Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- Davis Technologies Profiler EFI
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Davis Technologies
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Davis Technologies Profiler EFI · Davis Technologies traction control systems
Scope and identification
This table transcribes the P1 20-gauge, 14-position connector in the manufacturer’s Profiler EFI instructions, printed page 19. Refer to the source connector illustration to identify pin numbering and orientation on the actual harness. Confirm controller version, ECU integration and optional features before wiring; do not transfer this table to other controllers solely because their plugs look alike.
P1 assignments
PinWire colourFunctionSource flag1RedBattery positive / ignition switch2Yellow with black stripeCAN low* #3GreenDriveshaft RPM VR sensor input +* #4WhiteDriveshaft RPM input5Orange with black stripeTransbrake sync input6TanArming switch7Orange with white stripeAnalog input*8BlackBattery ground9Yellow with red stripeCAN high* #10White with black stripeDriveshaft RPM VR sensor input −* #11OrangeDriveshaft RPM output*12BlueLaunch sync trigger output, 750 mA, Pos-Neg (manufacturer wording)*13Light greenCorrection output14GraySmartDrop output
* = Optional/future-use wire supplied but not installed in the connector, as described in the manual. # = twisted pair. VR means variable reluctance; RPM means revolutions per minute. These markings describe the manual's configuration, not a guarantee that any given used harness is populated as supplied.
Source
Davis Technologies Profiler EFI instructions, printed page 19.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Davis Technologies Profiler EFI P1 connector pinout
Davis Technologies Profiler EFI · Davis Technologies traction control systems
Scope and identification
This table transcribes the P1 20-gauge, 14-position connector in the manufacturer’s Profiler EFI instructions, printed page 19. Refer to the source connector illustration to identify pin numbering and orientation on the actual harness. Confirm controller version, ECU integration and optional features before wiring; do not transfer this table to other controllers solely because their plugs look alike.
P1 assignments
| Pin | Wire colour | Function | Source flag |
|---|
| 1 | Red | Battery positive / ignition switch | |
| 2 | Yellow with black stripe | CAN low | * # |
| 3 | Green | Driveshaft RPM VR sensor input + | * # |
| 4 | White | Driveshaft RPM input | |
| 5 | Orange with black stripe | Transbrake sync input | |
| 6 | Tan | Arming switch | |
| 7 | Orange with white stripe | Analog input | * |
| 8 | Black | Battery ground | |
| 9 | Yellow with red stripe | CAN high | * # |
| 10 | White with black stripe | Driveshaft RPM VR sensor input − | * # |
| 11 | Orange | Driveshaft RPM output | * |
| 12 | Blue | Launch sync trigger output, 750 mA, Pos-Neg (manufacturer wording) | * |
| 13 | Light green | Correction output | |
| 14 | Gray | SmartDrop output | |
* = Optional/future-use wire supplied but not installed in the connector, as described in the manual. # = twisted pair. VR means variable reluctance; RPM means revolutions per minute. These markings describe the manual's configuration, not a guarantee that any given used harness is populated as supplied.
Source
Davis Technologies Profiler EFI instructions, printed page 19.
Revision 1: Davis Technologies Profiler EFI P1 connector pinout
Davis Technologies Profiler EFI · Davis Technologies traction control systems
Scope and identification
This table transcribes the P1 20-gauge, 14-position connector in the manufacturer’s Profiler EFI instructions, printed page 19. Refer to the source connector illustration to identify pin numbering and orientation on the actual harness. Confirm controller version, ECU integration and optional features before wiring; do not transfer this table to other controllers solely because their plugs look alike.
P1 assignments
| Pin | Wire colour | Function | Source flag |
|---|
| 1 | Red | Battery positive / ignition switch | |
| 2 | Yellow with black stripe | CAN low | * # |
| 3 | Green | Driveshaft RPM VR sensor input + | * # |
| 4 | White | Driveshaft RPM input | |
| 5 | Orange with black stripe | Transbrake sync input | |
| 6 | Tan | Arming switch | |
| 7 | Orange with white stripe | Analog input | * |
| 8 | Black | Battery ground | |
| 9 | Yellow with red stripe | CAN high | * # |
| 10 | White with black stripe | Driveshaft RPM VR sensor input − | * # |
| 11 | Orange | Driveshaft RPM output | * |
| 12 | Blue | Launch sync trigger output, 750 mA, Pos-Neg (manufacturer wording) | * |
| 13 | Light green | Correction output | |
| 14 | Gray | SmartDrop output | |
* = Optional/future-use wire supplied but not installed in the connector, as described in the manual. # = twisted pair. VR means variable reluctance; RPM means revolutions per minute. These markings describe the manual's configuration, not a guarantee that any given used harness is populated as supplied.
Source
Davis Technologies Profiler EFI instructions, printed page 19.