Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Datalogging and telematics
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Bosch Motorsport

Changes from revision 1 to revision 2

Removed text is struck through; added text is highlighted.

CG 3.2 combines dual 5G modems with 4G fallback, GNSS, Wi-Fi, Ethernet, CAN-FD, RS232 and 16 GB onboard storage. Bosch describes RaceConnect Cloud live telemetry, but rollout of individual functions, data plans, coverage and regional approval depend on configuration and current service. Bosch CG 3.2 product specification.

Bosch Motorsport CG 3.2 telemetry gateway. Image: Bosch Motorsport, reproduced with permission; manufacturer source.

Data analysis softwareWinDarab V7 example showing lap traces and circuit map. Image: Bosch Motorsport, reproduced with permission; manufacturer product page.Bosch describes the CG 3.2 as a connected telemetry gateway for RaceConnect Cloud. The WinDarab image shows Bosch analysis software for supported loggers; it does not establish direct compatibility with CG 3.2 recordings. Confirm the configured gateway, service and data format with Bosch. CG 3.2 telemetry information.WinDarab V7 download, documentation and edition information. RaceCon is a separate configuration tool for compatible devices. See the Bosch Motorsport software overview.

Connector and pinout

Bosch lists AS612-35SN as mating connector. The following is connector A as numbered by Bosch. Ethernet and serial data are named from the unit's perspective. The diagram is conceptual, not a physical cavity view; use the manufacturer's numbered diagram.

CG 3.2 selected power and communication groups. Original wiki functional schematic, not a connector-face view. Source: Bosch Motorsport documentation; use the manufacturer's drawings and pin numbers.

PinFunctionA-1COMSCR Ethernet cable screenA-2ETHA_TRX−A-3ETH3_TXNA-4ETH3_RXPA-5ETH3_RXNA-6ETH2_TXPA-7ETH2_RXPA-8ETH1_TXPA-9ETH1_TXNA-10ETH1_RXPA-11CAN1_HA-12ReservedA-13GND supplyA-14V_BAT 8–18 VA-15ETHA_TRX+A-16ETH3_TXPA-17ETH2_TXNA-18ETH2_RXNA-19ETH1_RXNA-20CAN1_LA-21RS232_RXA-22RS232_TX

Four gold SMA sockets serve mobile antennas, one gold SMA GNSS and one silver reverse-polarity SMA Wi-Fi. Correct antenna selection, data plan, cable routing and series rules must be checked.

Installation and related information

Confirm the precise model, hardware revision, enabled options and manufacturer's wiring diagram before connecting. Use correct power protection, sensor limits and the chosen ECU protocol; a compatible connector does not guarantee compatible data. Configure in the appropriate Bosch software and verify a short recording or connection. See the Bosch Motorsport manufacturer overview.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 1: Bosch Motorsport CG 3.2

CG 3.2 combines dual 5G modems with 4G fallback, GNSS, Wi-Fi, Ethernet, CAN-FD, RS232 and 16 GB onboard storage. Bosch describes RaceConnect Cloud live telemetry, but rollout of individual functions, data plans, coverage and regional approval depend on configuration and current service. Bosch CG 3.2 product specification.

Bosch Motorsport CG 3.2 telemetry gateway
Bosch Motorsport CG 3.2 telemetry gateway. Image: Bosch Motorsport, reproduced with permission; manufacturer source.

Connector and pinout

Bosch lists AS612-35SN as mating connector. The following is connector A as numbered by Bosch. Ethernet and serial data are named from the unit's perspective. The diagram is conceptual, not a physical cavity view; use the manufacturer's numbered diagram.

