specified 1.8-litre engine and DA5 dry-clutch transmission. It describes possible transmission whine during shifting, a transmission warning or harsh low-speed shifts. Its historical service path checks vehicle systems and updates transmission-control software, with an engine-control software check. Those symptoms have other causes; neither the bulletin nor a matching build date establishes the condition on a particular car. Check the VIN, complete fault report and current FCA service information before programming or ordering parts.
Fault isolation and service
- Preserve the complete transmission, engine, body and network fault report and freeze-frame data before clearing anything. Record warning text, selected and actual gear, driving mode, temperature, when the symptom occurs and prior repairs or software changes.
- Use the correct diagnostic tool and test plan to compare clutch and gear requests with available position, pressure, speed and temperature data; check supply, brake-switch states and relevant communications where directed. A warning, low-speed judder or a circuit code is not a component verdict.
- Investigate mechanical clutch and gearbox condition, electrical faults and actuation where the model-specific tests indicate. An adaptation or software update cannot repair a leak, worn clutch or damaged wiring.
- After the confirmed repair, use the exact vehicle's current fluid, programming and calibration procedures and verify the original symptom. Actuators can move during tests; secure the vehicle and follow the prescribed safety conditions.
Consult the exact owner's handbook for its transmission warnings and operation. FCA's 2015 4C handbook documents the six-speed TCT and driver-facing warning information; different model years or markets may differ. Related: automated clutch control and the electronic gearbox index.
Revision 1: Alfa Romeo 4C TCT gearbox faults and diagnosis
Alfa Romeo 4C vehicles use a six-speed Alfa Twin Clutch Transmission (TCT) in the documented examples below. FCA's 2015 service bulletin 21-058-15 identifies a dry dual-clutch transmission with sales code DA5 for the covered 1.8-litre 4C. This guide describes that specific application; it is not a complete specification for every Alfa TCT. Identify the VIN, market, engine, transmission, controllers and software before applying a diagnostic procedure. Compare the separate MiTo C633 TCT guide; do not transfer service values or procedures solely because both use the TCT name.
Transmission warning and body-control software
For specified 2015 4C vehicles built on or before 10 February 2015, FCA's TSB 08-021-15 Rev A / RRT 15-028 describes a brief “Transmission Over Temperature” message, possible engine malfunction lamp and a dynamic-control system that may revert to Natural mode. It lists possible body-control and communication faults, including brake-switch plausibility or missing brake-switch messages. Its historical repair updates the body control module, after applicable diagnosis. The message alone does not establish either a faulty gearbox or a false warning: investigate the actual temperature, other codes and operating conditions under the vehicle-specific test plan and follow the current instructions.
Low-speed shifts and transmission software
Separately, FCA TSB 21-058-15 covers specified 2014–15 4C coupe and convertible vehicles in the stated North American and South Korean markets, built on or before 22 September 2015 with the specified 1.8-litre engine and DA5 dry-clutch transmission. It describes possible transmission whine during shifting, a transmission warning or harsh low-speed shifts. Its historical service path checks vehicle systems and updates transmission-control software, with an engine-control software check. Those symptoms have other causes; neither the bulletin nor a matching build date establishes the condition on a particular car. Check the VIN, complete fault report and current FCA service information before programming or ordering parts.
Fault isolation and service
- Preserve the complete transmission, engine, body and network fault report and freeze-frame data before clearing anything. Record warning text, selected and actual gear, driving mode, temperature, when the symptom occurs and prior repairs or software changes.
- Use the correct diagnostic tool and test plan to compare clutch and gear requests with available position, pressure, speed and temperature data; check supply, brake-switch states and relevant communications where directed. A warning, low-speed judder or a circuit code is not a component verdict.
- Investigate mechanical clutch and gearbox condition, electrical faults and actuation where the model-specific tests indicate. An adaptation or software update cannot repair a leak, worn clutch or damaged wiring.
- After the confirmed repair, use the exact vehicle's current fluid, programming and calibration procedures and verify the original symptom. Actuators can move during tests; secure the vehicle and follow the prescribed safety conditions.
Consult the exact owner's handbook for its transmission warnings and operation. FCA's 2015 4C handbook documents the six-speed TCT and driver-facing warning information; different model years or markets may differ. Related: automated clutch control and the electronic gearbox index.