MoTeC C125 (MoTeC part #18065) is a motorsport display and acquisition device. The information here is specific to the cited part; check the label, hardware revision, options and vehicle protocol before connection.

Specifications and options
- 5-inch colour TFT display, 800 × 480 pixels; configurable channels, alarms and display layouts.
- Internal logging is an upgrade: 120 MB and rates up to 500 samples per second; USB logging is a further option. Confirm logging is enabled on the unit or included in the purchased kit.
- Two configurable CAN buses; two RS232 ports. Two digital and three speed inputs are listed. Six analogue voltage inputs, two temperature inputs and four low-side outputs require the I/O upgrade.
- Manufacturer lists 6–32 V DC operation, three-axis accelerometer and optional T2 telemetry; i2 analysis, GPS timing and connected sensors depend on the installation and options.
MoTeC identifies a previous part #18060; dimensions or construction may differ. Use the document for the unit in hand.
Connector and pinout
34-way (mating connector #65044): the table below follows the manufacturer’s pinout for part #18065. Check cavity numbering and the manufacturer's connector view; the functional map is not a physical connector-face drawing. Blank cells retain the source's unspecified function; do not assign them by assumption. Inputs marked as optional need the appropriate enabled upgrade.
| Pin | Name | Function |
|---|---|---|
| 1 | E-TX– | Ethernet Transmit – |
| 2 | E-TX+ | Ethernet Transmit + |
| 3 | AV1 | Analogue Voltage Input 1 (with I/O upgrade) |
| 4 | AV2 | Analogue Voltage Input 2 (with I/O upgrade) |
| 5 | AV3 | Analogue Voltage Input 3 (with I/O upgrade) |
| 6 | AV4 | Analogue Voltage Input 4 (with I/O upgrade) |
| 7 | 8V | Sensor 8 V |
| 8 | 5V | Sensor 5 V |
| 9 | 0V | Sensor 0 V |
| 10 | E-RX– | Ethernet Receive – |
| 11 | E-RX+ | Ethernet Receive + |
| 12 | AV5 | Analogue Voltage Input 5 (with I/O upgrade) |
| 13 | AV6 | Analogue Voltage Input 6 (with I/O upgrade) |
| 14 | DIG1 | Digital Input 1 |
| 15 | DIG2 | Digital Input 2 |
| 16 | AT1 | Analogue Temp Input 1 (with I/O upgrade) |
| 17 | AT2 | Analogue Temp Input 2 (with I/O upgrade) |
| 18 | CAN1L | CAN1 Lo |
| 19 | CAN1H | CAN1 Hi |
| 20 | RS232-1 TX | RS232-1 Transmit |
| 21 | SPD1 | Speed Input 1 |
| 22 | SPD2 | Speed Input 2 |
| 23 | SPD3 | Speed Input 3 |
| 24 | VID1 | Video Input 1 * |
| 25 | RS232-2 RX | RS232-2 Receive |
| 26 | CAN2L | CAN2 Lo/RS232 Ground Input |
| 27 | CAN2H | CAN2 Hi/RS232 Receive |
| 28 | RS232-1 RX | RS232-1 Receive Input |
| 29 | AUX1 | Auxiliary Output 1 (with I/O upgrade) |
| 30 | AUX2 | Auxiliary Output 2 (with I/O upgrade) |
| 31 | AUX3 | Auxiliary Output 3 (with I/O upgrade) |
| 32 | AUX4 | Auxiliary Output 4 (with I/O upgrade) |
| 33 | BAT+ | Battery Positive |
| 34 | BAT– | Battery Negative |
* MoTeC lists live display of the composite video input as requiring the Display Creator upgrade on this C125. Confirm the exact part and revision. MoTeC product specification.
Wiring and configuration
Use the correct connector, power and sensor return for this unit. Match CAN high and low to a compatible, correctly configured network and check existing termination. ECU channels, sensors and lap timing depend on the specific hardware, protocol, configuration and licensed options. Use manufacturer instructions for wire gauge, supply protection and continuity checks; do not connect vehicle battery voltage to a sensor reference output.
MoTeC i2 supports reviewing recorded data; Pro analysis and T2 telemetry require the applicable upgrades. A telemetry licence alone does not provide a radio or cellular connection. See the MoTeC manufacturer guide for family comparisons and references.