CG 3.2 selected power and communication groups
CG 3.2 selected power and communication groups. Original wiki functional schematic, not a connector-face view. Source: Bosch Motorsport documentation; use the manufacturer's drawings and pin numbers.
PinFunction
A-1COMSCR Ethernet cable screen
A-2ETHA_TRX−
A-3ETH3_TXN
A-4ETH3_RXP
A-5ETH3_RXN
A-6ETH2_TXP
A-7ETH2_RXP
A-8ETH1_TXP
A-9ETH1_TXN
A-10ETH1_RXP
A-11CAN1_H
A-12Reserved
A-13GND supply
A-14V_BAT 8–18 V
A-15ETHA_TRX+
A-16ETH3_TXP
A-17ETH2_TXN
A-18ETH2_RXN
A-19ETH1_RXN
A-20CAN1_L
A-21RS232_RX
A-22RS232_TX

Four gold SMA sockets serve mobile antennas, one gold SMA GNSS and one silver reverse-polarity SMA Wi-Fi. Correct antenna selection, data plan, cable routing and series rules must be checked.

Installation and related information

Confirm the precise model, hardware revision, enabled options and manufacturer's wiring diagram before connecting. Use correct power protection, sensor limits and the chosen ECU protocol; a compatible connector does not guarantee compatible data. Configure in the appropriate Bosch software and verify a short recording or connection. See the Bosch Motorsport manufacturer overview.

Revision 2: Bosch Motorsport CG 3.2

CG 3.2 combines dual 5G modems with 4G fallback, GNSS, Wi-Fi, Ethernet, CAN-FD, RS232 and 16 GB onboard storage. Bosch describes RaceConnect Cloud live telemetry, but rollout of individual functions, data plans, coverage and regional approval depend on configuration and current service. Bosch CG 3.2 product specification.

Bosch Motorsport CG 3.2 telemetry gateway
Bosch Motorsport CG 3.2 telemetry gateway. Image: Bosch Motorsport, reproduced with permission; manufacturer source.

Data analysis software

Bosch Motorsport WinDarab V7 analysis showing lap traces and circuit map
WinDarab V7 example showing lap traces and circuit map. Image: Bosch Motorsport, reproduced with permission; manufacturer product page.

Bosch describes the CG 3.2 as a connected telemetry gateway for RaceConnect Cloud. The WinDarab image shows Bosch analysis software for supported loggers; it does not establish direct compatibility with CG 3.2 recordings. Confirm the configured gateway, service and data format with Bosch. CG 3.2 telemetry information.

WinDarab V7 download, documentation and edition information. RaceCon is a separate configuration tool for compatible devices. See the Bosch Motorsport software overview.

Connector and pinout

Bosch lists AS612-35SN as mating connector. The following is connector A as numbered by Bosch. Ethernet and serial data are named from the unit's perspective. The diagram is conceptual, not a physical cavity view; use the manufacturer's numbered diagram.

CG 3.2 selected power and communication groups
CG 3.2 selected power and communication groups. Original wiki functional schematic, not a connector-face view. Source: Bosch Motorsport documentation; use the manufacturer's drawings and pin numbers.
PinFunction
A-1COMSCR Ethernet cable screen
A-2ETHA_TRX−
A-3ETH3_TXN
A-4ETH3_RXP
A-5ETH3_RXN
A-6ETH2_TXP
A-7ETH2_RXP
A-8ETH1_TXP
A-9ETH1_TXN
A-10ETH1_RXP
A-11CAN1_H
A-12Reserved
A-13GND supply
A-14V_BAT 8–18 V
A-15ETHA_TRX+
A-16ETH3_TXP
A-17ETH2_TXN
A-18ETH2_RXN
A-19ETH1_RXN
A-20CAN1_L
A-21RS232_RX
A-22RS232_TX

Four gold SMA sockets serve mobile antennas, one gold SMA GNSS and one silver reverse-polarity SMA Wi-Fi. Correct antenna selection, data plan, cable routing and series rules must be checked.

Installation and related information

Confirm the precise model, hardware revision, enabled options and manufacturer's wiring diagram before connecting. Use correct power protection, sensor limits and the chosen ECU protocol; a compatible connector does not guarantee compatible data. Configure in the appropriate Bosch software and verify a short recording or connection. See the Bosch Motorsport manufacturer overview.