Page organisation in this revision
- Page type
- Technical article
- Subject
- ABS / DSC
- Parent
- Davis Technologies TC-3
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- Davis Technologies
Changes from revision 1 to revision 1
Removed text is struck through; added text is highlighted.
Davis Technologies TC-3 · Davis Technologies traction control systems
Scope and identification
This table transcribes the P1 20-gauge, 14-position connector in the manufacturer’s TC-3 instructions, printed page 18. Refer to the source connector illustration to identify pin numbering and orientation on the actual harness. Confirm controller version, ECU integration and optional features before wiring; do not transfer this table to other controllers solely because their plugs look alike.
P1 assignments
PinWire colourFunctionSource flag1RedBattery positive / ignition switch2Yellow with black stripeCAN low* #3GreenDriveshaft RPM VR sensor input +* #4WhiteDriveshaft RPM input5Orange with black stripeTransbrake sync input6TanArming switch7Orange with white stripeAnalog input*8BlackBattery ground9Yellow with red stripeCAN high* #10White with black stripeDriveshaft RPM VR sensor input −* #11OrangeDriveshaft RPM output*12BlueLaunch sync trigger output, 750 mA, Pos-Neg (manufacturer wording)*13Light greenCorrection output14GraySmartDrop output
* = Optional/future-use wire supplied but not installed in the connector, as described in the manual. # = twisted pair. VR means variable reluctance; RPM means revolutions per minute. These markings describe the manual's configuration, not a guarantee that any given used harness is populated as supplied.
Source
Davis Technologies TC-3 instructions, printed page 18.
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 1: Davis Technologies TC-3 P1 connector pinout
Davis Technologies TC-3 · Davis Technologies traction control systems
Scope and identification
This table transcribes the P1 20-gauge, 14-position connector in the manufacturer’s TC-3 instructions, printed page 18. Refer to the source connector illustration to identify pin numbering and orientation on the actual harness. Confirm controller version, ECU integration and optional features before wiring; do not transfer this table to other controllers solely because their plugs look alike.
P1 assignments
| Pin | Wire colour | Function | Source flag |
|---|
| 1 | Red | Battery positive / ignition switch | |
| 2 | Yellow with black stripe | CAN low | * # |
| 3 | Green | Driveshaft RPM VR sensor input + | * # |
| 4 | White | Driveshaft RPM input | |
| 5 | Orange with black stripe | Transbrake sync input | |
| 6 | Tan | Arming switch | |
| 7 | Orange with white stripe | Analog input | * |
| 8 | Black | Battery ground | |
| 9 | Yellow with red stripe | CAN high | * # |
| 10 | White with black stripe | Driveshaft RPM VR sensor input − | * # |
| 11 | Orange | Driveshaft RPM output | * |
| 12 | Blue | Launch sync trigger output, 750 mA, Pos-Neg (manufacturer wording) | * |
| 13 | Light green | Correction output | |
| 14 | Gray | SmartDrop output | |
* = Optional/future-use wire supplied but not installed in the connector, as described in the manual. # = twisted pair. VR means variable reluctance; RPM means revolutions per minute. These markings describe the manual's configuration, not a guarantee that any given used harness is populated as supplied.
Source
Davis Technologies TC-3 instructions, printed page 18.
Revision 1: Davis Technologies TC-3 P1 connector pinout
Davis Technologies TC-3 · Davis Technologies traction control systems
Scope and identification
This table transcribes the P1 20-gauge, 14-position connector in the manufacturer’s TC-3 instructions, printed page 18. Refer to the source connector illustration to identify pin numbering and orientation on the actual harness. Confirm controller version, ECU integration and optional features before wiring; do not transfer this table to other controllers solely because their plugs look alike.
P1 assignments
| Pin | Wire colour | Function | Source flag |
|---|
| 1 | Red | Battery positive / ignition switch | |
| 2 | Yellow with black stripe | CAN low | * # |
| 3 | Green | Driveshaft RPM VR sensor input + | * # |
| 4 | White | Driveshaft RPM input | |
| 5 | Orange with black stripe | Transbrake sync input | |
| 6 | Tan | Arming switch | |
| 7 | Orange with white stripe | Analog input | * |
| 8 | Black | Battery ground | |
| 9 | Yellow with red stripe | CAN high | * # |
| 10 | White with black stripe | Driveshaft RPM VR sensor input − | * # |
| 11 | Orange | Driveshaft RPM output | * |
| 12 | Blue | Launch sync trigger output, 750 mA, Pos-Neg (manufacturer wording) | * |
| 13 | Light green | Correction output | |
| 14 | Gray | SmartDrop output | |
* = Optional/future-use wire supplied but not installed in the connector, as described in the manual. # = twisted pair. VR means variable reluctance; RPM means revolutions per minute. These markings describe the manual's configuration, not a guarantee that any given used harness is populated as supplied.
Source
Davis Technologies TC-3 instructions, printed page 18.